CHRONOS 30R-001 Commercial 10 Qt. Standard Duty Planetary Mixer Owner’s Manual

PLANETARY MIXER MANUAL
30R-001/ 30R-002/ 30R-003/ 30R-004

Thank you for choosing to purchase from Chronos. Every Chronos product is manufactured with the customer in mind, providing the best value without sacrificing quality. Chronos planetary mixers are ETL and NSF certified, meeting key standards for health and safety in commercial food service establishments.

Receiving & Inspecting

EQUIPMENT
Care must be taken during unloading so the equipment is not damaged while being moved into the building.

1. Visually inspect the exterior of the package. Note any damage and report it to the delivering carrier immediately.
2. If damaged, open and inspect the contents with the carrier.
3. In the event that there is concealed damage upon opening, notify the carrier. Notification should be made verbally as well as in written form.
4. Request an inspection by the shipping company of the damaged equipment. This should be done within 10 days from receipt of the equipment.
5. Freight carriers can supply the necessary damage forms upon request.
6. Retain all crating material until an inspection has been made or waived.

Package Contents

The following is included:

• Food Mixer
• Spiral Dough Hook
• Whisk
• Mixing Bowl
• Beater
• Instruction Manual

Technical Parameters:

Model #| Volt| Watts| Weight| 1st Speed
RPM| 2nd Speed
RPM| 3rd Speed
RPM| Width
(in)| Depth
(in)| Height
(in)
---|---|---|---|---|---|---|---|---|---
30R-001| 120| 550| 99 lbs.| 108| 195| 355| 15.5| 15.5| 24
30R-002| 120| 1100| 238 lbs.| 108| 195| 355| 21.85| 22| 31.3
30R-003| 120| 1500| 396 lbs.| 91| 166| 282| 23.5| 24| 45
30R-004| 240| 2200| 418 lbs.| 91| 166| 282| 23| 24| 45

Main External Parts

1. Gear change hand lever
2. Stirring shaft
3. Mixer
4. Stainless barrel
5. Power switch
6. Bent lever
7. Safety guard (may choose the fitting)
8. Support

Operation INSTRUCTIONS

1. Ensure proper power supply by checking the Mixer’s control panel. Consult with the Electrician before installing.
2. Select your mixer attachment (3) and attach it to the mixer shaft (2) by rotating it clockwise until the pin locks the attachment into the mixer shaft (2).
3. Add ingredients to mixer bowl. It is best to start with a small number of ingredients and add the desired amount as mixing progress. This will prevent overworking the motor and overflow of product.
4. Using the bowl lift lever (6), raise the bowl up to the highest position. Starting procedures: Pull the gear change hand lever (1) to position 1 before starting, then turn on the power switch 5 and set the speed required. After the mixer is in normal operation, pull the hand lever (6) to the highest point and lift the support (7) to the highest point.
5. Never change speeds during operation. First, turn off the power switch (5). Once the mixer comes to a complete stop, select your speed using the hand lever (1) before restarting the mixer.
6. When the operation is finished, turn off the power switch (5). Pull the hand lever (1) to the 1st speed. Return the bowl to the bottom position using the bowl lever (6). Disconnect the power supply.

Accessories AND FUNCTIONS

1. Whisk: Used for stirring liquid material such as whipped cream and egg. Recommended speed: mid or high speed.
2. Beater: Used for stirring creams, powders pastes, and other ingredients such as cake batter. Recommended speed: start with low speed, end with mid speed.
3. Spiral dough hook: Used for stirring sticky material, such as dough. Recommended speed: low speed.

Notes

1. The power socket must be provided with a good ground wire to guarantee the mixer’s good grounding through it. There will be an electric shock if no ground wire or improper grounding is mounted. The ground wire can never be connected with a gas pipe, water pipe, lightning rod, or telephone line. Electric leakage should be checked after installation. Once the power line becomes damaged, the user must replace them with a special maintenance service company.
2. Don’t put your hands into the stirring barrel during operation. The power supply should be disconnected before the mixers are going to be installed.
3. Don’t operate the mixer beyond the time limit to prevent a reduction in its service life.
4. The mixer should be mounted in a stable and clean place. Keep it away from overheated or overwet places and away from equipment that has strong electromagnets or can produce strong electromagnets.
5. Keep the machine clean at all times. Always disconnect the power supply before any cleaning or maintenance. Clean the mixer with a soft, damp cloth. Do not use abrasive
   cleaners or detergents.

