Vson Technology WP9510 Label Printer User Guide
- June 4, 2024
- Vson Technology
Table of Contents
Vson Technology WP9510 Label Printer
Product View
How to Use
Power ON/OFF
Long press 2 seconds to Turn ON/OFF
- Indicator light on: Normal running/ Full charged
- Indicator light flash quickly: Error running（Lack of paper，the direction of the paper reversed, Low battery Indicator，Printing head overheating）
- Indicator light flash slowly :Charging
Charge
Please plug the device into the USB cable and connect it to 5V⎓1A adapter or
the computer for charging fully before the first use.
- When the indicator light flashes quickly during charging, check if it means lack of paper. If so, then load the thermal paper, next check if the charging is normal.
*The product is sold without a power adapter.
In the user manual stated if consumers use a power adapter for power supply,
they should buy a matching power adapter that has obtained CCC certification
and meets the standard requirements.
Download “iLabel”APP
User can scan QR code below or search “iLabel” in APP Store/Google Play to
download it.
(Android 6.0 or above and iOS 9.0 or above)
After power on, double click the button to print QR code, scan the QR code to download “iLabel” APP.
Connect to print
- Turn on the phone Bluetooth and the APP, allows applications to gain access (photos, media, files etc) of the phone.
- Then open the APP, connect the device by scan the same QR code printed before.
- Chose [Label printing] and create new label according to the prompts.
Replace the Thermal Paper
- Refer to the picture(1) to push and open the flip cover.
- Refer to the picture(2) to insert the thermal paper, with the thermal paper facing up.
- Refer to the picture(3) to pull out a piece of paper to the outside of the device, and then close the cover. Pay attention to avoid misalignment of the thermal paper.
※ Do not touch the printing head to avoid scalding when changing the printing paper.
Parameters
Product Dimension： 131.086.732.5mm
Print Type： Thermal Printing
Paper Height： 15mm
Printing Height： 12mm
Paper Cutting Method: Manual paper cutting
Capacity： 1000mAh Lithium Battery
Charging Time： About 2~3 Hours
Input： 5V⎓1A
Charging Port： Type-C
Safety Precautions
- This product is with built-in lithium battery, please do not use it higher than 40 ℃, do not close to the fire and other sources of heat, do not placed in the hot sun.
- Do not remove, impinge, puncture or modify the battery. Do not use the battery for other purposes.
- Do not put the product in fire or water to avoid short circuit of the battery causing fire or burns.
- Please do not use this product in high humidity or dusty areas
- Please gently insert or unplug the charging cable to prevent excessive force from damaging the charging interface.
Package
Printer
|
User Manual
---|---
Thermal Paper
|
USB Cable
FCC Statement
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits
for a Class B digital device, pursuant to Part 15 of the FCC Rules. These
limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment generates, uses and
can radiate radio frequency energy and, if not installed and used in
accordance with the instructions, may cause harmful interference to radio
communications.
However, there is no guarantee that interference will not occur in a
particular installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/TV technician for help.
The device has been evaluated to meet general RF exposure requirement. The device can be used in portable exposure condition without restriction
Frequently Asked Questions
Q： No connectable devices were found when adding devices?
A：When adding the device, please check whether the power of the device is enough to work.
Q：The device can not print. How to do?
A：
① Confirm whether the Bluetooth of the mobile phone is on, and exclude the
possibility of others connecting to this device.
② Check whether the thermal paper has been used up, timely replacement of the
thermal paper.
③ Printing head is overheating, if overheating, please let the printing head
cool before trying to print.
④ Restart the device, if still can not solve, please use the pin inserted into
the reset hole for reset.
Q： Why is it all white papers instead of content?
A： It may be caused by the incorrect installation of the thermal paper. Please refer to the introduction of replacing the thermal paper for re-installation.
Q： Why the printed getting lighter?
A：
① Check whether the device is low battery.
② Check whether the printing head and wheel is covered with carbon ink, please
wipe with alcohol softly.