DROCON F19 Drone with Camera for Adults User Manual

DROCON F19 Drone with Camera for Adults

PACKAGE CONTENTS

CHARGING

Low battery warning
When the drone is flying, the indicator lights on the drone are flashing, and the remote control handle emits a “beep” alarm sound, indicating that the drone power is too low. At this time, the drone needs to return and charge.
Charging Guide for battery

1. Connect the USB cable with power supply, the USB LED solid Green, indicate the USB cable is power on.
2. Connect the battery with USB cable. When USB LED solid Red indicate charging status. USB LED solid Green, when charging was completed.

Note:

• The connected USB Adapter should be less than or equal to 5V 2A, the voltage not be greater than 5V, otherwise there is a risk of overloading the USB cable.
• The flight time is approx. 9 minutes (Battery full charge state) and the charging time is about 60 minutes.

INSTALL

1. Open Up all 4 blades for the drone
   This aircraft is folding structure, please do open up all four blades before power on.

2. Blades Protector Installing
   Expand the buckle of the propeller guard, and install it onto the drone wings.

3. Battery Installing

4. Insert the battery into specified position.

5. Keep press the buckle of battery then pull the battery back to take it out.
   Remote Controller:
   Keep pressing the buckle of battery case then pull the case to take it out, insert 3xAAA battery into specified position.

6. Phone clamp installing
   Put the phone clamp to specified position on the remote, and make sure fasten the phone clamp.

REMOTE CONTROLLER

1. Power switch
2. Left joystick (Altitude Control, L/R turning)
3. Right joystick (Movement Control)
4. Left function switch (Take off/Landing, Emergency stop)
5. Right function switch (Headless mode, Return)
6. Take photo
7. Video
8. Speed switch
9. 360° Stunt

HOW TO FLY

1. Switch On the Power

2. First power on the drone (Keep pressing for 2-sec and place it on a flat ground or surface.)

3. Power on the Remote

4. Pairing
   After Powered On the drone, both indicator lights on the Orono and Remote are flashing, then push the Left Joystick to the top, and then down to the lowest (Pie 1 ). After 2 secs, the indicator lights are turning solid, that means the pairing succeed.

5. Gyroscope Calibration
   Push Left Joystick to right corner and Right Joystick to left corner at the meantime (Pie 2).
   The indicator lights of the drone are flashing rapidly for about 3 seconds. The indicator are turning solid when completed.

6. Activate motors for taking-off
   After pairing, push the Left Joystick to the top then release to activate motors, then the propellers start rotating.

7. Take off/ Landing
   

8. Take off : After activated motors, press “Left function switch” (or push up the Left Joystick slowly) to take off.

9. Landing: When the drone in the air, press “Left function switch” (or keep pushing down the Left Joystick slowly) to land.

Emergency Stop

• In case of emergency status, keep press “Left function switch” about 3 seconds, the drone will immediately stop functions and drop off.

USING THE REMOTE CONTROLLER

• Left Stick

• Up/ Down

• Turn left /Turn Right

  • Right Stick

• Forward / Backward

• Left-sideward / Right-

AIRCRAFT FUNCTIONS

Adjustment for deviated flying to Front/Backward

• Vertically press Left Joystick for activate adjustment function.
• If it leans front, push Right Joystick to backward.
• If it leans backward, push Right Joystick to forward.
• Vertically press Left Joystick again for deactivate adjustment function, after finished adjustment.

Adjustment for deviated flying to Sideward

• Vertically press Left Joystick for activate adjustment function.
• If it leans right sideward, push Right Joystick to left side.
• If it leans left sideward, push Right Joystick to right side.
• Vertically press Left Joystick again for deactivate adjustment function, after finished adjustment.
• 360° Stunt Function

1. Press the 360° Stunt
2. Push the stick to right, the drone will rotate 360° toward right direction.

1. Press the 360° Stunt
2. Push the stick to top, the drone will rotate 360° toward front direction.

1. Press the360° Stunt
2. Push the stick to left, the drone will rotate 360° toward left direction.

1. Press the 360° Stunt
2. Push the stick to bottom, the drone will rotate 360° toward back direction.

Note:

• There are continuous beeps from the remote when you activate this function. If you do not move the Right Joystick about 5 seconds after you press the 360° Stunt switch, the function will be cancelled and the remote will stop beeping.
• This function can’t be activated when the battery of the drone is low.