Maintenance AND TROUBLESHOOTING

Maintenance
Clean the bowl and stirrer daily or after use to maintain hygiene standards.
The transmission gearbox is greased in the factory. Check the greasing every 6 months. To assess or refill grease, open the top cover, then fill grease from the aperture or replace the grease directly.
Trouble Shooting

the power supply
Overloaded| Reduce load
The speed of mixing is too high
or using a wrong stirrer| Select a suitable speed and stirrer
The mixing knocks with the bowl| The stirrer bowl is deformed| Repair or replace the stirrer or bowl
Abnormal noise and high temperature from the gearbox| Insufficient lubrication| Add or replace the grease

Warning!
If the equipment is out of function, please make sure that it is serviced by a professional person, or please turn to a special service point.
The mixer will NOT START unless:
Bowl is secure in the up position
Unit plugged in
Timer is enabled
The safety guard is closed

PARTS & DIAGRAMS

Parts of 10L

SER.NO.| PART.NO.| PART NAME| SER.NO.| PART.NO.| PART NAME
---|---|---|---|---|---
1| 10-1| Flat Beater| 69| 10-69| Shifting yoke
2| 10-2| Hook| 70| 10-70| Inner gear
3| 10-3| Wire whip| 71| 10-71| hexagon socket cap screws
4| 10-4| Gearbox| 72| 10-72| Circlips for shaft
5| 10-5| Circlips for shaft| 73| 10-73| Planet gear
6| 10-6| Worm pole| 74| 10-74| Operatingshelf
7| 10-7| Oil seal| 75| 30-76| Bearing
8| 10-8| Key| 76| 10-76| Running shaft support
9| 10-9| Motor| 77| 30-76| Bearing
10| 10-10| fan| 78| 10-78| Oil seal
11| 10-11| Back cover| 79| 10-79| Key: 5X20
12| 10-12| Nut: M5X60| 80| 10-80| running spindle
13| 10-13| Spring washer| 81| 10-81| Retainer-spring
14| 10-14| Connector| 82| 10-82| Bowl
15| 10-15| Nut: M4X8| 83| 10-83| cross recess ahead screw
16| 10-16| Red button| 84| 10-84| Moving frame clamp
17| 10-17| Green button| 85| 10-85| front shield
18| 10-18| Nut: M4X8| 86| 10-86| back shield
19| 10-19| Brand| 87| 10-87| hexagonal head bolt
20| 10-20| Nut: M4X20| 88| 10-88| Bumppinblock
21| 10-21| The micro switch installation| 89| 10-89| cross recessed countersunk head screw
22| 10-22| Distance switch| 90| 10-90| Allen flat end set screws
23| 10-23| Nob| 91| 10-91| steel ball
24| 10-24| Speed handle| 92| 10-92| Taper pin column
25| 10-25| Nut: M4X8| 93| 10-93| Support
26| 10-26| fix seat| 94| 10-94| Spring washer
27| 10-27| Spring| 95| 10-95| Type 1 hexagonal nut
28| 10-28| steel ball| 96| 10-96| cross recessed countersunk head screw
29| 10-29| Retainer-spring| 97| 10-97| Support lifting climbing
30| 10-30| nob| 98| 10-98| hexagon lock nut
31| 10-31| deep groove ball bearing| 99| 10-99| flat washer
32| 10-32| Plug| 100| 10-100| compression spring
33| 10-33| Spring| 101| 10-101| flat washer
34| 10-34| Roller: 6X10| 102| 10-102| elastic cylindrical pin

