menaco GEN 1.0 Multimedia Car Multimedia Software Instruction Manual
- June 14, 2024
- menaco
Table of Contents
INSTALLATION INSTRUCTIONS
MENACO GEN1 for KIA and HYUNDAI
Universal software package to run third‐party navigation software in standard car multimedia and navigation systems
SAFETY PRECAUTIONS
- For security reasons, and to avoid property damage, be sure to follow safety precautions when using the multimedia device (hereinafter referred to as the “headunit”), defined by the manufacturer or the dealer from whom you purchased the car.
- Software installation or update shall be made with the engine running. During installation do NOT turn off the engine, do NOT drive the car, do NOT switch a neutral transmission into reverse (switch to rear camera)! These actions may cause interruption of installation and completely destroy the headunit.
- Install the software and send the file to obtain a license key only on computers running Windows. MAC devices (iMAC when unpacking archives, iPhone when sending files) distort files and cause problems.
- Prepare a blank USB stick on 4‐32 GB (to store navigation maps, as well as your audio and video files). Familiarize the useful tips for USB Stick.
4 MAIN INSTALLATION STEPS
The Monaco installation process to the GEN1 headunit consists of 4 main steps:
- Check and update (if necessary) the current firmware version.
- Download the installation files and unzip them to the USB stick.
- Insert the USB stick drive into the USB connector of the car multimedia (automatic installation will start).
- Receive the license key and copy it to the USB stick.
THE CURRENT FIRMWARE VERSION UPDATE
The current firmware version detection
Before you install Monaco, make sure that the current original firmware
version is 7.7.4.
To do this, you must:
- Turn on the headunit with a power button and wait until it is loaded fully.
- Press and hold for 10 seconds the Gear button on the front panel of the headunit (if you have a car of 2010 or 2011, then the Setup button is instead of the Gear button).
- The screen displays the current firmware version (in the line “Software Version: …”)
The current firmware version update
To update the current firmware version choose one option that suits you out of
5 possible below:
- If the current firmware version is lower than 5.1.3, then first you need to update the current version to 5.1.3, and then to 7.4.5. After that update 7.4.5 to version 7.7.4. For updates use the Firmware Upgrade Instruction (see below).
- If the current firmware version is lower than 7.4.5, then update it to 7.4.5. Then update the firmware 7.4.5 to version 7.7.4. For updates use the Firmware Upgrade Instruction (see below).
- If the current firmware version is lower than 7.7.4, for example 7.5.A, 7.6.5, then update it to 7.7.4. To update use the Firmware Upgrade Instruction (see below).
- If the current firmware version is 7.7.4, then you do NOT need to perform any update, go to the INSTALL MENACO section below.
- If the current firmware version is 7.8.3 or higher, then downgrade the firmware to 7.7.4. To downgrade use the Firmware Downgrade Instruction (see below).
Firmware UPGRADE Instruction
-
Download the appropriate file to your computer from the link below.
Original firmware 5.1.3 http://narod.ru/disk/20298639001/нави.zip.html
Original firmware 7.4.5 https://yadi.sk/d/ee_Y0D‐zSui2qQ
Original firmware 7.5.8 https://yadi.sk/d/6OBGDDJEiGmVX
Original firmware 7.7.4 https://drive.google.com/file/d/1T_e4Kq8nqnXT0zUuQ8ntSHsWn48NmTt‐/view?usp=sharing -
Unzip the archive file to the root directory of the USB stick.
-
Start the engine of your car (DO NOT turn off during installation), turn on the headunit and insert the USB stick into the USB slot of the car.
-
You will be prompted to update. Confirm to update.
-
After a successful update, the radio will reboot and offer the update again. Click cancel.
Firmware DOWNGRADE Instruction
- To downgrade the firmware from ver. 8.2.3, 8.0.6, 7.9.4, 7.8.3 to ver. 7.7.4 use the following link and instructions https://yadi.sk/d/ht33AgmmgOEprQ
- Download the archive file force‐7.7.4.rar to the PC.
- Unzip the archive file to the root directory of the USB stick.
- Start the engine (DO NOT turn off during installation), turn on the headunit and insert the USB stick into the USB slot of the car.
- Version 7.7.4 will be installed automatically (the following messages can appear in 10 seconds: “Update is not compatible! A new or identical version of the map has been found, click Accept” or “The firmware version for update is 9.9.9”).
- Press ОК, wait for the end of upgrade progress.
INSTALL MENACO
-
ATTENTION! Installation of Menaco is only possible over the original firmware version 7.7.4!
-
Unzip the archive file LG8900‐LG2100‐USB‐xxx.rar (password for the archive: menaco) to the PC. Copy internal folders and files to an empty USB stick formatted in FAT32 and volume of not less than 4 Gb.
-
Unzip the archive file LG8900‐2100‐HMC‐ххх.rar (for Hyundai) or LG8900‐2100‐KIA‐ххх.rar (for Kia) to the PC (Note: xxx indicates the release number). Copy internal folders and files to the USB stick.