Speed Adjustment

• Press the speed switch to change the speed gear while flying. There are 3 gears, press the Speed switch, you will hear “beep, beep”, means it is on the second gear speed.
• Press again, you will hear “beep, beep, beep” means it is on the third gear speed.
• Press again, you will hear “beep” means it is back to the first gear.
• Remark: Beginners would be suggested to use the first gear speed firstly to play until skillful.

8. RETURN-TO-HOME FUNCTION

• In regular mode, when the drone fly forward, stand and make sure the remote toward the tail of drone then press the “Right function switch” to activate headless mode, no matter which direction that the drone heading to, keep pressing the “Right function switch” about 3 seconds, the drone would fly straight back to remote location.

Note:

1. The drone will not land itself when operate this function, just fly straight toward the remote direction, negative direction operate the right stick to stop flying.
2. If you change your position while playing, Return-to-home function will be inaccurate. Now turn the drone’s tail toward the remote, then press the “Right function switch” to activate headless mode, and keep pressing the “Right function switch” about 3 seconds, then It will come back successfully. Or you can also face to the dome’s tail and calibrate the gyroscope after it lands. Such operation is to update the drone’s return direction.

HEADLESS MODE FUNCTION

• Press the “Right function switch” when the indicator lights slowly flashing, means it is in Headless Mode.
• Press the “Right function switch” again, when the indicator lights stop flashing, means that the Headless Mode is deactivated.
• Users is recommended to stay same orientation as the drone head is facing when the drone takes off.
• Headless Mode, the forward direction is same as the direction when the drone took off, where the head of drone was facing.
• In order to make sure the users can clearly identify drone’s direction, we suggest that users better to stay in the same orientation as the drone facing when it takes off. Then no matter which direction the head is facing, the drone will lock the controlled direction as the remote controller, easy to control back the drone.

PHOTOGRAPH AND VIDEO

Take Photos:
Press the button of “take photo”. Please make sure to open the app on your smart phone before using it, then you can review the photos taken in the media file of app.
Video:
Press the button of “take video”, press to start and press again to finish and save the video. Please make sure to open the app on your smart phone before using it, then you can review the videos taken in the media file of app.

AIRCRAFT PARAMETERS

Remote Controller Parameters

electromagnetic interference)
Working frequency| 2.4G
Battery|  3xAAA

 FAQ

| ISSUES| CAUSE| SUGGESTIONS
---|---|---|---
1| After the battery is insertion the drone, indicator lights on drone keep flashing, no response to operations| Frequency matching between remote and receiver not successful.| Reaerate the frequency matching for remote and drone.
2| No response after battery is inserted in the drone|

1. Check if the power for remote and drone is full charged.
2. Connection of the Power for the Li-Poly battery is not enough.

|

1. 0pen the remote battery case and make sure if the battery is inserted in right position.
2. Use a fully charged battery
3. Reinstall the battery and confirm whether it is good connecting with the poles well.

| |
| |
| |
| | |
| | |
| | |
3| Motor does not run when operating the throttle stick and the indicator lights on drone keep flashing| | Charge the battery or replace it with a full-charged battery
4| Main motor blades spin but the drone won’t fly|

