Zhong Shan TRD028H1Y Ceiling Fan Remote Control User Manual
- June 14, 2024
- ZHONG SHAN
Table of Contents
Zhong Shan TRD028H1Y Ceiling Fan Remote Control
LEARNING PROCESS
The Hand Held Remote Control is equipped with a learning ID function which has
code combinations to prevent potential interference from other remote units.
Step: 1. Install the batteries AAA 1.5V*2 PCS in transmitter. Within 30
seconds of turning the Receiver AC power ON, press the transmitter LEARN
button
Step: 2. Hold LEARN button about 3 seconds, once the receiver has detected the
ID, the light of ceiling fan will be blinking twice and the fan turn on low
speed. This will indicate the receiver has learned the ID that was previously
selected on the transmitter.( The 0/1 switch on the back of the transmitter is
in the “0” state, and it can be directly controlled without pairing. The 0/1
switch is in the “1” state, need to proceed learning.)
Note: After the AC power is on, do not press any other buttons on the transmitter before learning ok. Because if doing so will cause the procedure to fail.
After completing the steps above, you should be able to operate the ceiling
fan and light. If the ceiling fan is not responding to the transmitter, please
turn the power off to the receiver and repeat step 1 and 2.
Remove the batteries if not used for long periods of time to prevent damage to
the hand held remote. The batteries must be removed from the transmitter
before it is scrapped and the batteries shall be disposed of safety.
Light function select switch:
Slide the D/O switch, located in the battery compartment, to match the bulb
type in your fan.
“D”(DIMMER) for incandescent bulbs and “O”(ON/OFF) indicates compact
fluorescent bulbs (CFL). Use a small screwdriver or ballpoint pen to slide
firmly left or right.
FUNCTIONS OF TRANSMITTER
6. BREEZE: Control the fan to enter the natural wind state, and the digital
indicator light will run from bottom to top once and display “CB”， Long press
for 3 seconds and “CB” flashes 4 times, then the timing will be cancelled.
7. TEMPERATURE SETTING: +/- is the button of RGB manual switching, : RGB
automatic switching.
8. FAN TIMER：2, 4, 8 hours. Control the fan to enter the timing OFF, and the
digital display will display the current timing range. Press and hold for 3S,
the digital display will display “00”, and the timing will be cancelled.
9. SUMMER KEY: Long press for 3 seconds for setting forward airflow of the
ceiling fan. And the digital indicator light will run from bottom to top once
and display “do”.
WINTER KEY: Long press for 3 seconds for setting reverse airflow of the
ceiling fan. And the digital indicator light will run from bottom to top once
and display “UP”.
10. COLOR TEMP: Press button to switch the color.
FEDERAL COMMUNICATIONS COMMISSION INTERFERENCE STATEMENT
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
CAUTION:
To assure continued FCC compliance:
Any changes or modifications not expressly approved by the grantee of this
device could void the user’s authority to operate the equipment.
FCC ID：2AQZU-18046
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
FCC Warning
NOTE 1: This equipment has been tested and found to comply with the
limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications. However, there is no guarantee that interference will not
occur in a particular installation. If this equipment does cause harmful
interference to radio or television reception, which can be determined by
turning the equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
NOTE 2: Any changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
IC WARNING
This device contains licence-exempt transmitter(s) that comply with
Innovation, Science and Economic Development Canada’s licence-exempt RSS(s).
Operation is subject to the following two conditions:
(1) This device may not cause interference.
(2) This device must accept any interference, including interference that may
cause undesired operation of the device.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>