Honeywell T12323 LED Whistler Fir Slim Color Changing User Manual
- June 14, 2024
- Honeywell
Table of Contents
Honeywell T12323 LED Whistler Fir Slim Color Changing
Important Information
Read and save these instruction before use
CAUTION! ALWAYS UNPLUG YOUR TREE FROM ITS POWER SOURCE BEFORE ASSEMBLING OR DISASSEMBLING.
THANK YOU
Thank you for purchasing the 8ft Honeywell Whistler Fir Slim Color Changing
LED tree.
This tree assembles in minutes and is decorated with LED light sets. This tree
has 4 lighting options, Warm White Color Steady On, Multicolor Steady On,
Color Changing and off. These functions can be changed by using the control
box. For your convenience, it is equipped with a foot pedal switch for easy
illumination.
IMPORTANT SAFETY INSTRUCTIONS
When using electrical products, basic precautions should always be followed including the following:
READ AND FOLLOW ALL SAFETY INSTRUCTIONS.
- Do not use this product outdoors.
- This seasonal use product is not intended for permanent installation or use.
- Do not mount or place near gas or electric heaters, fireplace, candles or other similar sources of heat.
- Do not secure the wiring of the product with staples or nails, or place on sharp hooks or nails.
- Do not let lamps rest on the supply cord or on any wire.
- Unplug the product when leaving the house, when retiring for the night, or if left unattended
- This is an electric product not a toy! — To avoid risk of fire, burns, personal injuryand electric shock it should notbe played with or placed where small children can reach it.
- Do not use this product for other than its intended use.
- Do not hang ornaments or other objects from cord, wire, or light string. Hang ornaments only on the tree itself.
- Do not close doors or windows on the product or extension cords as this may damage the wire insulation.
- Do not cover the product with cloth, paper or any material not part of the product when in use.
- This product employs overload protection (fuse). A blown fuse indicates an overloador short-circuit situation. If the fuse blows, unplug the product from the outlet. Alsounplug any additional strings or products that may be attached to the product. Replace the fuse as per the user servicing instructions (follow product marking for proper fuse rating) and check the product. If the replacement fuse blows, a short-circuit may be present and the product should be discarded.
- This product is equipped with push-in type lamps. Do not twist lamps.
- This product has a polarized plug (one blade is wider than the other) as a feature to reduce the risk of electric shock. This plug will fit in a polarized outlet only one way.If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Do not use with an extension cord unless plug can be fully inserted. Do not alter or replace the plug.
- Read and follow all instructions that are on the product or provided with the product.
SAVE THESE INSTRUCTIONS.
PACKAGE CONTENT
Installation kit:
-
A. Top Section (1 set)
-
B Middle Section (1 set)
-
C Bottom Section (1 set)
-
D Tree Base (1 set)
-
E Screw (1 piece)
-
F Power cord with foot pedal switch (1 piece)
OTHER COMPONENTS
-
G. Fuse (2 pieces)
-
H Replacement lamp (8 pieces)
INSTALLATION
Note: Before you start to assemble your tree, please choose a location
near an electrical wall outlet. Place the tree stand on a level surface.
Please remove protective covers from the base of the pole from each section.
-
Unfold the tree base to a 90 degree angle.
-
Carefully insert bottom section (C) of tree into tree base and tighten the screw (see Fig. 1).
-
Insert the middle section (B) of the tree into the bottom section (C) (see Fig. 2).
-
Insert the top section (A) into the middle section (B) (see Fig. 3). Plug 1 On/off foot pedal switch A B Fig. 2 C Fig. 3 Tree base Fig. 1 side view Fig. 4 Fig. 5 D Plug 2 Note: There is a tree top connector on the top section (A).
-
Allow the branches to fall into place or gently pull branches up and out. When adjusting branches be sure that all wires are free of branch hinges (see Fig. 4).
-
Shape the branches. Starting with tips closest to the pole, shape one tip to the right, one to the left and one along the centre of the main stem. Repeat pattern for each 5. Allow the branches to fall into place or gently pull branches up and out. When adjusting branches be sure that all wires are free of branch hinges (see Fig. 4).
-
Plug the well-connected power supply cord plug 1 from the bottom section (C) into electrical outlet. The plug 2 is for tree top lights. Plug the power supply cord plug 2 branch (see Fig. 5). into electrical outlet. F Plug 3 Control box
-
Another way to light up the tree. Please note this tree comes with a power cord with on/off foot pedal switch (F) for easy illumination. Plug the plug 1 and plug 2 into the
-
Please note this tree comes with a control box for easy illumination and changing .
power cord with on/off foot pedal switch (F). Plug the plug 3 into the electrical outlet. functions. This tree is Color Changing, the 4 lighting options available are : -
Warm White Color Steady On,
-
Multicolor Steady On,
-
Color Changing and
-
Off.
TROUBLESHOOTHING
If any lights do not work on your pre-lit tree, please check the following before calling customer service:
-
If entire tree or a section of the tree does not light:
a) Make sure the end connector of the power cord is well connected to the bottom section (C).
b) Check that each section of the tree is well connected.
c) Check that there is power at the electrical outlet.
d) Check fuses in tree’s plugs and replace if necessary (see Replace the fuse below). -
If a strand of lights still does not work:
a) Check that all lamps are tightly fitted inside the lampholders and that no lamps are broken or missing. Replace any broken or missing lamps with replacement lamps provided (see Replace the lamp below). If all lamps are firmly in the lampholders, slightly twist the lamps from side to side to ensure proper connection.
b) If the lights still do not work, carefully remove each lamp one by one out of the problem light string. Pull the lamp AND plastic base straight out of lampholder. Do not twist lamps while removing from lampholders. Check the two wires at the bottom of the lampholder. Each wire should be aligned properly on the lampholder to ensure of the lampholder. Each wire should be aligned properly on the lampholder to ensure replace lamp with a replacement lamp (provided). -
If you are still experiencing problems with the tree, please contact us at 866-205-9854.
