CHUHAITONG HW8808 Remote Control Car User Manual

HW8808 Remote Control Car
User Manual

HW8808 Remote Control Car

Cautious

1. Small parts, please keep them out of access of children.
2. Please operate in the open field without any electromagnetic interference.
3. Discarded batteries should be safely disposed, do not dispose them arbitrarily.
4. Please store the car and remote control in a dry and cool environment.
5. Keep away from fire, high temperature and humid environment.
6. If the car battery is wet, be sure to dry it thoroughly to avoid damage.

Notice

• Please pay attention to the polarity of the battery when installing or replacing the battery, non–rechargeable batteries cannot be charged
• When not in use for a long time, the battery should be removed from the car and remote control
• This manual should be kept for future reference

Product configuration

Remote control battery installation

Battery installation diagram

1. As shown in Figure 1, open the battery cover.
2. As shown in Figure 2, install 3 4.5V AA batteries. (Pay attention to the polarity of the battery, do not install it in reverse)
3. As shown in Figure 3, close the battery cover.

Notice

1. When installing the battery, make sure that the battery holder is marked with the match the polarity.
2. Do not mix old and new batteries.
3. Do not mix different types of batteries.
4. If the remote control is not used for a long time please remove the battery

Remote control car battery installation

1. As shown In Figure 6. remove the car body, open the battery compartment and place the battery into the compartment.
2. a) Insert the USB airbed into the USB port of a computer or an AC adaptor, you will see USB indicator light flashes red slowly; then connect the battery to USB cable, the USB light will be on. that means battery is being charged. The whole charging process will take 5 hours approx. Charging finished when the USB light turn off.
3. As shown in Figure 7, connect the socket of the rechargeable battery pack to the car
4. As shown In Figure 8. opt the battery holder upwards and rotate it to the outside. At this time, put the battery into the bottom of the vehicle and rotate the battery holder inward to dose the battery compartment.

• Press and hold the power switch of the car for 2 seconds to turn on the power, and then press and hold the power switch for about 3 seconds to him off the power.

Charger or battery pack precautions

1. In order to prevent the lithium-on battery pack from being damaged or exploded due to over-charging, the charger adopts a voltage-limiting protection device. And to maintain the chargeability and performance of the battery pack, we recommend not charging for more than 24 hours continuously.

2. The battery adopts a low-voltage power supply over-discharge protection device. When the battery is over-discharged, it needs ta be recharged to activate the battery. It is recommended to ramie the battery and turn the switch to “OFF” when the car is not in use.

3. The circuit board has overheat protection function. When the board overheats. the car will be unusable (hold on for 3-6 seconds to recover)

4. Function Introduction diagram of tire mercer cnnlml

• Recomrnonded for boginnortt, s2ow down, Wen and operate.

1. Speed trimming
   Turning the accelerator clockwise makes the car go faster, turning the accelerator countercloclomse makes the car go slower.

2. Left) Right trimming
   When the vendee is leaning to the left, t should be rotated clockwise to adjust, and when the vehicle Is leaning to the right, it should be rotated and adjusted counterclockwise.
   • Please turn the steering trim adjustment slowly until the car runs straight
   Nobel:. Where thane le no opervians on remote control for 10 minutes, the cero will enter sleep mode, and it cant be controlled. At thief time. you have to tum. on the peer enrich for restart the car again.

3. The frequency of the car is synced with the remote control
   a) Where sync rig for the first lime, Ong press to turn on the car and ten remote control to sync the frequency. During the syncing croons, the green light at the remote control will lash alternately Attar successful Beynon, Me green light will be on.
   b) Where syncing free. ‘Tientsin’s. please do nil laud’ the remote mount with anything Lc ensure that the position of the remote credo’s does nil deviate.
   c) It the syncing is unsuccessful, Pease turn Mt the car and the remote control anon sync again.

4. How to operate the car.
   a) Put the acce4emlor back and the car rnavevc forward.
   b) Push the accelerator forward and the car goers backwards.
   c) Pull the aocwerator beck the remote control dial rotates counterclockwise, and the car turns left while moving forward,
   d) Pull the oscillator back the remote control diet rotates clockwise. and the car turns right while moving forward. e) Push the acrtieralnr forward, the rennin axed dial Maben countercicckwise, ance the car turns left whit moving backwards.
   f) Parch the accelerates- fnrwarci, the roman cried dot retains clockwise, and the car turns right while rnyek-ig backwards.

Notice: When the power of the car or the remote control is insufficient, the LED light on the car or the remote control will flash slowly. please charge or replace the tatter), in Mie.

Assembly View-A

Assembly View-B

Assembly View-C

Assembly View-D

Assembly View-E

Assembly View-F
Assembly View-G
Assembly View-H
SPART PART LIST-1

SPART PART LIST-1
SPART PART LIST-1

FCC Warning

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, macaques harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmfulinterference to radio or television reception, which can be determined by turning the equipmentoff and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Caution: Any changes or modifications to this device not explicitly approved by manufacturer could void your authority to operate this equipment.
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 0cm between the radiator and your body.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>