BLUETTI AC180P Portable Solar Power Station User Manual

BLUETTI AC180P Portable Solar Power Station

Warning

1. Charge the unit before first use.
2. Do not use solar panels with open circuit voltage higher than 60V. Solar input voltage range for the unit is DC 12V~60V.
3. Charge the unit when the SoC drops below 5%. If the SoC drops to 0, power off the unit and charge it for at least 30mins before restarting.
4. The unit is for off-grid use only. Do not connect its AC output to the grid.
5. If not used for more than 3 months, charge the unit to 40%~60% SoC and store it with the power off. For optimum battery life, discharge and charge the unit every 3 months.
6. This product must be grounded before operation.
   Connect a grounding cable (recommended 14AWG（1.5mm2）/105oC/yellow-green color) to the grounding terminal of AC180P. Fasten the grounding screw (M5*10) to fix the cable.

Thank You
Thank you for making BLUETTI a part of your family.
From the very beginning, BLUETTI has tried to stay true to a sustainable future through green energy storage solutions for both indoor and outdoor use while delivering an exceptional eco-friendly experience for our homes and our world. That’s why BLUETTI makes its presence in 70+ countries and is trusted by millions of customers across the globe.

Safety Instructions

Read this manual for instructions on the proper use and safety information for the unit. Follow the warnings and instructions marked on the unit and its accessories.
Pay attention to the “Instruction”, “Caution”, “Warning” and “Danger” symbols in this  manual, and follow the instructions carefully to avoid injury or damage.
The Safety Requirements provided herein are for illustrative purposes that include but are not limited to those listed in this manual. Actual operation shall comply with all applicable safety standards.
If you have any questions, feel free to contact BLUETTI support or your local BLUETTI dealers.

General Safety

• Always operate or store the unit in the conditions specified in this manual.
• The installation and ambient conditions must comply with the regulations in the relevant international, national or regional standards.
• Unauthorized disassembly, alteration of the equipment or modification of the software code is not allowed.

BLUETTI shall not be liable for the following circumstances:

• Equipment damage caused by force majeure, such as earthquake, fire, storm, flood, mudslide, etc.
• Damage or loss during transportation.
• Damage caused by storage conditions that do not meet the requirements specified in this manual.
• Damage to the hardware or data of the equipment due to customer negligence, improper operation or intentional damage.
• Damage to the system caused by a third party or the customer, including handling and installation that does not meet the requirements specified in this manual.
• The product is intended for use with audio/video, information and communication technology equipment only.
• This product is not suitable for providing electrical service for equipment and machines that are highly dependent on the reliability of electrical power supply and that involve personal safety, such as atomic energy, aviation, medical, etc. Poweroak will not be held responsible for any personal safety accidents, fire accidents, equipment failures, etc. caused by using this product to supply power to the above equipment and machines.
• Damage caused by adjustment, alteration or removal of identification marks.

To avoid danger, please regulate the operation in the following manner：

• Do not install, use and maintain the unit in adverse weather conditions such as lightning, rain, snow and strong breezes (including but not limited to handling and operating the unit, plugging and unplugging signal connections to outdoor facilities, working at height, outdoor installations, etc.).
• Always turn off the power source before starting any electrical work.
• Do not clean the unit with water.
• Do not disassemble, modify, tamper with or repair the unit on your own.
• Regularly inspect the unit and its accessories for damage or deterioration.
• Use a tester to check for the presence of dangerous voltage before touching any conductor or terminal.
• If the unit’s shell is cracked during transportation or use, do not use it and contact BLUETTI support or your local BLUETTI dealers.
• Use a dry powder extinguisher if the unit catches fire.
• In case of fire, EVACUATE the building or affected area immediately, activate the closest FIRE ALARM system and CALL 9-1-1 or your local emergency phone number.
• Use genuine cables and accessories provided by BLUETTI.
• Keep the unit away from heat sources or high temperatures, and do not expose it to direct sunlight.
• Do not store the unit with flammable liquids, gases, or explosive materials.
• Make sure the area where you are using the unit is well ventilated and spacious.
• Do not block or cover the vents of the unit as this may cause irreversible damage to it.
• Use the unit for its intended purpose and avoid stacking objects on top of it during storage or use.
• Do not move the unit during operation as the vibrations and shocks associated with movement may cause damage to the internal hardware.
• In case of malfunction, turn off the unit immediately and contact BLUETTI support or your local BLUETTI dealers if this manual cannot adequately explain the malfunction to you.
• Do not place the unit on an unstable or inclined surface.
• Do not insert foreign objects into any port and vent of the unit.
• Keep away from children and pets.
• This product must be grounded before operation.
  Connect a grounding cable (recommended 14AWG（1.5mm2）/105oC/yellow-green color) to the grounding terminal of AC180P. Fasten the grounding screw (M5*10) to fix the cable.