Parts of 10L

SER.NO.| PART.NO.| PART NAME| SER.NO.| PART.NO.| PART NAME
---|---|---|---|---|---
35| 10-35| Gear| 103| 10-103| Connecting rod
36| 10-36| Super machine parts| 104| 10-104| cotter
37| 10-37| ring gasket| 105| 10-105| Retainer-spring
38| 10-38| Combination of gear| 106| 10-106| Crank lever
39| 10-39| Gear shaft sleeve| 107| 10-107| Handle
40| 10-40| Claw-type clutch| 108| 10-108| Stud
41| 10-41| Key: 5X25| 109| 10-109| hexagonal head bolt
42| 10-42| Key: 5X30| 110| 10-110| foundation
43| 10-43| Key: 5X30| 111| 10-111| hexagonal head bolt
44| 10-44| Main shaft| 112| 10-112| Power cord
45| 10-45| Gear shaft sleeve| 113| 10-113| The power supply is waterproof connectors
46| 10-46| Gear| 114| 10-114| cross recess pan head screw
47| 10-47| Spring washer| 115| 10-115| Contact switch
48| 30-36| Bearing| 116| 10-116| Type 1 hexagonal nut
49| 10-49| Oil seal| 117| 10-117| Ac contactor stents
50| 10-50| Bearing| 118| 10-118| shied
51| 10-51| Gear shaft| 119| 10-119| cross recess pan head screw
52| 10-52| Key: 5X10| 120| 10-120| cross recess pan head screw
53| 10-53| Key: 5X10| 121| 10-121| Capacitor
54| 10-54| Combination of gear| 122| 10-122| Capacitor
55| 10-55| Circlips for shaft: 55| 123| 10-123| cross recess pan head screw
56| 10-56| Gear| 124| 10-124| Travel switch fixed plate
57| 10-57| Circlips for shaft| 125| 10-125| cross recess pan head screw
58| 10-58| Bearing| 126| 10-126| Type 1 hexagonal nut
59| 10-59| Bearing| 127| 10-127| Travel switch bracket
60| 10-60| Key: 5X14| 128| 10-128| Distance switch
61| 10-61| Shaftwormgear| 129| 10-129| cross recess pan head screw
62| 10-62| Worm gear| 130| 10-130| Type 1 hexagonal nut
63| 10-63| Circlips for shaft| 131| 10-131| Shield compression spring
64| 10-64| Bearing| 132| 10-132| Switch shaft pin
65| 30-7| Control nut| 133| 10-133| split washer
66| 10-66| Spring| 134| 10-134| Switch shaft pin compression spring
67| 10-67| Fork pin| 135| 10-135- Version 4| overload switch
68| 10-68| declutch shift shaft

Parts of 20L

SER.NO.| PART.NO.| PARTNAME| SER.NO.| PART.NO.| PARTNAME
---|---|---|---|---|---
1| 20-1| Vire whip| 44| 20-44| Rine
2| 20-2| Spiral dada hook| 45| 30-26| Bearing
3| 20-3| Flat Beater| 46| 20-46| Bushier
4| 20-4| Safety guard| 47| 20-47| Oil seal
5| 20-5| Bowl ar. early| 48| 20-48| Fore luny
6| 30-7| Plunger-After yoke| 49| 20-49| Support
7| 30-8| Swine| 50| 20-50| Cage
8| 30-9| Pin shaft| 51| 20-51| No
9| 20-9| Shiftier yoke| 52| 20-52| Beerier
10| 30-11| Cam-gear shifter| 53| 20-53| Mid-rear wheel
11| 30-12| Plate-sbillerinder| 54| 20-54| Rey
12| 20-12| Frandle-shillercover| 55| 20-55| Circlips for .haft
13| 20-13| Renelle-shifter| 56| 20-56| Gear
14| 20-14| Speed handle| 57| 20-57| Buskin.
15| 20-15| Gear came eland| 58| 20-58| Gear
16| 20-16| Nat| 59| 20-59| Plus cover
17| 20-17| Pre..ier plate| 60| 20-60| Wore wheal
18| 30-35| Plus cover| 61| 20-61| Oil seal
19| 20-19| Super machine parts| 62| 30-84| Green butt=
20| 20-20| Declutch shift shaft| 63| 20-63| Red button
21| 20-21| Eve| 69| 20-64| Brand
22| 20-22| Nat| 65| 20-65| Motor box
23| 20-23| Stain .haft| 66| 20-66| K..9
24| 20-24| Gearbox| 67| 20-67| Shaft woo gear
25| 20-25| End can| 68| 20-68| Gear
26| 20-26| InternsIgesr| 69| 20-69| 110V/5082 Motor(with tool)
27| 20-27| Gear| 70| 20-70| Back Housing
28| 20-28| Opersiingsbalf| 71| 20-71| Back Cover
29| 30-36| Beerier| 72| 20-72| needle-shifter
30| 20-30| Oil .eal| 73| 20-73| Crank lever
31| 20-31| Forking shaft| 74| 20-74| Connecting rod
32| 20-32| Ftetsiner-pin| 75| 20-75| Stud
33| 20-33| Senior| 76| 20-76| Clam plate
34| 20-34| Pres.in plate| 77| 20-77| Clasp plate
35| 20-35| Tranmai..ion .haft support| 78| 20-78| Sprier
36| 30-53| Bearing| 79| 30-92| Distance switch
37| 20-37| Spacer-lower| 80| 20-80| Overload ‘witch
38| 20-38| Circlips for bolt| 81| 20-81| Power cord
39| 20-39| Rine casket| 82| 20-82| The power supply is waterproof connectors
40| 20-40| Gear
41| 30-40| Bushing| 83| 20-83| Contact ‘witch
42| 20-42| Sleeve| 84| 20-84| Capacitor
43| 20-43| Claw type rear wheel| 85| 20-85| Capacitor