Loose branches
If a branch of the tree falls off, follow the steps below to reinstall it
with a spare bolt.
- Place the branch into the slot of the bracket.
- Insert a spare bolt through the hole and use diagonal pliers (not included) to crimp the bolt. (See Fig. A)
CAUTION! ALWAYS UNPLUG YOUR TREE FROM ITS POWER SOURCE BEFORE ATTEMPTING EITHER FUSE OR LAMP REPLACEMENT.
USER SERVICING INSTRUCTIONS
Replace the fuse:
A) Replace the fuse of power cord with foot pedal switch (1 replaceable 5
A, 125 V fuse is located in the plug):
Note: This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug.
- Grasp plug and remove from the receptacle or other outlet device. Do not
- Open fuse cover. Slide open fuse access cover on top of attachment plug Note: This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. fuse is located in the plug): unplug by pulling on cord. towards blades.
- Remove fuse carefully.
- Risk of fire. Replace fuse only with 5 Amp, 125 Volt fuse (provided with product).
- 5. Close fuse cover. Slide closed the fuse access cover on top of attachment plug.
- Risk of fire. Do not replace attachment plug. Contains a safety device (fuse) that should not be removed. Discard product if the attachment plug is damaged.
B) Replace the fuse of the power cord from the bottom section ( C) and plug 2:
- Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
- Open fuse cover. Slide open fuse access cover on top of attachment plug towards blades
- Remove fuse carefully.
- Risk of fire. Replace fuse only with 3 Amp, 125 Volt fuse (provided with product).
- Close fuse cover. Slide closed the fuse access cover on top of attachment plug.
- Risk of fire. Do not replace attachment plug. Contains a safety device (fuse)
Replace the lamp:
- Grasp plug and remove from the receptacle or other outlet device. Do not unplug by pulling on cord.
- Unlock the burned out LED lamp by lifting the hook.
- Pull lamp and plastic base straight out of lampholder.
- Replace lamp with only 3.0 Volt, 0.06 Watt, LED type lamp (provided with product). Always match the hook to the tab.
- Lock the hook of lamp base by pushing lock down into the tab.
CAUTION:
- To reduce the risk of overheating, replace burned-out lamps promptly. Use 3.0 Volt, 0.06 Watt LED lamps only. The LED lamp has polarity. Do not deliberately change the direction of the LED lamp in the lamp holder.
- Risk of fire. This product does not contain lamp shunts, which allow the product to operate if one lamp burns out. Replace lamps only with the spare lamps provided with this product.
If the new lamp base does not fit in lampholder, follow the steps below before step 4:
- a) Pull the reflector out.
- b) Remove the base of burned out lamp by straightening lamp leads and gently pull lamp out.
- c) Thread leads of new lamp through holes in old base with one lead in each hole
- d) After lamp is fully inserted into base, bend each lead up, like other lamps in the light set so that the leads will touch the contacts inside the lampholder (always match the long lead of new lamp to the hook of lamp base). e) Insert the reflector into the base.
- e) Insert the reflector into the base.
CAUTION
a) To reduce the risk of electric shock, use only with the power-supply
cord provided or with a cord set intended for indoor use.
b) Do not use a cracked, frayed, or damaged cord. Inspect the cord
periodically.
c) Do not abuse cord – Do not carry product by the cord or yank or pull
it to disconnect
d) Disconnect the product from the outlet when not in use.
e) Do not overload. Connect other lighting strings or tree toppers end-
to-end up to a maximum of 216 watts (1.8 Amps) total. Do not interconnect low-
voltage products.
USE AND CARE INSTRUCTIONS
a) Before using or reusing, inspect product carefully. Discard any
products that have cut, damaged, or frayed wire insulation or cords, cracks in
the lampholders or enclosures,
b) When storing the product, carefully remove the product from wherever
it is placed loose connections, or exposed copper wire.
to avoid any undue strain or stress on the product conductors, connections,
and wires.
c) When not in use, store neatly in a cool, dry location protected from
sunlight.
FCC STATEMENT
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Warning: Please note that changes or modifications of this product is not
expressly approved by the party responsible for compliance could void the
user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instruc ions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation. If this equipment does cause harmful interference to
radio or television reception, which can be determined by turning the
equipment off and on, the user is encouraged to try to correct the
interference by one or more of the following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected
- Consult the dealer or an experienced radio/TV technician for help.
MODEL NO. HW_T12323
STORAGE: Disassembled tree can be stored in its original box. Store tree in a cool, dry place where the temperature does not exceed 100°F (38°C).
ONE PLUG® U.S. Patents: US8,454,186, US8,454,187, US8,936,379, US9,044,056, US 9,140,438, US 9,179,793, US9,222,656, US 9,243,788, US 10,194,764, US 10,433,604, US 10,578,289, US 10,721,981, US 11,006,687, US 11,013,355, US 11,419,374. Other Patents Pending.
Customer Support
See for a complete list of patents. https://www.williscorporation.com/about.html#p6
TXUSA Corporation 1919 Akron Peninsula Road, Akron, Ohio 44313 866-205-985
Dongguan Newone Trading Co., Ltd.
1001 Room, No.273, Jinxiu Road,
Changan Town, Dongguan City,
Guangdong Prov., China
866-205-9854
customersupport_hw@willis.com.tw
Made in Cambodia
The Honeywell Trademark is used under license from Honeywell International
Inc.
Honeywell International Inc. makes no representations or warranties with
respect to this product.
This product is manufactured by
Dongguan Newone Trading Co.,Ltd.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>