L-Link AC1200 Dual Band Wireless Repeater Signal Amplifier Instruction Manual

L-Link AC1200 Dual Band Wireless Repeater Signal Amplifier Instruction Manual

Product Parameters

Omnidirectional
Installation| Direct plug-in| Product Color| White
WIFI Frequency| 2.4GHz&5.8Ghz| Power Supply| AC 110〜240V
Working Temperature| 0℃-40℃| Working Humidity| 10%～90%non-condensation
Indicator light and interface description
LED| Power LED| The blue light is always on, indicating

The blue light flashes to indicate thatthe device is starting.
The blue light is off, indicating that thedevice is not powered on.
WPS indicator light| A blue light flashes, indicating WPSnegotiation is in progress.
The blue light is off, it means WPS isnot triggered
Signal indicator light （SYS）| A blue light indicates a strong signal
A green light indicates moderate signal
The red light means the signal is weak
Light off, identification not relayed or relayed unsuccessful
WPS Button| Press short for 1 second to trigger WPS
Reset Button| Long press for more than 6 seconds to restore the equipment to factory state.

Quick Configuration Instructions

Starting device

Insert the repeater into a power outlet near the router and adjust the antenna to the right direction(generally upright and perpendicular to the ground). When the power indicator flashes from the blue light to the normal blue light, the start-up is complete

Wireless extensions-Repeater Mode

Turn on your phone’s or computer’s WIFI and search for the connection repeater SSID(“WLAN-Repeapter-2.4G/WLAN-Repeater-5G), The default is no password. After successful connection, open the browser and enter “192.168.10.1” in the browser to enter the management WEB for quick configuration.

Step1: Set administrative password.

Step2: Scan and select the router’s WIFI signal that needs to be extended.

Step3: Enter the router WIFI password/set the expanded wireless name

1. Router WIFI password
2. Expanded 2.4Ghz Wireless name
3. Expanded 5.8Ghz wireless name

Note: The expanded wireless password is the same as the original router password. If you want to use seamless roaming, please set the expanded SSID to be the same as the main route.

Step4: Confirm extended information.

Step5: Observe the STATE of the LED, complete the configuration, and connect theSSID of the repeater again.

Cable extension—AP Mode

Turn on your phone’s or computer’s WIFI and search for the connection repeater SSID(“WLAN-Repeapter-2.4G/WLAN-Repeater-5G”), The default is no password. After successful connection, open the browser and enter “192.168.10.1” in the browser to enter the management WEB for quick configuration. Step1:Set administrative password

Step2: Select AP Mode and set the wireless name and wireless password

Step3: After the configuration is completed, take a network line to connect the repeater’s LAN port to the router’s LAN port, and then connect the repeater’s SSID again to get online normally.

Packing list

**** 1

Frequently Asked Questions:

: After configuring the relay successfully, the extended wireless network

has been disconnected and SYS semaphores are not on. How to deal with this?

There are two situations that cause this problem: First, The repeater is too far away from the router and beyond the relay range; Second, The wrong wireless password was entered while configuring the repeater; Users can try to take the repeater to the socket near the router and plug it in. If the SYS signal light is still not on, you need to restore the repeater to the factory settings (press reset for 6 seconds) and then reconfigure it (the wireless password should be input correctly when checking the configuration)

A repeater that is already in normal use, what if you want to replace the

main route?

You need to Reset the repeater to factory Settings (long press Reset 6S) and then reconfigure it.

Other unknown problem that causes the repeater to be unable to use

normally, how to deal with?

You need to Reset the repeater to factory Settings (long press Reset 6S) and then reconfigure it.

How to operate WPS one-key connection?

It is required that the router also supports WPS function. After the repeater starts normally, press the WPS button of the repeater first, and the WPS indicator starts flashing. Then, press the WPS button of the router again within 2 minutes, and the automatic connection can be completed. After successful connection, there will be a suffix: ext-2G & Ext-5G wireless name, which can be reconnected (the wireless password is the same as the router's wireless password)

Warranty Terms

Warranty Terms

Dear customers:

Good day!

First of all, thank you for buying our products. Thanks again! In order to facilitate us to provide you with quality and satisfactory after-sales service, but also better protect your rights and interests. Please read this clause carefully.

Quality commitment:

The company adhering to the “user is God” purpose, to provide customers with quality and satisfactory after-sales service. All products sold by the company are guaranteed to provide free warranty service for one year.

The specific regulations are as follows:

1. Within one year from the date of purchase, our company will provide free warranty service for any defects that occur during normal operation under normal operating environment according to relevant technical information.
2. After more than one year from the date of purchase, our company will provide paid maintenance services.
3. If you buy our products, you can enjoy our most professional technical service support and provide the latest upgrade software package service for free.
4. Failure and damage caused by force majeure factors (such as fire, lightning, flood, etc.) are not covered by the warranty.
5. If the products within the warranty period are too damaged to be repaired or the accessories of this model have stopped supply, our company will provide other products of equivalent value for replacement. For the replaced products, if there is a price difference during the period, the price difference will be made up by the customer, and the replaced products will no longer enjoy the service of non-product fault replacement.
6. In case of any of the following circumstances, the products are not covered by free full warranty, replacement or return. Even if the products are within the warranty period, our company will charge relevant maintenance fees.
7. The repaired products have the following phenomena:

  * Burn marks
  * Defect or damage of components
  * Solder defects
2.  **Operational negligence includes:** If the crystal head is connected to the wrong wire, the product is damaged without wearing anti-static bracelet (for bare board), such as chip burning, whole machine damage, shield cover damage, radio frequency head damage, etc.;
3. Other problems and faults caused by abnormal use (mainly power supply or non-standard power supply);
4. Do not follow the installation and configuration instructions:
5. If the main board is so badly burned that it cannot be maintained, a new main board shall be purchased for replacement;
6. Damage caused by disassemble, repair or alteration of the circuit by the user;
7. Incomplete product information, such as warranty label /MAC address /SN code on the body, date paper removed, damaged or altered, model sticker removed;
8. Unauthorized modification of non-our company’s firmware.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>