Parts of 20L with Hub

SER.NO.| PART.NO.| PART NAME| SER.NO.| PART.NO.| PART NAME
---|---|---|---|---|---
1| 20-1| Wire whip| 46| 20-46| Burling
2| 20-2| Spiral dough hook| 47| 20-47| Oil seal
3| 20-3| Plat Beater| 48| 20-48| For lump
4| 20-4| Safety guard| 49| 20-49| &SIM
5| 20-5| Bowl assembly| 50| 20-50| Care
6| 30-7| Plunger-shifter yoke| 51| 20-51| Nut
7| 30-8| Spring| 52| 20-52| Bearing
8| 30-9| Piashaft| 53| 20-53| Mid-gear wheel
9| 20-9| Shifting yoke| 54| 20-54| Rey
10| 30-11| Csm-parshitler| 55| 20-55| Circling for shaft
11| 30-12| Olseshifterincks| 56| 20-56| Gear
12| 20-12| Handle-shifter cover| 57| 20-57| Barbing
13| 20-13| Handle-shifter| 58| 20-58| Gear
14| 20-14| Speed handle| 59| 20-59| Plus cover
15| 20-15| Gear cage gland| 60| 20-60| Worm wheel
16| 20-16| Nut| 61| 20-61| Oil real
17| 20-17| Pressing plate| 62| 30-84| Green button
18| 30-35| Plug cover| 63| 20-63| Red button
19| 20-19| Super machine parts| 64| 20-64| Brand
20| 20-20| Declutch shift shaft| 65| 20-65| Motor box
21| 20-21| Ring| 66| 20-66| Key
22| 20-22| Nut| 67| 20-67| Shaft worm gear
23| 20-23| Main shaft| 6S| 20-68| Gear
24| 20-24| Gearbox| 69| 20-69| 110V/50112 Motor(with tool)
25| 20-25| Plug attachment hub| 70| 20-70| Back Housing
26| 20-26| Internal gear| 71| 20-71| Back Cover
27| 20-27| Gear| 72| 20-72| Handle-shifter
28| 20-28| Operatiorshalf| 73| 20-73| Crank lever
29| 30-36| Bearing| 74| 20-74| Connecting rod
30| 20-30| Oil real| 75| 20-75| Stud
31| 20-31| Working shaft| 76| 20-76| Claw plate
32| 20-32| Retainer-pin| 77| 20-77| Clamp plate
33| 20-33| Spring| 78| 20-78| Spring
34| 20-34| Pressing plate| 79| 30-92| Distance witch
35| 20-35| Transmission shaft support| 80| 20-80| Overload =witch
36| 30-53| Bearing| 81| 20-81| Power cord
37| 20-37| Spaces—lower| 82| 20-82| The power supply is waterproof connectors
38| 20-38| Circling for shaft
39| 20-39| Ring gasket| 83| 20-83| Contact =witch
40| 20-40| Gear| 84| 20-84| Capacitor
41| 30-40| Bushing| 85| 20-85| Capacitor
42| 20-42| Sleeve| 86| 20-86| Attachment hub
43| 20-43| Claw-type gear wheel| 87| 20-87| Spring
44| 20-44| Ring| 88| 20-88| Circling
45| 30-26| Bearing| 89| 20-89| Gear