1. Some of the blades have been deformed
2. Battery power is not enough

|

1. Replace the main blade
2. Charge the battery or replace it with a fully charged battery

BATTERY USING ATTENTION

Matters needing attention

1. Rechargeable batteries are to be removed from the toy before being charged.
2. Non-rechargeable batteries are not to be recharged.
3. Rechargeable batteries are only to be charged under adult supervision.
4. Only used to charging 2S Li-ion or Li-polymer battery pack. if not, the charger or battery may be damaged .
5. During charging, the charger should be put in dry and ventilated place and far away from heat source and inflammable and explosive substance.
6. Never immediately charge your battery pack as soon as the flight is finished, or when its temperature doesn’t cool down. Otherwise the battery will take a risk in swelling, even a  fire.
7. Ensure the correctness of polarity before connection the battery to charger.
8. Avoid drop and violence during the process of charging. drop and violence will result in internal short circuit of the battery.
9. For the sake of safety, please use original charging equipment and battery pack. please change new one in time when the flying time is becoming shorten due to long time usage.
10. If it is retained in the charger for a long time after saturated, the battery may automatically discharge. When the charger detects that the voltage of individual cells is lower than the rated voltage, it will re-charge until saturated. Frequently charging and discharging will shorten the lifetime of your battery pack. It is advised that please cut off the power and took off the battery after the charging is saturated.

Maintenance of battery pack

1. The battery pack should be put in dry and ventilated place. The storage temperature of environment is ranged from 18°C to 25°C.
2. Please avoid frequent charging and excessive discharging the battery pack in order to prolong its life cycle.
3. It is a must to maintain the battery pack before long-term storage. That is to charge the battery to the level of 50-60% saturation.
4. If the storage term is over 1 month, it is advised to monthly check the voltage of every cell of the battery pack. The voltage of every cell should be not less than 3V. Otherwise, please refer to the above article ( 3) .
5. From the view point of protection, new battery pack should be motivated before usage. That is to charge and discharge 3-5 times, but discharge is not less than the level of 70%saturation. This process will make the battery lifetime longer and voltage more stable.

SAFETY AND PRECAUSTIONS

• Remote-control models of quadcopter are dangerous merchandise. Their flight must be operated away from the crowd.
• Such factors as man-made improper assembly or mechanical damage, poor control of the electronic equipment. as well as the unfamiliar manipulation may lead to unexpected flight accidents. such as uncontrolled flight and aircraft damage.
• Users are advised to pay attention to the flight safety and understand that they are held responsible for any accident caused by negligence.

• Special drone for Indoor and outdoor should stay away from barriers
• This product is a remote-control drone, that suitable for in indoor using and outdoor environments (the outdoor wind power less than Force 2). To fly this drone, please choose appropriate obstacle-free indoor and outdoor sites with proper distance kept from the crowd or pet animals. Please don’t operate the product in any unsafe environments, such as places of heat, wires, power supply, etc., so as to prevent the quadcopter from the risks of fire and electric shock resulting from collision, ditching, and entangling of the drone.

| |

• Safe usage of the lithium battery
• Lithium batteries are more dangerous than others. Be sure to read carefully and follow the following precautions before using it. We will not be held responsible for any damages caused by any improper use of the battery. To avoid the danger of explosion or fires, it is forbidden to use other chargers than the one made by our factory. Such actions done to the battery as impact, dismantling, reverse connection of the positive and negative poles, and burning are forbidden. Avoid metal objects from contacting the positive and negative poles of the battery, which may cause short circuit. Please prevent sharp items from piercing the battery, and avoid the risk of battery fire. Please be careful when charging the battery Make sure that the battery is charging within your sight. Keep it out of the reach of young children so as to avoid dangers. Don’t charge the battery when the battery is heated after use. Otherwise, it may cause the battery to expand, change, explode or even catch fire, threatening the safety of life and property.
• To dispose of the battery, please recycle the battery in strict compliance with the waste disposal laws and regulations of local countries or regions in order not to pollute the environment

| |

• Away from moist environments
• The interior of the aircraft is also composed of many sophisticated electronic components so it must absolutely be kept away from moisture or water vapor.
• Don’t operate the aircraft in the bathroom or on rainy days; otherwise water vapor may get inside of the aircraft and cause mechanical parts and electronic components to malfunction leading to expected accidents.

| ****

• Never misuse the product
• Please do not disassemble or modify the product. For any upgrade, repair or maintenance, please use the parts specified in our catalog to ensure the safety of the structure. Please make sure the product is used within the limits of operation. Don’t overload the product, and don’t use ii in any other Illegal ways than prescribed by safety concerns and laws.

| ****

• Safe usage of the battery
  

• Batteries are to be inserted with the correct polarity. The supply terminals are not to be short-circuited. Different types of batteries or new and used batteries are not to be mixed. The exhausted batteries are to be removed from the toy.

