SITISFI Led Emergency Light With Battery Backup Photocell Sensor Instruction Manual

SITISFI Led Emergency Light With Battery Backup Photocell Sensor

Product Information

Specifications

Package Contents:

• Emergency Lighting – Quantity: 1
• Hardware Kit – Quantity: 1

Warnings and Cautions
IMPORTANT SAFEGUARDS READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. Review the diagrams thoroughly before beginning.
2. All electrical connections must be in accordance with local codes, ordinances, and the National Electric code.
3. Disconnect power at fuse or circuit breaker before installing or servicing.
4. Do not mount in hazardous locations, or near gas or electric heaters.
5. Do not let power cords touch hot surfaces.
6. Equipment should be mounted in locations and at heights where it will not be subjected to tampering by unauthorized personnel.
7. The use of accessory equipment not recommended by the manufacturer may cause an unsafe condition.
8. Do not use this equipment for other than intended use.
9. All servicing should be performed by qualified personnel only.
10. Allow battery to charge for 24 hours before first use.
    SAVE THESE INSTRUCTIONS

User Instructions

• Two-color function indication
• LED Light
• Cable outlet
• Test button

Mounting Instructions

NOTE: First turn off electricity.

1. Remove cover from fixture with a screwdriver.
2. Select working mode.
3. ELECTRICAL CONNECTIONS: Make the proper supply wire connections. Connect L and N to building power supply.
4. Pull out all AC wires from the back of the fixture or top of the fixture for mounting. (J-box not provided)
5. Restore power and press the test button. AC light will turn off.

Function:

1. When AC connected, the green indicator is on.
2. For normal lighting use, the fixture can be configured for automatic operation by the built-in daylight photo.

FAQ (Frequently Asked Questions)

• How long does it take for the battery to charge before first use?
  The battery should be allowed to charge for 24 hours before first use.

Package Contents

1. Emergency Lighting x1
2. Hardware Kit x1

Warnings and Cautions
IMPORTANT SAFEGUARDS
READ AND FOLLOW ALL SAFETY INSTRUCTIONS

1. Review the diagrams thoroughly before beginning.
2. All electrical connections must be in accordance with local codes, ordinances and the National Electric code.
3. Disconnect power at fuse or circuit breaker before installing or servicing.
4. Do not mount in hazardous locations, or near gas or electric heaters.
5. Do not let power cords touch hot surface.
6. Equipment should be mounted in locations and at heights where it will not be subjected to tampering by unauthorized personnel.
7. The use of accessory equipment not recommend by the manufacturer may cause an unsafe condition.
8. Do not use this equipment for other than intended use.
9. All servicing should be performed by qualified personnel only.
10. Allow battery to charge for 24 hours before first use.
    SAVE THESE INSTRUCTIONS

User Instructions

1. Two-color function indication
2. LED Light
3. Cable outlet
4. Test button

Mounting Instructions

NOTE: First turn off electricity.

Mounting

1. Remove cover from fixture with a screwdriver

2. Select working mode.

3. ELECTRICAL CONNECTIONS
   Make the proper supply wire connections.
   Connect L and N to building power supply.

4. Pull out all AC wires from the back of the fixture or top of the fixture for mounting. (J-box not provided)

5. Restore power and press test button. AC light will turn off.

Function:

1. When AC connected, the green indicator on.
2. For normal lighting use, the fixture can be configured for automatic operation by the built-in daylight photo sensor, or can be switched through an external switch. For battery backup models the fixture will illuminate from battery power on loss of normal AC, regardless of the photo sensor or wall switch operation.
3. For photo sensor operation, connect the jumper between terminals 1 and 2 (Pic2) and slide the slide switch (Pic4) to the Photo Sensor position. The photo sensor will turn the fixture on when the ambient lighting <10 Lux, and off when the ambient lighting >30 Lux.
4. For an external switch: remove the jumper between terminals 1 and 2(Pic3), and slide the slide switch (Pic4) to the Wall Switch position. The external switch connections must be fully isolated from any other circuitry

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>