hansgrohe 27268XXX 1 Jet EcoSmart Showerpipe Instruction Manual

June 14, 2024
hansgrohe

27268XXX 1 Jet EcoSmart Showerpipe

hansgrohe

?Safety Notes
? Gloves should be worn during installation to prevent crushing and cutting
injuries.
? The arm of the shower head is intended only to hold the shower head. Do not
load it down with other objects!
? Children as well as adults with physical, mental and/or sensoric impairments
must not use this product without proper supervision. Persons under the
influence of alcohol or drugs are prohibited from using this product.
? Do not allow the streams of the shower touch sensitive body parts (such as your
eyes). An adequate distance must be kept between the shower and you.
? The product may not be used as a holding handle. A separate handle must be
installed.
? The product may only be used for bathing, hygienic and body cleaning
purposes.
? The hot and cold supplies must be of equal pressures.

Installation Instructions

  • Prior to installation, inspect the product for transport damages. After it has been
    installed, no transport or surface damage will be honoured.

  • The pipes and the fixture must be installed, flushed and tested as per the
    applicable standards.

  • The plumbing codes applicable in the respective countries must be observed.

  • The installation dimensions stated in these installation instructions are ideal for
    people of approximately 1800 mm in body height. The dimensions can be
    altered if required. In this case, pay attention to the fact that a change of
    installation height will also change the minimum height, and that the altered
    mounting dimensions must be taken into consideration.

  • During installation of the product by qualified trained personnel, make sure that
    the entire fastening surface is even and smooth (no protruding seams or tile
    offset), that the finish of the wall is suitable to apply the product and has no
    weak points.

  • The mesh washer must be insert to protect the shower against incoming dirt by
    pipework. Incoming dirt leads to defects or/and can damage parts of the
    shower; such caused faults voids all liability and guarantee claims.

  • The product is not designed to be used with steam baths!

  • If required, the bottom part of the pipe between the fixture and the shower head
    can be shortened with a fine-toothed saw.

  • In case of problems with the continuous water heater or of greatly varying
    water pressures, you must install the water limiter (comprised in the delivery,
    article number 97510000) in the cold water supply.

Technical Data

Operating pressure: max. 1 MPa
27268XXX Recommended operating pressure: 0,1 – 0,5 MPa
27281XXX / 26596000 Recommended operating pressure: 0,13 – 0,5 MPa

Test pressure: 1,6 MPa (1 MPa = 10 bar = 147 PSI)

Hot water temperature: max. 60°C
Thermal disinfection: 70°C / 4 min
Centre distance: 150±12 mm
Connections G 1/2: cold right – hot left

• Safety against backflow
• The product is exclusively designed for drinking water!
Symbol description
Do not use silicone containing acetic acid!
Adjustment (see page 34)
To adjust the hot water limiter. Using a hot water limiter in combination with a
continuous flow water heater is not recommended.
Safety Function (see page 41)
The desired maximum temperature for example max. 42º C can be pre-set thanks
to the safety function.
Maintenance (see page 40)
• The check valves must be checked regularly according to EN 806-5 in
accordance with national or regional regulations (at least once a year).
• To guarantee the smooth running of the thermostat, it is necessary from time to
time to turn the thermostat from total hot to total cold.
Dimensions (see page 36)
Flow diagram (see page 36)
 Hand shower
 Overhead shower
Spare parts (see page 41)
Special accessories (order as an extra)
tile-matching-disk #95239000 (see page 41)
Cleaning (see page 38)
Operation (see page 35)
To empty the overhead shower after use, hold it in a slightly inclined position.
Test certificate (see page 41)

Fault Cause Remedy
Insufficient water – Supply pressure inadequate

– Regulator filter dirty
– Shower filter seal dirty|

– Check water pressure (If a pump has been installed
check to see if the pump is working).
-Clean filter in front of the mixer and on the MTC-thermo
cartridge #96922000
– Clean filter seal between shower and hose

Crossflow, hot water being forced into cold water
pipe, or vice versa, when mixer is closed| – Backflow preventers dirty or leaking|

– Clean backflow preventers, exchange if necessary

Spout temperature does not correspond with
temperature set| – Thermostat has not been adjusted
– Hot water temperature too low|

– Adjust thermostat
– Increase hot water temperature to 42 ºC to 60 ºC

Temperature regulation not possible| – thermo cartridge calcified|

– Exchange thermo cartridge

Instantaneous heater didn’t work with thermostat| – Filters are dirty
– check valve hasn’t moved back
– Flow limiter in handshower isn’t removed|

– Clean the filter / exchange filter
– Exchange check valves
– Remove flow limiter

gates

Crometta S 240 1jet Showerpipe EcoSmart
27268XXX

Crometta S 240 1jet Showerpipe EcoSmart

27268XXX

Crometta E 240 1jet Showerpipe EcoSmart

27281XXX / 26596000

Crometta E 240 1jet Showerpipe EcoSmart

27281XXX / 26596000

apps

Cleaning recommendation / Warranty / Contact

Just clean: simply rub over the spray nozzles to remove lime scale.

joint pipes

clock

rop

Overflade

setup parts

Hansgrohe

Hansgrohe · Auestraße 5 – 9 · D-77761 Schiltach · Telefon +49 (0) 78 36/51-1282 · Telefax +49 (0) 7836/511440
E-Mail: info@hansgrohe.com · Internet: www.hansgrohe.com

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

hansgrohe User Manuals

Related Manuals