The symbol is intended to alert you to read the instructions before operating and maintenance in the literature accompanying the product.

• The product is intended for use with audio/video, information and communication technology equipment only.
• Connect the equipment to a socket-outlet with earthing connection by means of a power cord.
• The socket-outlet shall be installed near the equipment and shall be easily accessible.
• Disposal of a battery into fire or a hot oven, or mechanically crushing or cutting of a battery, that can result in an explosion.
• Leaving a battery in an extremely high temperature surrounding environment that can result in an explosion or the leakage of flammable liquid or gas
• The battery subjected to extremely low air pressure that may result in an explosion or the leakage of flammable liquid or gas
• Attention should be drawn to environmental aspects of battery disposal.
• Please refer the information on exterior bottom enclosure for electrical and safety information before installing or operating the apparatus. Please refer the information on exterior bottom enclosure for electrical and safety information before installing or operating the apparatus

Legal and Regulatory Requirements

• The transportation, wiring and maintenance shall comply with all applicable laws, regulations and standards.
• User-provided materials and tools required shall meet the requirements specified in applicable laws, regulations and relevant standards.

Handling
Use mechanical assistance as needed (e.g. trolleys and adjustable height workbenches).

Recommended number of people based on the weight of product

Storage and usage

• When not using the unit for over 3 months, charge it to 40% to 60% SoC to keep it in optimal condition.
• Before storing the unit, power it off and remove all electrical connections from it.
• Store the unit in a cool and dry place. The ideal temperature range is 1o0C to 300C. The unit can be safely charged and discharged at temperatures of -200C to 400C. However, it’s NOT recommended to store the unit in harsh temperatures for extended periods of time.
• Fully cycle the unit every 6 months to maintain the battery’s health.

If the SoC drops to 0 (during operation or upon startup), take the following actions to safely restart the unit:

1. Shut down immediately.
2. Charging within 48 hours.
3. Battery should be kept at an ambient temperature of 50C to 350C for 24 hours before charging.

It is recommended to charge the unit via an AC source. If charging via solar energy, ensure that your solar system provides an output of more than 100W.
BLUETTI shall not be liable for any equipment damage caused by the violation of above instructions.

What’s In The Box

Standard Packaging

Optional
(Available on official BLUETTI website)

Product Overview

Diagram
BLUETTI AC180P is a portable power station with 1800W pure sine wave inverter and 1440Wh LiFePO4 battery, perfect for camping, van life and more. In addition to 2 AC output ports and 5 USB ports (4 USB-A and 1 USB-C), it also has a 12V/10A cigarette lighter port for your vehicle devices and a wireless charging pad to run compatible electronics, your phone, headphone, Bluetooth speaker, just to name a few. As for recharging, AC180P takes up to 1440W AC input and 500W DC input, so you’re able to fully charge it in a few hours. It also supports BLUETTI app control – with the Bluetooth connectivity, you can monitor everything that’s happening inside and optimize your power usage to your preference.

1. DC Input
2. DC Power Button
3. LCD Screen
4. Power Button
5. AC Power Button
6. Wireless Charging Pad
7. AC Output
8. Grounding Pole(Grounding screw: M5*10)
9. AC Input Fuse
10. AC Input
11. Cigarette Lighter Port
12. USB-C Port
13. USB-A Port

Specifications

Discharging Temperature

| -20°C～40°C (35°C～40°C: @1500W Max.)

-4°F~104°F (95°F~104°F: @1500W Max.)

(When SOC is 100%, the discharge power at 35°C~40°C can be greater than 1500W, but it may trigger over temperature protection)

Storage Temperature| -20oC～40oC/-4°F~104°F
Working Humidity| 10%～90%
AC Output
Power| 1800W in total
Voltage| 100VAC| 120VAC| 220VAC| 230VAC
Current| 18A| 15A| 8.2A| 7.8A
Frequency| 50/60Hz
DC Output
Cigarette Lighter Port| 12VDC/10A

USB-A

| USB-A：5VDC/3A 15W in total USB-A：5VDC/3A 15W in total
USB-C (Type-C)| 5/9/12/15/20VDC, 3A; 20VDC, 5A (Built-in eMarker chip)
Wireless Charging| 5W/7.5W/10W/15W
AC Input
Voltage| 100VAC| 120VAC| 220VAC| 230VAC
Max. Current| 15A| 15A| 10A| 10A
Frequency| 50/60Hz

UPS

| Switching time ≤20ms

Test the function before use to avoid risk of data loss.