Parts of 30L

SER.NO.| PART.NO.| PART NAME| SER.NO.| PART.NO.| PART NAME
---|---|---|---|---|---
1| 30-1| Hook| 49| 30-49| Support
2| 50-2| Eeater| 50| 30-50| Clasp plate
3| 50-3| Wire Whip| 51| 30-51| Nut
4| 30-4-session 4| Safety guard| 52| 30-52| Base
5| 30-5| Bowl| 53| 30-53| Bearing
6| 50-6| Top cover| 54| 30-54| Tran.17410. shaft =peon
7| 50-7| Screw| 55| 30-55| Hey
8| 50-8| Spring| 56| 30-56| circle for 111.11
9| 50-9| Pin shaft| 57| 30-57| Gear
10| 30-10| Shifting yoke| 58| 30-58| 5unang
11| 30-11| Can-Rear salter| 59| 30-59| Trent nouslos
12| 30-12| Plate-Anftes laden| 60| 30-60| Worn ancel
13| 30-13| Randle-3131fter| 61| 30-61| UMW
14| 30-14| Randle set| 62| 30-62| Gaze
15| 30-15| Turnout| 63| 30-63| Back cover
16| 30-16| Speed Mane| 64| 30-64| Internal gees
17| 30-17-version 4| Plus attachment S.| 65| 30-66-version 1| =15. able
18| 30-18-version 4| overload solution.| 66| 30-66| Seal up r1116
19| 30-19-version 1| Power cord| 67| 30-67| Gear Waft
20| 30-20-version 4| Power supply is waterproof connectors| 68| 30-68| Gear
21| 30-21-version 4| Contact rant.| 69| 30-69| Busting
22| 30-22| Hood ring| 70| 30-70| Gear
23| 30-23| Orals. for Van| 71| 30-71| Gear
24| 30-24| Planet gear| 72| 30-72| Plate
25| 30-25| GPeraling a self| 73| 30-73| Plug 1
26| 30-26| Bearing| 74| 30-14| Nut
27| 30-27| 011 seal| 75| 30-16| Spring plate
28| 30-28| Fin| 76| 30-76| bearing
29| 30-29| Working Shaft| 77| 30-77| shaft vane Gear
31| 30-30| Declutch| 78| 30-78| Hey
32| 30-31| Plate| 79| 30-79| Ciclled for shaft
33| 30-32| Rain staff| 80| so-so| Circlled for shaft
34| 30-33| Ian| 81| 30-31| Plus 2
35| 30-34| Top natter valve cep| 82| 30-82| 110V/60HZ Motor(with tool)
36| 30-35| Plat valve cap
37| 30-36| Bearing| 83| 30-83-version 4| stop block
38| 30-37| Spacerlorer| 84| 30-84| Green Paten
38-1| 30-38| Super road. rarer.| 85| 30-85| Red Outten
38-1| 30-38-1| Super read= parts| 86| 30-86| Crank lever
38-2| 30-38-1| Gear| 87| 30-87| Sandie-0liter
38-3| 30-38-5| Roller| 88| 50-88| sampling rod
38-4| 30-38-4| 60.111G| 89| 30-89| 50-1113
39| 30-39| Gear| 90| 30-90| Wing plate
40| 30-40| Busking| 91| 30-91| elms plate
41| 30-41| Sleeve| 92| 30-32| Instance soli.
42| 30-42| Gear| 93| 93-version 4| Capacitor
43| 30-43| Clasp plate| 94| 44-version 4| Capacitor
44| 30-44| Bearing| 95| 96-version 4| Switch mounting collar
45| 30-45| Celan=| 96| 96-version 4| Switch Compression spring
46| 10-46| 011 seal| 97| 97-version 4| sp11t washer*.
47| 30-47| 5047 ban,| 98| 98-version 4| The left guard
48| 30-48| Bowl Isola IlltS| 99| 93-version 4| The right paned

