Pavezo 14951 Handheld High Pressure Shower Head Installation Guide

: June 14, 2024
: Pavezo

Table of Contents

Pavezo 14951 Handheld High-Pressure Shower Head
SPECIFICATIONS
INSTALLATION
TROUBLESHOOTING
MAINTENANCE
References
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Pavezo 14951 Handheld High-Pressure Shower Head

Specifications

Product Name: High-Pressure Shower Head
Model Number: 14951
Body Material: ABS+304 Stainless Steel
Filter Aging: 3-5 Months
Filter Material: Chlorgon logic, Alkaline Ball, Calcium Sulfite, Medical Stone

Installation

Step 1: Tape the threads of the shower arm

Unscrew your previous showerhead from the shower arm threads.
Tape the threads of the shower arm with Teflon Tape. Please stretch the Teflon tape as tightly as possible to make it fit closely with the threads.

Step 2: Connect the bracket with the shower arm

Grab the Holder rotate it clockwise onto the shower arm and tighten it by hand as tight as possible. Note that the white plastic O-ring on the bracket should be open, not broken.
If you want to adjust the angle of the Bracket, keep grabbing the Holder and rotate it clockwise to the desired position. Do not rotate the Cylindrical Ring during the process, as it has been tightened by the machine.
In some rare cases, if you find that the Cylindrical Ring is loose, you could remove the bracket and tighten the Cylindrical Ring. If you are unable to tighten it, contact customer service for assistance. Note that using hardware tools may damage this part.

Step 3: Connect the hose to the bracket and showerhead

Make sure there is a washer on both sides of the hose.
Connect the CONICAL NUT to the shower head and the HEX NUT to the bracket. Note that the two different sides of the hose have different shapes, so do not mix them up.
We have already included washers in the hose before packing. However, if you can’t find them, you can use the additional washers provided.

Step 4: Installation Checkout

Please ensure that all coupling nuts are tightened. Hold the whole bracket by hand and rotate the ball joint to adjust the angle as needed. Then turn on the main water supply and check for leaks.
If you find any water leaks, please double-check that you followed steps 1-3 and that the installation was completed according to the instructions.
For installation video instructions, you can search “Pavezo shower head” or visit https://youtu.be/KVXnz1ju2y0.

Troubleshooting

Q1: Why does it leak?

A1: There might be an improper installation leading to leakage. You can try to fix it by following these steps:

If the hose is leaking, make sure to correctly place the black washer on both ends of the hose to prevent leaks.
If the shower arm is leaking, please refer to Step 1 of INSTALLATION.
If the bracket is leaking, follow these steps:
Screw the cylindrical ring out of the other part of the bracket.
Install the white O-ring (make sure it is open, not broken).
Take out the brass swivel ball joint, but do not remove the white O-ring.
Place the brass swivel ball joint into the cylindrical ring, then tighten the other part of the bracket to the cylindrical ring.

SPECIFICATIONS

Product Name: High-Pressure Shower Head
Model Number: 14951
Body Material: ABS+304 Stainless Steel
Filter Aging: 3-5 Months
Filter Material: Chlorgon lonic,Alkaline Ball,Calcium Sulfite,
Medical Stone

INSTALLATION

Step 1: Tape the threads of the shower arm

Unscrew your previous showerhead from the shower arm, then wrap 2-3 turns of (E)Teﬂon Tape around the shower arm threads.
(Please stretch the Teﬂon tape as tightly as possible to make it ﬁt closely with the threads.)

*Step 2(IMPORTANT AND CHALLENGING PART): Connected the bracket with shower arm**

Please grab the ”Holder” and rotate clockwise onto the shower arm and tighten it by hand as tight as possible.
- (Note: The white plastic O-ring on the bracket should be open, not broken.)
If you want to adjust the angle of the Bracket, please keep grabbing the ”Holder” and rotate it clockwise to the desired position.
(Please DON’T rotate the “Cylindrical Ring” during the process, as it has been tightened by the machine.)
- In some rare cases, if you ﬁnd that the “Cylindrical Ring” is loose, you could remove the bracket from the thread and then tighten it by rotating the “Cylindrical Ring” clockwise with your hands.
- If you encounter difficulties, you could ask a strong person for help.
- (Note: Using hardware tools may damage this part.)

Step 3: Connect the hose to the bracket and showerhead

Make sure there is a (C)washer on both sides of the hose.
Next, connect the CONICAL NUT to the (A)shower head and the HEX NUT to the (B)bracket.
(Note: Please don’t mix up the two different sides of the hose, which have different shapes.
We have already included washers in the hose before packing. However, if you can’t ﬁnd them, you can use the additional washers provided.

Step 4: Installation Checkout

Please ensure that all coupling nuts are tightened, hold the whole bracket by hand, and rotate the ball joint to adjust the angle as needed. Then turn on the main water supply and check for leaks.
(Note: If you ﬁnd any water leaks, please double-check that you followed steps 1-3 and that the installation was completed according to the instructions.)

Installation Method -Video

Search “Pavezo shower head” OR “ https://youtu.be/KVXnz1ju2y0
https://amz.run/6RtR

TROUBLESHOOTING

Q1: Why does it leak?

A1 : There might be an improper installation that leads to leakage. You could try to ﬁx it in these ways below:
a. If the hose is leaking, make sure to correctly place the black washer on both ends of the hose to prevent leaks.
b. If the shower arm is leaking, please refer to Step 1 of INSTALLATION.
c. If the bracket is leaking, it might be due to the white plastic O-ring becoming loose during transit. To ﬁx this, please reinstall the bracket by following the steps below.

Q2: Why can’t the showerhead be held onto the bracket?

A2: Please review Step 2 of the installation instructions again, you could try taking the bracket off from the thread and tightening it by rotating the Cylindrical Ring” clockwise very tightly by hand. If you have difficulty, you can ask for assistance from someone who is strong.

Q3: The water pressure seems too low. Is there any way to improve?

A3: Leaky, corroded, and clogged pipes might lead to low water pressure in the shower.
Firstly, please ensure that the shower and hose are properly connected;
Secondly, clean the showerhead with a vinegar/water solution (see MAINTENANCE section)
While household water pressure can vary depending on factors such as ﬂoor level and other circumstances, even if the pressure is at the minimum range of 14.2psi/1kg/0.98bar, our showers can still be used, although the water pressure effect may be relatively weak.

Q4: Why doesn’t the PAUSE mode shut off the water completely?

A4 : Considering the internal pressure balance, the pause mode will not completely shut off the water.
This pause mode is an energy-saving feature that conserves water while maintaining the desired water temperature.

MAINTENANCE

To maintain optimal performance, it is necessary to clean your shower head when mineral deposits start to accumulate on the spray openings. Gently rub the rubber nozzles on the face of the showerhead to dislodge any buildup.
For more stubborn deposits, remove the showerhead and soak it face down in 1-2 cups of white vinegar (only use white vinegar) for approximately 2-3 hours.
The ﬁlter element has a lifespan of around 3-5 months, so it is recom-mended to replace it regularly to ensure maximum effectiveness.

WARNING

It is strictly prohibited to set the showerhead to Power Jet or Wide Fan mode when it is closed and placed on the bracket. Doing so may cause the water column to hit the ceiling or lamp and cause damage when it is opened again.
To avoid the water column in Power Jet or Wide Fan mode from injuring anyone, it is recommended to keep the showerhead facing down when turning on the water valve switch, and then adjust the modes.
Regarding installation conﬁrmation, if there is no leakage from each component, the installation is considered complete. Do not overtighten any parts using hardware tools.