Power| 1440W Max. @10oC～30oC/50°F~86°F
DC Input
Interface| DC7909
Power| 500W/10A Max.
Voltage| 12V-60VDC

Operation

Buttons
BLUETTI AC180P has PWR button, AC power button and DC power button.

Power ON/OFF

• Press the PWR button to start the AC180P. When AC180P is on, press this button to turn on/off the LCD screen. Press and hold the button for more than 2 seconds to turn off the AC180P.
• Press the DC power button to turn on/off the DC output (cigarette lighter, USB, wireless charging).
• Press the AC power button to turn on/off the AC output.

Settings

• Setting mode: When the screen is on and the AC output is off, press and hold the AC and DC power buttons for about 2 seconds to enter Setting mode.

• Frequency switching: The current output frequency (50Hz/60Hz) is displayed in the lower right corner of the screen. Under Setting mode, press the AC power button to switch the frequency.

• Power Lifting mode: The Power Lifting mode is disabled by default. To enable it, press and hold the AC power button for about 2s in Setting Mode, or turn it on directly in the BLUETTI app. When enabled, the icon is displayed on the screen.In this mode, the AC180P can run high drain pure resistive loads* (≤2700W) while its rated output power remains 1800W.
  Note: The Power Lifting mode is not available when charging AC180P via an AC source like a wall outlet or generator. The AC source will bypass the inverter and supply power directly to connected AC loads.

• Any other devices consisting of heating elements only.

• Grid Enhancement mode: By default, the Grid Enhancement mode is disabled. Please turn it on directly in the BLUETTI app. This mode ensures that the AC180P has a stable and continuous AC input, as it allows AC180P to adapt to voltage fluctuations and waveform distortion of an AC source.

• Note: Turn off the Grid Enhancement mode when using AC180P as a UPS. In this mode, the UPS takes longer to switch over and may be unable to provide instant emergency power to connected devices.

• WARNING: This is a category C2 UPS product. In a residential environment, this product may cause radio interference, in which case the user may be required to take additional measures.

• ECO mode: When operating on ECO mode, the AC/DC output will automatically turn off if the AC180P is bearing low or no load for a while.
  When enabled, the ECO icon is displayed on the screen. Under Setting mode, press the DC power button turn it

• Press the AC and DC power buttons at the same time to exit Setting mode.
  Note : If you do not perform any operation in 1 minute, AC180P will exit Setting mode automatically and no changes will be saved.

• Check the error code: Press the AC and DC power buttons at the same time for about 2 seconds, and then hold the AC power button to check the current error code (e.g. E001).

LCD Screen

1. DC Input
2. Bluetooth
3. Wireless charging
4. Fan
5. ECO Mode
6. Turbo charging
7. Low voltage alert
8. Input power
9. Battery capacity
10. Output power
11. AC frequency
12. Temperature anomaly alert
13. Short circuit alert
14. Overload alert
15. Remaining time indicator
16. Power Lifting mode
17. AC indicator
18. DC indicator
19. AC input connected

Charging
AC180P supports four charging methods: AC, solar, car(cigarette lighter) and generator.

AC Charging (Wall Outlet)
Simply plug the AC180P into the standard wall outlet and start charging.

AC180P supports Turbo/Standard/Silent charging modes. It’s set to standard charging by default, while the Turbo and silent modes can be enabled in BLUETTI app. BLUETTI’s AC charging mode guide is as follows:

1. Turbo charging comes in handy when you need AC180P to be replenished in short time.
2. Standard charging is more friendly to AC180P’s battery.
3. Silent charging gives you quiet, low-power operation for long battery life.

Solar Charging
Connect the solar panels (in series or parallel) to AC180P via the solar charging cable.

Note : Please make sure your solar panels comply with:
Voc: 12V-60V Input Current: 10A Max. Input Power: 500W Max.

Warning : The open circuit voltage of solar panels cannot exceed 60V, otherwise it will damage the device(Note:It’s not covered in the warranty)

Car Charging
Connect the AC180P to vehicle’s 12V/24V cigarette lighter port via the car charging cable.

Warning : Cigarette lighter must be completely plugged in, otherwise it may cause safety risks.

Generator Charging
Connect the AC180P to generator via the AC charging cable.

Discharging
The operation time of AC180P is subject to many factors, such as ambient temperature, discharge rate, battery capacity, altitude, load characteristics, etc.

AC Output
AC180P has 4 AC output ports (2 ports for EU version), providing a total of up to 1800W AC power. It also can handle a surge of 2700W.

DC Output

• 12V/10A cigarette lighter port
• USB-C (PD 100W)
• USB-A (30W in total, 15W Max.)
• Wireless charging pad (15W Max.)