Parts of 30L with Hub

ISER.NO.| PART.NO.| PART NAME ISER.NO.| | PART.NO.| PART NAME
---|---|---|---|---|---
1| 10-1| Flat Beater| 69| 10-69| Shifting yoke
2| 10-2| Hook| 70| 10-70| Inner gear
3| 10-3| Wire whip| 71| 10-71| hexagon socket cap screws
4| 10-4| Gearbox| 72| 10-72| Circlips for shaft
5| 10-5| Circlips for shaft| 73| 10-73| Planet gear
6| 10-6| Worm pole| 74| 10-74| Operatingshelf
7| 10-7| Oil seal| 75| 30-76| Bearing
8| 10-8| Key| 76| 10-76| Running shaft support
9| 10-9| Motor| 77| 30-76| Bearing
10| 10-10| fan| 78| 10-78| Oil seal
11| 10-11| Back cover| 79| 10-79| Key: 5X20
12| 10-12| Nut: M5X60| 80| 10-80| running spindle
13| 10-13| Spring washer| 81| 10-81| Retainer-spring
14| 10-14| Connector| 82| 10-82| Bowl
15| 10-15| Nut: M4X8| 83| 10-83| cross recess ahead screw
16| 10-16| Red button| 84| 10-84| Moving frame clamp
17| 10-17| Green button| 85| 10-85| front shield
18| 10-18| Nut: M4X8| 86| 10-86| back shield
19| 10-19| Brand| 87| 10-87| hexagonal head bolt
20| 10-20| Nut: M4X20| 88| 10-88| Bumppinblock
21| 10-21| The micro switch installation| 89| 10-89| cross recessed countersunk head screw
22| 10-22| Distance switch| 90| 10-90| Allen flat end set screws
23| 10-23| Nob| 91| 10-91| steel ball
24| 10-24| Speed handle| 92| 10-92| Taper pin column
25| 10-25| Nut: M4X8| 93| 10-93| Support
26| 10-26| fix seat| 94| 10-94| Spring washer
27| 10-27| Spring| 95| 10-95| Type 1 hexagonal nut
28| 10-28| steel ball| 96| 10-96| cross recessed countersunk head screw
29| 10-29| Retainer-spring| 97| 10-97| Support lifting climbing
30| 10-30| nob| 98| 10-98| hexagon lock nut
31| 10-31| deep groove ball bearing| 99| 10-99| flat washer
32| 10-32| Plug| 100| 10-100| compression spring
33| 10-33| Spring| 101| 10-101| flat washer
34| 10-34| Roller: 6X10| 102| 10-102| elastic cylindrical pin

5E8.0.| PART.NO.| PART NAME| SOUP.| PART.NO.| PART NAME
---|---|---|---|---|---
1| 30-1| look| 51| 30-51| Nut
2| 30-2| Beater| 52| 30-52| Base
3| 30-3| Wire Whip| 53| 30-53| Beating
4| 30-4| Safety guard| 54| 30-54| Transmission shaft support
5| 30-5| Bowl| 55| 30-55| Key
6| 30-6| Top cover| 56| 30-56| Credits for shaft
7| 30-7| Screw| 57| 30-57| Gear
8| 30-8| Spring| 58| 30-58| Bushing
9| 30-9| Pin shaft| 59| 30-59| Front housing
10| 30-10| Shifting yoke| 60| 3660| Worm wheel
11| 30-11| Cam-gear shifter| 61| 3661| MARK
52| 30-12| Plate-shifter index| 62| 3662| Case
13| 30-13| Handle-shifter| 63| 3063| Back cover
13| 3614| Handle set| 64| 3664| Internal gear
15| 30-15| Turns| 65| 30-65-version 3| switch axle
16| 30-16| Speed handle| 66| 3066| Seal to ring
17| 30-17| Plug attachment hub| 67| 3067| Gear shaft
18| 30-18| Attachment hub| 68| 3668| Gear
19| 30-19| Spring| 69| 3669| Bushing
20| 30-20| Circlips| 70| 30-70| Gear
21| 30-21| Gear| 71| 30-71| Gear
22| 30-22| Hood ring| 72| 30-72| Plate
23| 30-23| Circkps for shaft| 73| 30-73| Plug 1
24| 30-24| Planet gear| 74| 30-74| Nut
25| 30-25| Operating shelf| 75| 30-75| Sitting Plate
26| 30-26| Bearing| 76| 30-76| Bearing
27| 30-27| Oil seal| 77| 30-77| Shaft worm gear
28| 30-28| Pin| 78| 30-78| Key
29| 30-29| Working shaft| 79| 30-79| Credits for shaft
30| 30-30| Dedutch shift shaft| 80| 30-80| Circlips for shaft
31| 30-31| Plate| 81| 30-81| Plug 2
32| 30-32| Mail shaft| 82| 30-82| 110V/50HZ MotOr(Mth tool)
33| 30-33| Not| 83| 30-83-version 3| stop block
34| 30-34| Top batter valve cap| 84| 30-84| Green button
35| 30-35| Flat valve cap| 85| 30-85| Red button
36| 30-36| Bearing| 86| 30-86| Crank lever
37| 30-37| Spacer-lower| 87| 30-87| Handle-shifter
38| 30-38| Super machine parts| 88| 30-88| Connecting rod
38-1| 30-38-1| Super machine parts| 89| 30-89| Spring
38-2| 30-38-2| Gear| 90| 30-90| Spring Plate
38-3| 30-38-3| Roller| 91| 30-91| Clamp plate
38-4| 30-38-4| Spring| 92| 30-92| Distance switch
39| 30-39| Gear| 93| 93| overload switch
40| 30-40| Oohing| 93| 94| Power cord
41| 30-41| Sleeve| 95| 95| The power supply is waterproof connectors
42| 30-42| Gear| 96| 96| Contact switch
43| 30-43| damp plate| 97| 97| Capacitor
44| 30-44| Bearing| 93| 98| Capacitor
45| 30-45| Bushing| 99| 99-version 3| switch mounting collar
46| 30-46| 03 seal| 100| 100-version 3| Switch compression spring
47| 30-47| Body housing| 101| 101-version 3| split washer
48| 30-48| Bowl hold kits| 102| 102-version 3| The left guard
49| 30-49| Support| 103| 103-version 3| The right guard
50| 30-50| Clamp plate| | |
SER.NO.| PART.NO.| PART NAME| SER.NO.| PART.NO.| PART NAME
---|---|---|---|---|---
105| 40-105| Timer| | |
106| 40-106| Timer knob| | |
107| 40-107| Rubber feet| | |

