CUCKOO CP-MN031 Water Purifier User Manual
- June 17, 2024
- CUCKOO
Table of Contents
CUCKOO CP-MN031 Water Purifier User Manual
Warnings for Safe Use
- Please comply with the ‘Warnings for Safe Use’ to ensure safe and proper use of the product and prevent accidents and dangerous situations.
About the Power Supply
- Do not bend, tie or pull the Power Cord by force.
- If unplugging the product, make sure to hold the Power Plug and not the Power Cord.
- In case of water leakage or cleaning, please unplug the 1device first.
- Make sure the power cord is not under a heavy object or near sharp objects. Take special caution to ensure that it is not damaged by pets.
- Please also unplug the product before inspection, repair or replacement of its parts.
- Stop using the product if the Power Cord or the Power Plug is damaged or the Power Outlet is shaking, and contact our Customer Service Center.
- Wipe off any foreign substance on the Power Plug with a dry cloth.
- Do not use other than the following: U.S.: 120V / 60Hz; Europe: 220V / 50Hz; U.K: 240V / 50Hz; China: 220V / 50Hz; and Vietnam: 220V / 60Hz.
- If putting in or pulling out the Power Plug, first remove moisture on your hands and then put in or pull out the Power Plug by holding the Power Plug.
- If water enters the power supply area, unplug the produ1ct and dry it completely before use.
- In case of a long period of non-use, pull out the plug and keep it safe after closing the Tap Water Supply Valve and emptying the remaining water inside the tank.
Installation Guide
- Do not place the purifier in humid or dusty areas.
- Do not install the product near the bathroom.
- Do not place it in a bumpy or slanted area Please avoid placing it on a rug, cushion or laminated floor.
- Please make sure to install the device in clean areas.
- Avoid direct sunlight and high temperature.
- Make sure that the length of water supply tube, doesn’t exceed 5 m from the Tap Water Supply Valve.
- Do not place any heating device, such as a microwave oven, electric oven or toaster, or inflammables, such as candles, gas containers, and lighters on top of the product.
- Be careful with the water leaking into the device.
- Unless they are supervised, the device must not be used by those (including children) with reduced, physical, sensory and mental abilities or who do not have the required experience and knowledge.
- Do not place it in an area where there’s a risk of gas leak or near a cooling or heating device.
- Make sure to supply the tap water and install the Tap Water Supply Valve towards the cold water pipe.
- Do not place the device outside or in an area that falls below o;c.
- After completing installation, please keep it clean and well-maintained.
- If installing the product to the sink faucet, always use cold water or purified water. (Do not use hot water.)
- Do not place chemicals, water bottles or small metal materials on top of the product.
- Do not disassemble or remodel the product .
- After installing, please make sure that tubes arid hoses are firmly connected and that there is no leakage .
About How To Use
- If you find that it is leaking or there is a pool of water around the product, close the Tap Water Supply Valve first, tum it off and then unplug the product After that, please contact our Customer Service Center.
- Do not pull the Power Cord or hose, nor grab the faucet when moving the product.
- If you smell burning or see smoke arising from the device, unplug it immediately and close the Tap Water Supply Valve. After that please contact our Customer Service Center.
- Do not put plates or any metallic materials on the top of the product
- Make sure the cover for replacing a filter of the product is completely closed before use.
- If left idle for a long time, please make sure the water ge,ts dispensed for about 10 minutes before using the device.
- Replace the filter according to the replacement cycle.
- Always use the genuine CUCKOO filters for the product.
- If you have not used the External Faucet for a long time,, it can be polluted.
- If reusing it, it will start dispensing after draining remaining water for about one to two minutes.
- Do not clean the product using benzene or thinner.
- While using the product, do not pull off the tube at the b1ack.
- Do not move the device while it’s operating.
- Please avoid using the dispensed water for filling a fish lbowl or an aquarium.
Part names
Water Purification Pipe Layout and Water Purification System
The 3-Stage Filtration System
- Featuring a multiple-stage filtration process, the water purifier can provide crisp-tasting, bottled-quality mineral water straight from your tap.
Helps filter out minute particles, invisible to the naked eye
- Using a non-CUCKOO filter or using a !J811Uine OJCKOO filter for a long time may result in diminished filter performance.
Matters To Check before Installation
Matters To Check before Use
-
Open the Tap Water Supply Valve.
► Tum the tap on first to check if the water is property supplied. After that, open the Tap Water Supply Valve. -
Plug in the product
► Check for water disconnection before plug-in. -
If it has been left idle for a long time or is newly installed, please leave it to drain for about 1 O minutes ..
-
Empty the tray on a regular basis.
How To Use
How To Set One Cup Quantity
-
Press the One Cup button for 3 seconds in Standby mode to set the quantity for One Cup.
-
Depending on the selected quantity, one or nr1ore of the following LEDs will be lit up: One Cup LED, Non-Stop
Flow LED, Button Lock LED, and Filter Replacement LED.(The default quantity is about 150cc.) -
Select your desired quantity for One Cup (about 130cc -190cc) by pressing the Outflow button.
* The quantity of dispensed water varies in accordance with Ille
place of installation. -
Select your desired quantity for One Cup ,:md press the One Cup button.
♦ If you press any other button than the Outflow or the One Cup button, it will be canceled and the product will return to Standby mode.
