Qimic WS-21006 Gimbal Stabilizer for Smartphones Selfie Stick Phone Tripod Instruction Manual

Model: WS-21006 1-AXIS GIMBAL

AFTER-SALES SERVICE

If you encounter any problem with our products (such as broken), our after- sales team will always be a superman around you to help you.
SupportEmail：qimic@aliyun.com

PACKAGE CONTENT

PRODUCT COMPONENTS

BLUETOOTH FUNCTION INTRODUCTION

1. Power button:
   Long press for 3 se conds to turn on or off.

2. Rotate button:
   Click once the phone holder rotates 90 degrees. Repeat the cycle,
   Click twice,the phone holder rotates 270 degrees.

3. Camera button:
   Click to start (end) taking photo/video. Long press to take continuous shooting. (if iPhone’s ”Use Volume Up for Burst” function is off, long press for video)

REMOTE CONTROL CONNECTION

Press the power button for 3 seconds, turn on the Bluetooth of the mobile phone, and select “QIMIC WS-21006”. If the match is successful, the green light will be solid on.
Remote Control and Stabilizer Connection Recovery (If the remote control cannot control the stabilizer)
Step 1: Turn on the stabilizer;
Step 2: When the remote control is turned off, press and hold the remote control “M” key while holding down the remote control power button until the remote control is turned on.
If the “Volume Key Function” of the system is changed in the phone camera options, please change it to the default value or “Taking Photos”. Otherwise, Bluetooth will not work properly.

HOW TO USE THE S TABILIZER MODE?

Step 1: Rotating clockwise to loosen the phone holder, and counterclockwise to lock the phone holder;
Step 2: Loosen the phone holder and turn on the stabilizer, the phone holder will automatically rotate to the initial position;
Step 3: Pla ce the phone in the center of the stabilizer;
Step 4: Click the “M” but ton on the remote control once to control the phone holder;
Step 5: Shake the handle left and right, phone holder will keep horizontal or vertical;
Step 6: The phone selects the “Video” mode. After double-click the “M” button on the remote control, the phone will automatically rotate and start video
Step 7: Open the tripod, then push the rocker up to place the tripod on a flat sur face. recording;(Inception Mode)

If the stabilizer is turned on without load or the limit is not released, the stabilizer will automatically turn off after 15 seconds.

HOW TO CHARGE THE S TABILIZER/REMOTE CONTROL?

Stabilizer/Remote Control:

Plug the Type-C charging cable into the computer or USB port.
During charging: the red light is al ways on.
Charging completed: the red light goes out automatically.

HOW TO CALIBRATE?

NOTE

1. If the stabilizer cannot be worked normally, it is usually caused by low battery. Please fully charge before using it.
   (For transportation safety, the item’s electricity is usually controlled at about 50% during production. In addition, the long transportation time leads to partial loss of electricity on the way, resulting in low electricity when the  product is received)

2. Under normal condition, please do not use the calibration function. (Once the calibration method is incorrect, it may cause the stabilizer can not work properly)

3. If the stabilizer still can not work properly, please try below calibrate steps.

1. Open the tripod;
2. Fix the stabilizer with both hands to keep balance (Operate as shown in Figure 1 for horizontal unbalance, and as shown in Figure 2 for vertical unbalance);
3. Click the power key of the stabilizer 4 times in a row;
4. The stabilizer vibrates continuously and the calibration is completed.

WARM TIPS

1. When the device is held on the stabilizer holder, please try to keep it in the center. If it cannot be centered, please adjust the phone holder to the horizontal direction to use.
2. If there is no operation within 10 minutes of Bluetooth connection, the selfie stick will automatically enter the dormant state. And it will automatically shut down after 30 minutes of dormancy.
3. When the battery of remote control/stabilizer is low, the red light will flash. Please charge in time.
4. After the remote control is turned on, it will automatically connect to the old device. When the remote control is connected to a new device, please make sure the Bluetooth of old device has been turned off or is 10 me ters/35 feet away from the remote control.

THANKS!
Version 2.0
MADE IN CHINA

Documents / Resources

| Qimic WS-21006 Gimbal Stabilizer for Smartphones Selfie Stick Phone Tripod [pdf] Instruction Manual
WS-21006 Gimbal Stabilizer for Smartphones Selfie Stick Phone Tripod, WS-21006, Gimbal Stabilizer for Smartphones Selfie Stick Phone Tripod, Smartphones Selfie Stick Phone Tripod, Selfie Stick Phone Tripod, Stick Phone Tripod, Phone Tripod, Tripod
---|---

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>