Proper DISPOSAL

To help prevent possible harm to human health and/or the environment, the product must be disposed of in an approved and environmentally safe recycling process. For further information on how to dispose of this product correctly, contact the product supplier, or the local authority responsible for waste disposal in your area.
Parts have undergone strict product testing in order to comply with regulatory standards and specifications set are international, independent, and federal authorities.
Declaration OF CONFORMITY

• Certificate

**Warranty INFORMATION

**

One-Year Limited Warranty
Chronos offers a 1-year warranty to the original purchaser of new equipment, the model of equipment will be free of defects in material and workmanship for a period of 1 year from the date of delivery. The warranty is not transferrable. Chronos, at its own discretion, will provide replacement components, replace the entire unit or refund the purchase price to satisfy the warranty obligation.
Chronos makes no other warranties, express or implied, statutory or otherwise, and hereby disclaims all implied warranties, including the implied warranties of merchantability and of fitness for a particular purpose.
The year limited warranty does not cover:

• Failure to install and/or use the equipment within proper operating conditions as specified by Chronos.
• Outdoor use will void the warranty. The finish is not guaranteed in mobile applications where the table can be damaged due to not being secured to the floor.
• Products that have been modified, abused or misused. Any products that have been exposed to corrosive or other cleaners not intended for use on stainless steel will void the warranty.
• Any products sold outside the contiguous United States.
• Any products where the original sale cannot be determined. No order #, invoice, or receipt to provide proof of purchase will result in no warranty coverage.
• Labor or service not authorized by Chronos is not covered under this warranty.
• Freight damage must be made at the time of delivery and addressed with the carrier for compensation.
• Chronos will not be liable for any parties that experience loss of product, consequential damage, lost business, or any other expenses.
• Defects or damage due to improper maintenance, wear, and tear, abuse, misuse, vandalism, or Act of God.

For Warranty Inquiries
To obtain warranty information or make a claim against this warranty, please contact the location where you purchased the product. If purchased on www.centralrestaurant.com , call 800-215-9293 or email sales@centralrestaurant.com.

Central Restaurant Products®
7750 Georgetown Road » Indianapolis, IN 46268
800.222.5107
www.centralrestaurant.com
sales@centralrestaurant.com

Documents / Resources

| CHRONOS 30R-001 Commercial 10 Qt. Standard Duty Planetary Mixer [pdf] Owner's Manual
30R-001, 30R-002, 30R-003, 30R-004, Commercial 10 Qt. Standard Duty Planetary Mixer, 30R-001 Commercial 10 Qt. Standard Duty Planetary Mixer
---|---

References

• Central Restaurant Products: Commercial Restaurant Supplies & Equipment Store

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>