Bebe Care Cloud Cot + Mattress Package Deal Instruction Manual
- June 4, 2024
- Bebe Care
Table of Contents
Bebe Care Cloud Cot + Mattress Package Deal
IMPORTANT: RETAIN FOR FUTURE REFERENCE, READ CAREFULLY.
SAFETY PRECAUTIONS
Read all instructions before assembly and use of the cot. Keep instructions for future use.
WARNING
ADULT ASSEMBLY REQUIRED
- DUE TO THE PRESENCE OF SMALL PARTS DURING ASSEMBLY, KEEP OUT OF REACH OF CHILDREN UNTIL ASSEMBLY IS COMPLETE.
- TO PREVENT FALLS, THE MATTRESS BASE OF THIS COT SHOULD BE ADJUSTED TO THE LOWEST POSITION BEFORE THE CHILD CAN SIT UP.
RECOMMENDED MATTRESS SIZE
- 1300MM LONG X 690 MM WIDE X 100-150 MM THICK.
- FOLLOW THE MANUFACTURER’S ASSEMBLY INSTRUCTIONS TO ENSURE THE SAFETY FEATURES OF THE COT ARE NOT COMPROMISED.
This cot has been manufactured for one child only, with a maximum weight of 18kgs in cot configuration. When the mattress base is assembled in the lower position, ensure the higher cot base holes are covered tightly with the filling bolts supplied. This is to prevent finger entrapment, swallowing and inhalation hazards. ENSURE the cot is placed at a reasonable distance from curtains, blinds, heaters and power points. ENSURE the cot is completely assembled and check that all parts are securely tightened before placing the child into the cot. ENSURE medication, string, elastic, small toys or small items such as money etc are always kept out of the child’s reach when in the cot. DO NOT over-tighten bolts/screws. ENSURE that the child is clear of any moving parts when adjusting the cot. For warranty purposes, keep your sales receipt to provide proof of purchase.
RECOMMENDED MATTRESS SIZE (SOLD SEPARATELY)
- THIS COT HAS BEEN MANUFACTURED FOR USE WITH A MATTRESS THAT MEASURES 1300MM LONG BY 690 MM WIDE AND 100-150 MM IN THICKNESS.
- The width and length are specified because it is important that the gaps between the mattress and the sides and ends of the cot will not exceed 40 mm when the mattress is pushed to one side or end, and 20mm when the mattress is centered in the cot.
- This is to minimize the risk of a child’s limb becoming caught in the gap.
- The thickness of the mattress has been specified to ensure that the depth of the cot is greater than 500 mm with the mattress base in the lower position and is greater than 300mm with the mattress base in the upper position, to minimize the risk of a child climbing or falling out of the cot.
CONGRATULATIONS
Congratulations on your purchase of the Bebecare Cloud Cot.
This product has been designed and developed with safety, comfort, and functionality in mind. Please take the time to read this manual carefully before using this product and keep it in a safe place for future reference.
Due to variations in the style and design of our products, the photographs and illustrations shown in this instruction manual are generic, therefore product fabrics, color, and design may vary from the images shown. CNP Brands reserves the right to alter product specifications without notice as a result of our ongoing policy of product improvement.
ASSEMBLY CONTENTS
Check what you have received
- You have received 1 box. Please check the contents of the box against the list below. If anything is missing, please contact Customer Service.
- In Australia, contact CNP Brands on 1300 667 137, in New Zealand contact Wainhouse Distribution at 0800 567 5000.
Supplied loose in the box
Assembly Kit
ASSEMBLY / OPERATING INSTRUCTIONS
- It is advisable that two people assemble the cot in the room in which it is to be used.
- As small parts are involved in assembly, children should be kept clear of the assembly area.
- Dispose of all packaging material immediately after the cot is assembled.
- Identify all parts and components.
- Clear an area on the floor for assembly and place a sheet on the floor to ensure the cot is not scratched during assembly.
WARNING: DO NOT OVER-TIGHTEN BOLTS. OVER-TIGHTENING BOLTS CAN CAUSE PANELS TO CRACK.
To assemble Cot
- Attach both End Panels to one Side Panel using 4 x 60mm bolts.
- Tighten Until Firm.
- The cot should now resemble the photo opposite.
- Carefully lay the cot down on the Side Panel.
- Slide the Mattress Base between the End Panels.
