Shenzhen Aita Technology AT-BT829 Bluetooth Headset User Manual

Shenzhen Aita Technology AT-BT829 Bluetooth Headset User Manual

Introduction

Thank you for using AITA to provide you with the AT BT829 Bluetooth stereo headset be few you use please read this manual.

Introduction of Bluetooth Technology
Bluetooth is a short-range communications support equipment (usually within 10M) radio technology, in Including the exchange of information between a wireless Bluetooth mobile phones, laptops and other IT digital equipment The use of “Bluetooth” technology can effectively simplify the communication between devices, so that the data transfer becomes more quickly and efficiently. Handout

1. Headphone
2. USB cable
3. Manual
4. Computer Cables

Specification

Note: Due to the different environment of paired devices, headphones working hours will vary

Preview

1. Power on off
2. USB Interface
3. Charging port
4. Next song Pause
5. Line – IN Connector
6. Volume + / –
7. Tuner
8. Card entry

Battery Charging

Headphones with built-in Recharge Battery the battery must be fully charged before first use as ride two charging methods:

Use power bank

1. Plug the charger into a standard AC power outlet

2. Connect one end of the USB cable into the charger and the other end connected to the charger interface headset.
   Red light is charging, the red light goes out indicate charging is complete.

3. Use travel recharge your time: about 2.5 hours

Use computer USB port to charge

1. The USB charging cable into your computer’s USB port

2. Connect the other end of the USB cable to the headset charging port.
   Red light shows that are filled Electricity, the red light goes off indicates charging is complete.

3. USB cord computer charge time: about 2.5 hours

How To Use

Pairing/Power On/Off

Function| Using the Operation| Indicator| A long “beep” sound after
---|---|---|---
Pairing| Press and hold the multifunction button for 5 seconds, see Blue lights flash after release button| Alternately flashing
red and blue lights| Two consecutive short “beep” Indication tone
Open| Press and hold the multifunction button for 3 seconds, see Blue lights flash after release button| Blue lights flash 4 times| A long n beep” sound
Closed| Press and hold the multifunction button for 3 seconds, see Blue lights flash after release button| Blue lights flash 4 times| A long n beep” Sound

Note: Pairing mode for 2 minutes over two minutes with any device pairing, the head set will be cut. Switch to standby mode after 5 minutes if the power is not connected to any device, he headset ill au tom attar shutdown to save pow et

Pairing with mobile phone,
First make sure your phone s Bluetooth feature is available, the process may vary depending on the specific pairing the phone Varies, detailed instructions, please read the phone paired Bluetooth devices guidelines

Pairing the following steps

1. The distance phone and headset kept within one meter
2. Headset into paring mode
3. Open the Bluetooth phone, search for Bluetooth devices.
   When the search is completed, the set displayed Equipment list, select the AT—BT829 According to the tone by phone to confirm, the pairing is successful 5sec After a successful connection, headphone blue lights flash twice every four nods

Note: After pairing is successful, the device will record each interaction, the next use without re—pairing, Bluetooth version Lower than V2.1 phone prompts for cryptographic key or PIN: 0000

Pair and connect the computer

Firstly, please make sure your computer itself have Bluetooth function, if not, you can go to buy a Bluetooth adapter, pairing steps are as follows.

1. Keep the headphones and computer distance within 1 meter
2. Activate the headphones into pairing mode (Check “pairing mode”)
3. Tum on the computer Bluetooth option, click on the “add equipment” dick “next move” select “the AT – Bt829” next move complete
4. When the headset is connected to your device and is ready to use, the blue indicator light flashes twice every four seconds.
   Note: (1) Pairing with Windows VISTA, Windows 7 system for reference, other versions need to in accordance with the system prompts (2) If the computer Bluetooth version is lower than 2.14EDR, need pas-scode”0000″ .
   Note: After mufti device be paired successfully, the paired device will remember each other, unless the pairing information is removed because of t-he new pair, otherwise the next time you use, connect the headset with the phone’s hands-free function. Next, re-open the transmitter, you can create multi-device connection. For the mobile which supportA2dIp & Hsp agreement, and it may be both connected, then re-open the Bluetooth transmitter, the device may not be connected with the headset.

Place the headset on the ear

The headset is fordable, which is adjustable. Marking “L” corresponding to the left ear headphones, marked “R” corresponding to the right, according to the corresponding, Please wear it correctly.
Please touch all keys before starting to activate current.