• For long time storage, please take them out to prevent battery leakage.

• Please dispose abandoned batteries in accordance to the laws and regulations of the corresponding region to prevent pollution to the environment.

|
---|---

• Keep away from source of heat
• The aircraft is mostly made of PA fiber or polyethylene as well as other main materials for electronic products.
• Therefore, it must be kept from the source of heat and exposure to sunlight so as to avoid possible damage of deformation or even meltdown due to high temperatures.

|

• Never operate the product alone
• This product is suitable for users over 14 years old. Since the remote-control quadcopter may pose a certain degree of difficulty for learners at the beginning, it is recommended for it to be operated under the guidance of experienced people for the sake of safe flight.

|

FCC WARNING:

This device complies with part 15 of the FCC rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. This device must accept any interference received, including interference that may cause undesired operation.)

• The manufacturer is not responsible for any radio or tv interference caused by unauthorized modifications or change to this equipment.
  Such modifications or change could void the user’s authority to operate the equipment. This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

RF Warning Statement

• The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction.

DROCON FLY APP

• Download the DROCON FLY App
  The Android version (Play Store) of the DROCON FLY App is compatible with Android 5.0 or later.

• The iOS version (App Store) of the DROCON FLY App is compatible with iOS 8.0 or later.
  In case the App does not display the real-time image, please restart your device and reinstall the App. If the App still does not display the real-time image, check if your device is compatible with the current App version.

• If you have software compatibility issues, please reach us at [email protected]. Specify your device model and OS version, we will try our best to help you.

1. Wi-Fi connection status
2. One-key Return
3. Controller
4. Speed
5. Headless Mode
6. G-Sensor
7. Trajectory
8. Mirroring
9. VR (Split Screen Mode)
10. Home Page
11. Battery Level
12. Takeoff
13. Landing
14. Calibration
15. Stop
16. Take a Photo
17. Record a Video
18. Left-hand control stick
19. Right-hand control stick
20. Trim F/B
21. Trim L/R
22. Speech control
23. Gesture recognition

INTERFACE DESCRIPTION

1. Wi-Fi connection status
   Turn your drone ON and connect your phone to the “Fl9_XXfX’l:I..” Wi-Fi network.

2. One-key Return
   Press “ “to trigger a drone to fly back.

3. Controller
   Press “ “to control the drone with your smartphone. Press it again to change the control back to a remote controller.

4. Speed
   Press “ ” once to set the 1st speed level. Press ” “once again to set the 2nd speed level. Press” ” 3rd time to set the 3rd speed. level.

5. Headless Mode
   Press ” “to turn the headless mode ON.

6. G-Sensor
   Put the drone into the sky and press” “to turn on the G-Sensor mode. When the G-Sensor mode is ON, the drone’s direction is controlled by the G-sensor.

7. Track
   Press “ “to draw a trajectory on the right part of the screen for a drone to follow.

8. Mirroring
   The mirroring function will flip the screen 180 degrees.

9. VR (Split Screen Mode)
   push “ “to split the screen.

10. Home Page
    Push “ “to proceed to the home page.

11. Battery Level
    The battery’s state of charge will be indicated here.

12. Takeoff/Landing
    Push “ “to takeoff.

13. Push ” “to land.

14. Calibration
    Press” “to perform the calibration.

15. Stop
    Press”  “to stop the drone’s motor.

16. Take a Photo
    Press ” ” to take a photo.

17. Record a Video
    Press ” ” to start recording video.

18.  Left-hand control stick / Right-hand control stick

19. Control the drone’s orientation and movement.

20. Trim F/B / Trim L/R

21. Trim the drone by dragging the controller forward / backward / left / right until it stabilizes.

22. Gestures:
    Bi ” ” to take a photo, Bi “5” to video, and then “5” to end the video

23. Voice:
    Take off/landing/forward/backward/left/right

• m.me/DroconOfficials
• 1-855-666-7333
• [email protected]
• www.droconshop.com

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>