-
Check that after unpacking both archives, the following folders and files should be on the USB stick (in the root directory):
-
Start the engine, switch on the headunit and insert the USB stick into the slot next to the lever of the CPR.
-
If everything is done correctly, you will see the Monaco Installer message. Wait till completion of operation (the INSTALL SUCCESS message) and automatic reboot. If the installer shows an error – turn off the ignition for 15 minutes (to reboot the headunit). Switch on the ignition. Switch on the headunit. Remove the USB stick and turn off the ignition. Send the menavrus‐install.log file (this file is created automatically in the root directory of the USB stick) to e‐mail support@menaco.by (technical support).
-
If the Installer does not show errors and the headunit rebooted, wait until it is loaded fully (Monaco firmware is installed but the headunit menu stays unchanged until the license file is copied to the USB stick). The meandrous. did file shall appear in the Menara’s/ folder on the USB stick. Turn off the ignition. Remove the USB stick. Check this file.
-
meandrous. did file is required to obtain the Monaco license file of meandrous. lic. Go to the Menaco License page and submit this file by filling out the special form.
-
In a reply letter (over time), you will receive a license file meandrous. lic. Copy it to the Menara’s/ folder on the USB stick. Please note that you do not need to remove meandrous. did file or others from the USB stick.
-
Copy the maps files from the PC to the certain folder on the USB stick (the set of programs depends on the ordered completion of Menaco). For Navitel you can create the required folder in the root directory of the USB stick manually, or this folder will be created later when you start Navitel for the first time):
for Novatel (file .nm7) to folder Navitel Content\Maps\;
for 7ways (files .7w and/or *.dat) to folder 7ways\Maps\. -
a). Car engine must be turned off at least 15 minutes (to restart the headunit).
b). Insert USB stick into the slot next to the lever of the CPR and switch on the headunit.
c). File initialization occurs. Monaco is installed. -
To verify that Monaco is in service click a Map button (or 5 times on the Gear button to start the new
software) ‐ you should see the Monaco Menu with the buttons for additional programs.
Note: If Monaco does not start after Clause 10, please format the USB stick (or take a new one) and install Monaco starting with Clause 2 again. Please note that a license file meandrous. lice will remain the same (save it first).
START / DISABLE MENACO
Menaco Menu contains the Multimedia Player button, one or two Navigation
Software buttons, and a button of the Total Commander file manager (for
advanced users only!). Instructions to access the file manager see below.
If you need to switch from Menaco to the original firmware, press 5 times the
Gear button, and then click Addon Off and Apply. The headunit will reboot
into standard navigation program and will work as if you were using the
original firmware.
Reverse switch to Menaco is similar by clicking Addon On and Apply.
Note:
Composition, location and image of the Monaco Menu buttons depend on
the ordered completion of Monaco package, as well as the country of
supply.
USE OF MENACO
Monaco performs the following main actions when you press headunit buttons:
- Press Voice Info (the centre of the second regulator in some headunit) – displays the Monaco Menu with the ability to run additional programs. In case if you are running a navigation program, this button recalls the relevant menu navigation program.
- Press the buttons of Nav, Map, Info – this runs the program specified in the configuration file, if any program is running ‐ you call the Search Menu of this program.
ACCESS TO THE MENACO FILE SYSTEM
Attention! Warning! The Total Commander CE file manager is included in
Monaco .
In no case, do not perform any operations on the Storage Card/System folder,
this may completely disable the headunit operability! Also, you cannot
format the Storage Card partition!
Use a File Manager with caution, do not remove or replace any files on the
internal memory of the headunit, if you are not sure what you are doing. This
can lead to the complete unavailability of the headunit.
All the ways to run programs can be configured in the /Storage
Card/meandrous/meandrous. cog file. Edit this file carefully, without breaking
syntax.
To close random access to the Total Commander CE, rename (or delete) the file
of total.exe in the folder of Update/ on the USB stick.
DELETE MENACO
To completely remove Monaco from the headunit, install the the original
firmware 7.7.4.
SETTINGS OF MENACO
Description, features, settings and recommendations for Monaco GEN1 are
given in User Manual for Monaco GEN1.
Note:
The Monaco GEN1 User Manual is provided in the Russian language and prepared
in .pdf format.
Please translate this document into your preferred language using this link
https://www.onlinedoctranslator.com
In case of any translation misunderstanding please do not hesitate to contact
us mail@menaco.co.
Wide Road Ltd. © 2014‐2022
The rights to the content of this document, its reproduction in whole or in
any part thereof, its publication and distribution belong to Wide Road, Ltd.
Law on trademarks and trademarks shown are stored for their respective owner.
References
- Free Online Translator - Preserves your document's layout (PDF, Word, Excel, PowerPoint, OpenOffice, text)
- force-7.7.4.rar — Yandex Disk
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>