- WARNING: THE MATTRESS BASE ‘THIS SIDE UP’ LABEL MUST BE FACING UPWARD WHEN MATTRESS BASE IS INSTALLED.
- Secure the Mattress Base using 4 x 35mm bolts.
- Do not tighten completely.
- Attach the remaining Side Panel between the End Panels using 4 x 60mm bolts.
- Tighten all bolts until firm. Do not over-tighten bolts. Over-tightening bolts can cause panels to crack.
- Rotate the Cot so it is upside down on the floor.
- Attach 2 x Footboard End Panels to 1 x Footboard Side Panel using 4 x 30mm bolts.
- Attach the remaining Footboard Side Panel to another end of 2 x Footboard End Panels using 4 x 30mm bolts.
- Attach the assembled footboard base to the underside of the cot using 6 x 35mm bolts.
- Attach 1 x Leg to the outside of one Footboard Side Panel using 6 x 35mm bolts.
- Repeat for the remaining Leg.
- Carefully stand the cot upright. Check all bolts for firmness, but do not overtighten them.
Mattress Base Heights
Mattress base in High Position: The base height is set for when your baby is young and cannot sit up unaided.
Mattress base in Low Position: This is the normal position for an active baby who can sit up unaided.
To adjust Mattress Base Height
- Carefully lay the cot down on a Side Panel.
- Remove the 4 x Filler Bolts and Nuts for the lower base position on the End Panels.
- Remove 4 x 35mm Mattress Base bolts.
- Slightly loosen the 4 x connector bolts of one end panel in order to aid with this next step.
- Carefully slide the Mattress Base to the lower position and attach it with 4 x 35mm bolts.
- Refit 4 x Filler Bolts and Nuts to the upper Mattress Base Mounting holes to prevent possible finger entrapment.
- Re-tighten the end panel connector bolts.
- Carefully stand the cot upright.
The cot is now ready for use in low-base mode.
To assemble Cot Bed Rail
NOTE: Cot Bed Rail can only be used when Mattress Base is in Low Base Mode.
- Carefully lay the cot down on one Side Panel.
- Remove 8 x 35mm bolts connecting the Leg Assembly to the Side Panels.
- Remove 4 x 60mm bolts from the ends of the Side Panel.
- Carefully remove the Side Panel from the Cot.
- Replace the Side Panel with the Cot Bed Rail.
- Secure the Cot Bed Rail to the Cot End Panels using 4 x 60mm bolts.
- Secure the Cot Bed Rail to the Leg Assembly using 8 x 35mm bolts.
- Stand the Cot upright.
The cot is now ready for use in Cot Bed Mode.
HOW TO CARE FOR YOUR BEBE CARE COT
Cleaning
This product has been designed and developed with safety, comfort and functionality in mind. Please take the time to read this manual carefully before using this product and keep it in a safe place for future reference. To ensure the long-lasting use of your cot, wipe down with a damp cloth and use a mild soap solution if necessary. Do not use abrasive cleaners. Always store products in a clean dry place.
Maintenance
Always check parts regularly for tightness of screws, nuts, and other fasteners tighten or replace if required. To maintain the safety of your cot, seek prompt repairs for bent, torn, worn or broken parts. Use only those parts and accessories approved by CNP Brands. If you have any difficulties in assembling the cot, please contact our Service Department. In Australia, contact CNP Brands at 1300 667 137, in New Zealand contact Wainhouse Distribution on 0800 567 5000.
Warranty
For all warranty terms and conditions, please visit cnpbrands.com.au
ABOUT US
About CNP Brands
Currently, CNP Brands boasts one of the most diverse brand portfolios with a combination of company-owned brands and distribution agreements. Our own brands, including Childcare, have gone from strength to strength in recent years. Childcare, and our premium brand Bebe care, demonstrate our commitment to quality and continuing investment in product development.
Distributed in Australia by CNP Brands 82 Maribyrnong Street, Footscray, VIC, 3011 Customer Service 1300 667 137
- W: www.cnpbrands.com.au
- E: info@cnpbrands.com.au
- F: www.facebook.com/CNPBrands
- I: @cnp_baby
Distributed in New Zealand by Wainhouse Distribution
- ADDRESS: 2-6 Argyle St, Morningside, PO Box 41-014, St Lukes, Auckland, New Zealand
- Customer Service: 0800 567 5000
- E: helpline@wainhousedist.co.nz
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>