♦ If you fail to press any button for 20 seconds In the settings, it will be canceled and the product will return to Standby mode.
How to Set the Time for Non-Stop Flow
-
Press the Not-stop Flow button for 3 seconds in Standby mode to set the time for Non-Stop Flow.
-
Depending on the selected time, one or more of the following LEDs will be lit up: One Cup LED, Non-Stop Flow LED, Button Lock LED, and Filter Replacement ILED. (The default time is about 60 seconds.)
-
Press the Outflow button to select your desired lame for Non-Stop Flow (50 to 80 seconds).
-
Select your desired time and press the No1n-Stop Flow button.
♦ If you press any other button than the Outflow or the Non-Stop Flow button, it will be canceled and the product will return to Standby mode .
♦ If you fall to press any button for 20 seconds In the settings, it will be canceled and the product will return to Standby mode 8 .
How to Set Faucet Lighting
-
Press the One Cup and Not-Stop Flow buttons simultaneous~~ for 3 seconds in Standby mode to access the settings.
-
Depending on the selected status, the following LEDs will be In up: one Cup LED, Non-Stop Flow LED, Button Lock LED, and Filter Replacement LED. (The default setting is ON.)
-
Press the Outflow button to select the desired status.
-
Select your desired status and press the Button Lock button.
♦ If you press any other button than the outflow or the button lock button, it will be canceled and the product will return to standby mode.
♦ If you fall to press any button for 20 seconds In the settings, it will be canceled and the product will return to Standby mode.
How To Remove and Clean the Faucet
-
Hold the faucet and tum n clockwise to remove it.
-
After separation, wipe out the faucet inlet with a clean cloth.
-
Clean the separated faucet with running water.
(You may easily wipe out the dirt inside the faucet that you cannot reach by using a cotton swab, etc.) -
Wipe the faucet dry with a clean cloth.
-
Insert the faucet by turning n counterclockwise.
Expected Filter Replacement Cycle
-
The filter replacement cycle is set based on the amount of water filtered at home (1 OL per day), and the status of water supply may affect the cycle.
-
How to Reset Notification for Filter Replacement(* CP’-MN031)
• If a life of each filter is exceeded, the Filter Replacement LED will be illuminated.
• Press the [Filter Replacement] button to view the filter(s) that requires replacement.
After the filter(s} has been replaced, press the [Filter Replacement] button again to reset the cycle.
• When resetting a filter me, the Filter Replacement LED will be off.
Recommendations
- Filter Replacement Cycle
► After a close review of filters, It is carefully estimated period during which a filter is expected to display its proper performance. This is determined based on the amount of tap water filtered for drinking (1 DL per day for fourj. Thus the cycle shortens as the amount used goes up.
Please check before asking for Support~
► If you do not comply with this User Manual, the product may not work properly even if there is no malfunction. Please take the following measures accordingly if there is a problem with the product. If there is still a problem, please contact our Customer Service Center.
Asking for Repairs
It may not work properly due to worn out components that were continuously exposed to heat, moisture, dust and other pollutants.
Product Specifications
- Specifications and other details (exterior, design, and specifications) In this User Manual may be subject to change without prior notice for product Improvement.
- As this equipment has undergone EMC registration for household purpose (‘B’ class), this product can be used In any area and designed to be used mainly in a household.
- Manufacturer: CUCKOO HOMESYS Co., Ltd.
Dispute Solution for Consumers
On Our Service
-
Rights of our customers
Our customers have a precious light to receive a service for free for one year from the date of purchase when a malfunction has occurred during use of the product.
But, when a malfunction has occurred by the customer’s negligence or natural disaster, the customer can only receive billed service even within the period of free service. -
Responsibility for billed service (burden of expenses of the customer)
If a customer requests service and it comes under one of the following, the customer can receive a billed service Within the period of free service.
- If a malfunction has occurred as foreign substances (water, beverage, coffee, toys, etc:.) has been put Into the product
- If the product Is damaged and a malfunction on the functions has occurred as the pro1Juct had been dropped or due to an Impact
- If the exterior of the product Is damaged and/or deformed by an organic solvent such as thinner and benzene
- If a malfunction has occurred since a part or consumable, which are not a genuine CUCKOO ones, are used (adapter, filter, etc.). Purchase genuine CUCKOO parts and consumables at a designated Customer Service Center .
- If a malfunction has occurred since the wrong voltage had been supplied
- If a component is lost or damaged since the customer had arbitrarily disassembled thn product
- If a malfunction has occurred since a person who Is not a service engineer of a CUCKOO Customer Service Center has repaired or remodeled the product
- If a malfunction has occurred by a natural disaster 0lghtning, fire, damage from storm and flood, gas, damage from sea wind, earthquake, etc.)
- If a malfunction has occurred since the customer had not complied with the ‘Warnings for Safe Use’ In the User Manual QI you comply with the ‘Warnings for Safe Use,’ you can use the product for a long time.)
- If a malfunction has occurred because of any other mistake of the customer
We provide satisfying consultation and services concerning your complaints, suggestions, and recommendations upon receiving your troubled product model name, status, and contact information.
After reading this manual, keep it in a place easily accessible to the user for future reference.
This manual includes the warranty.
Caution: Please read this manual carefully to ensure safety and a longer product lifespan.
00383-1000A0 Rev.6