BEQOOL 192 Wireless HDMI Transmitter and Receiver User Manual

BEQOOL 192 Wireless HDMI Transmitter and Receiver

Connection Diagram

Receiver -RX

Transmitter -TX

Hardware Casting

Combination of receiver and transmitter, plug and play

1. Connect the HD port or VGA port of the receiver to the video input port of the display device such as the monitor or TV.
2. Connect the USB-C power supply port of the receiver to the charging cable and plug it into the power adapter ( Voltage above 51/, current above 2A). Tum on the Receiver power switx:h.
3. Adjust the HD Signal source Df the monitor or TV to the corresponding HD port untithe boot screen is displayed.
4. Connect the transmitter to the computer or other devices With HD video output function . After the indicator Light enters the fast flash state , Wait for ten seconds to complete Casting.

*Please make sure that the power of the computer is suficient. If the power supply of the computer is insuficient or HD is unable to supply power, please connect the transmitter to the power adapter or USB-C power supply port ( Voltage above SV , current above 2A I

Pairing Instructions

The product has been paired out of the factory. In case of pairing failure due to improper operation or other circumstances during use, it is necessary to restore and re pair the device as follows:

1. Please Press the receiver fundion b..itton for more than 3 seconds, and the prompt will pop up on the interface : Release the button to pair With Ezcast TX. Wait for the transmitter to enter pairing mode
2. Press and hold the transmitter function key until the indicator is off and then release the function key until the indicator is on, indicating that the
   connection is successful. (Ensure stable power supply of transmitter during pairing)  With, one receiver and multiple transmitters, 1 receiver can pair with transmitters for switching.

Function Settings

1. Open the phone settings and search for receiver hotspots in the wireless network (Name is RX-,,.., default password is 12345678)
2. Open the mobile enter 192.168.203.1 in the address bar
3. After entering the website, you can operate the distribution network, resolution,upgrade and restart

Problem solving

• How to restore factory settings.
  When the product fails, press and hold the receiver function button for 10 seconds. After a black screen appears and restart the factory settings will be restored.

• Can devices without HD interface be used?
  Yes, please use the device with an HD interlace converter.

• How to enter privacy mode?
  Tap the transmitter function button to disconnect or reconnect.

FCC Warning Statement

Changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular inst allation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment oX a nd on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit diVerent f rom that to which the receiveris connected.
• Consult the dealer or an experienced radio/TV technician for

This device complies with part 15 of the FCC Rules. Operation is help.
subject to the following two conditions: (1) This device may not cause harmful interference, and (2) this device must accept any interference received, including interference that may cause undesired operation.

Specific Absorption Rate (SAR) information:
This smart phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were
developed by independent scientific organizations through period ic and thorough evaluation of scientific studies. The standards include substantial safety margin designed to assure the safety of all persons regardless of age or health.
This cquipment should be installed and operated with minimum distance of 0 cm the radiator your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>