Estimated Operation Time
Depending on the connected power loads, there are two different scenarios to calculate the operation time of AC180P.

• If the AC180P is applied to a high power load, such as a 600W product.
  Operation time (estimated) = Battery capacity (Wh) × DoD × η ÷ (load power)

• If applied to a small power load like a 40W product.
  Operation time (estimated) = Battery capacity (Wh) × DoD × η ÷ (load power +self-con-sumption of AC180P)

Note:

1. The self-consumption of AC180P is about 15W.
2. Load power and operation time are measured in watts and hours.
3. DoD refers to depth of discharge. AC180P works at 90% DoD for longer battery life. η is the conversion efficiency of the inverter, which is larger than 85% for AC180P.
   E.g. If you have a 40W product, you can run it for about 20 hours.
   Operation time = 1440Wh x 90% x 85% ÷ (40W+15W) ≈20 hours.

Note: Low temperature and excessive loads could greatly impact the battery capacity and reduces its normal operation time.

BLUETTI App
Scan the QR code below or search “BLUETTI” in the App Store or Google Play to download the BLUETTI app.

AC180P supports Bluetooth connection. Once connected, the AC180P can be accessed and controlled on a mobile phone or other smart devices. For more details, please refer to BLUETTI APP INSTRUCTIONS.

FAQs

• How do I know whether my devices will work well with this product?
  Please evaluate the total constant load of your devices. If it doesn’t exceed the Max. output power of AC180P (1800W), you can use this power station to run your devices. Note: Some devices with built-in motor/compressor may start at 2-4 times the rated power, which can easily overload the AC180P.

• Can I use third-party solar panels to charge this product?
  Yes, you can. Make sure your solar panels have an open circuit voltage of 12V- 60V and have the MC4 connectors. Please do NOT mix different types of solar panels. Note: Time required for one full charge depends on weather condition, the sunshine intensity and the angle of solar panels.

• Can it charge and discharge at the same time?
  A: Yes. It supports pass-through charging. AC180P comes with the premium LiFePO4 battery and proprietary Battery Management System to ensure that it can charge and discharge at the same time.

• What is ECO mode and can I turn it off?
  ECO mode helps save power, and you can turn it on or off on the screen. When operating on ECO mode, the AC/DC output will automatically turn off if the AC180P is bearing low or no load for a while. You can set the power threshold of AC output and DC output to 15-30W /5-10W, respectively, for 1, 2, 3, or 4 hours.

• Why is the charging power often too low?
  AC180P has a built-in intelligent BMS that automatically adjusts the charging power in response to the battery temperature and SoC, thus protecting the battery and extending its service life.

• Can I make the AC180P less noisy when charging?
  Yes. Select “Silent” for AC charging in the BLUETTI app. Please refer to 4.3.1 AC Charging for more details.

• When should I use the Grid Enhancement mode?
  This mode is handy when charging the AC180P via an unstable AC source, such as an unreliable grid or generator.
  E.g. If you change the generator’s output while charging the AC180P, the voltage dip will also cause the charge to fail.

Troubleshooting

devices is too high.
E068| Cigarette lighter overtemperature| Wait a few minutes and try again.
E085| Charging temperature too high| Wait for the battery to cool down before charging.
E086| Charging temperature too low| Recommended charging temperature: 0oC~40oC.
E087| Discharging temperature too high| Wait for the battery to cool down before discharging.
E088| Discharging temperature too low| Recommended discharging temperature: -20oC~40oC.
E033| PV Input overvoltage| Ensure the PV input voltage is in the range of 12V~60VDC.
Others|  |

Contact BLUETTI technical support.

Abbreviations

• MPPT: Maximum Power Point Tracking
• SoC: State of Charge
• UPS: Uninterruptible Power Supply
• AC: Alternating Current
• DC: Direct Current
• PV: Photovoltaic (Solar Panels)
• DoD: Depth of Discharge

For more information, please visit:

SHENZHEN POWEROAK NEWENER CO., LTD.
Add: F19, BLD No.1, Kaidaer, Tongsha Rd No.168, Xili Street,
Nanshan, Shenzhen, China

After-sales address in EU: Lise-Meitner-Strasse 14, 28816 Stuhr, Germany
After-sales address in UK: Unit 2 Northgate, Bolsover Busines Park, Woodhouse Line, Chesterfield England S44 6BD

Company: POWEROAK ENERGY UK CO.,LTD
Address : Unit 2 NorthGate, Bolsover Business Park, Woodhouse Lane Chesterfield England, S44 6BD
Mail : poweroak.eu@bluetti.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>