Playing music

When the headset and computer which support A2dp, Bluetooth molt phone or Bluetooth transmitter is connected, you can enjoy wireless music through head phones.

Note: When the head set volume reach to Maximum or minimum, you will hear a Ding Dong sound hints.

Communication

Note: Some Telephones Do Not Support the function, Please read the instruction manual of your mobile when the headset volume reach to maximum or minimum, you will hear a loud ding dong sound promote.

The meaning of indicator light and prompt sound

Charging

Charging

Working

(not consecutive devices)
Blue light (low battery turns red) flash every 4 seconds 2 seconds| Standby (connected device)
Blue light (low battery turns red) continuous flash (flash three times per second)| Calls in
Blue light (low battery turns red) continuous slowly flash 1 time| On the line

Environment Index

“X” indicates that the substance under the limit required standards for content SJ/J 11363-2006 “0” indicates that the substances in excess of the standard limit requirement SJ/J11 363-2006
The information provided in this form is based on data provided by suppliers of the results of internal tests and “Ai Ta “, Under the current technology, some parts containing hazardous substances control has reached the lowest line. “Ai Ta” will continue efforts to reduce the use of physical force element through technical improvements.
Environmentally friendly use period is 10 years. The use period of exchangeable parts as shown at right battery may be different Only use this product under normal circumstances, environmental protection use period to be effective.

Warranty

AITA product warranty for one year from the purchase, the warranty conditions and obligations are as follows:

1. Warranty required to produce proof of purchase, in case of the ab since of any evidence of warranty Time calculated from the date of manufacture in accordance with the product.
2. If the product before the repair had an unauthorized third party ma tenancy, disassemble situation Conditions no warranty.
3. belongs to the appearance of normal wear and tear parts, batterie s and other accessors are noncovered under the warranty.
4. products for any loss or damage caused in the logistics process, them selves.
5. Warranty need to sent the product was purchased or official auto reed service facility for warranty Repair, love tower on product liability is limited to the discretion repair or reptile the product P base read the warranty

Help extend the life of the product

1. Keep the product dry, do not place the product in damp places, so as not to affect product performance
2. Do not put the product under the sun or high temperatures, high to m prelatures shorten the Becton com ponentes Of life, damage batteries, and some plastic parts deformation.
3. Do not place the product in cold places, so as to avoid damage to the internal circuit boards.
4. Do not attempt to disassemble the product, especially non profess balls, the product may be damaged
5. Do not drop, strong vibration, collision with a hardware product, so as to avoid dam age b the eternal circuity.
6. Do not use sharp objects on the surface of the product random draw, so as not to dam age the appearance.
7. Do not continue to charge the headset over 10 hours, so as not to affect the service life.
8. Do not use other chargers, the use of other chargers could be dangerous and w ill Automatically terminate warranty services.

FCC Caution:
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions: (1) This device may not cause harmful interference, and (2)this device must accept any interference received, including interference that may cause undesired operation.

Any Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.
These limits are designed to provide reasonable protection against harmful interference in a residential installation.
This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications.
However, there is no guarantee that interference will not occur in a particular installation.
If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.
  The device has been evaluated to meet general RF exposure requirement.
  The device can be used in portable exposure condition without restriction.

FAQ

Red light?

The headset battery is running low, you need to charge the headset

Charging, the red light does not flash ?

Make sure the charging device and the headset is connected well If after a long time without using headphones, connect the charger f-or about 30 minutes, the red light will light

Operable from the headset is paired devices and how many meters?

According to the Bluetooth standard, the maximum containable from Class2 type earphone is 10m, but There will be differences in different environments and multi body paired devices

Operable from the headset is paired devices and how many meters?

According to the Bluetooth standard, the maximum containable from Class2 type earphone is 10m, but There will be differences in different environments and multi body paired devices

Why can not find my cell phone headset?

If the headset or the phone is not in pairing mode, the phone can of find the head sets please Ensure that the headset is in pairing mode and qualifying work effectively within the scope of the headset. Before can be paired connection

Headphones can not hear the sound?

Make sure that the headset is in working condition Make sure the headphone volume is appropriate, according to the volume+ Make sure the headset is property paired and connected mobile phone Make sure to work within the scope of headphones

Headsets ineffective ?

Confirm the phone’s signal strength area Whether the headset can be controlled within the range

Why play music, headphones can be remotely controlled?

Please confirm the adequacy of electricity

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>