greenworks 2961702 24V Battery Charger User Manual

**greenworks 2961702 24V Battery Charger User Manual

**

IMPORTANT SAFETY INSTRUCTIONS

WARNING
TO REDUCE RISK OF FIRE OR ELECTRICAL SHOCK, CAREFULLY OBEY THESE INSTRUCTIONS.

• Do not cover the ventilation slots on the top of the charger. Do not set the charger on a soft surface i.e. blanket, pillow. Keep the ventilation slots of the charger clear.

• Confirm the voltage availability at each country location before using the charger.

• If the shape of the plug does not fit the power outlet, use an attachment plug adaptor of the proper configuration for the power outlet.

• DO NOT allow liquid inside the charger.

• DO NOT try to use the charger for any other purpose than what is presented in this manual.

• Unplug the charger and remove the battery pack before cleaning.

• Do not try to connect two chargers together.

• Do not use the charger in the circumstances that the output polarity does not match the load polarity.

• For indoor use only.

• Do not place the battery pack in the sun or in a warm environment. Keep at normal room temperature between 6 °C and 40°C.

• Do not allow small metal items or material such as steel wool, aluminum foil, or other foreign particles into the charger cavity.

• Do not attempt to recharge non-rechargeable batteries with the charger.

• SAVE THESE INSTRUCTIONS-This manual contains important safety and operating instructions for battery charger Model 29972/CAG801/CAG813/2903102/ 29862/2978602.
  Before using battery charger, read all instructions and cautionary markings on battery charger, battery, and product using battery.

• CAUTION-To reduce risk of injury, use only LB24A020 or Green works 24V series approved replacement batteries. Other types of batteries may burst causing personal injury and damage.

• This appliance can be used by children 8 years of age and older. Individuals with reduced physical, sensory or mental capabilities or lack of experience and knowledge, should only use this appliance with supervision, and/or proper instruction concerning the use of this appliance in a safe way and understand all hazards. Children shall not play with the appliance. Cleaning and user maintenance shall not be made by children without supervision.

• If the cord set is damaged, it must be replaced by a special cord set available form the manufacturer or its service agent.

WARNING
To avoid risk of fire, electrical shock, or electrocution:

• Do not use a damp cloth or detergent on the battery or battery charger.
• Battery should be no where near a water source
• Always remove the battery pack before cleaning, inspecting, or performing any maintenance on the tool.

SPECIAL RULES FOR CHARGER

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

• Appliance shall not emit harmful radiation or present a toxic or similiar hazard due to their operation in normal use.
• This device must accept any interference received, including interference that may cause undesired operation.

CAUTION
Changes or modifications not expressly approved by the party responsible for compliance could void the user’s
authority to operate the equipment.

NOTE
This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules.

These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio or television reception. The reception can be determined by turning the equipment off and on. The user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

PROPOSITION 65

WARNING
This product contains a chemical known to the state of California to cause cancer, birth defects or other reproductive harm. Some dust created by power sanding. sawing, grinding, drilling, and other construction activities contains chemicals known to cause cancer, birth defects or other reproductive harm. Some examples of these chemicals are:

• Lead from lead-based paints;
• Crystalline silica from bricks and cement and other masonry products; 6 OPERATION
• Arsenic and chromium from chemically treated lumber.

Your risk of exposure to these chemicals varies depending on how often you do this type of work. To reduce your
exposure to these chemicals, work in a well-ventilated area, and work with approved safety equipment, such as dust masks that are specially designed to filter out microscopic particles.

SYMBOLS ON THE MACHINE

You can use below symbols on the machine. Please study  them and learn their definitions. Correct interpretation of these symbols let you operate the tool better and safer.

RISK LEVELS

The following signal words and meanings are intended to explain the levels of risk associated with this product.

avoided, will result in death
or serious injury.
| WARNING| Indicates a potentially hazard ous situation, which, if not
“avoided, could result in death or serious injury.
| CAUTION| Indicates a potentially hazard- ous situation, which, if not avoided, may result in minor or moderate injury.
---|---|---
| CAUTION| (Without Safety Alert Sym- bol) Indicates a situation that may result in property dam- age.

OPERATION

CHARGE PROCEDURE

NOTE
Before use charge the battery pack fully to make sure that the battery pack can get the maximum run time. This battery pack does not have a memory. You can charge it all the Time

1. Connect the plug of charger (2) to an AC power outlet
2. Put the battery pack (1) into the charger (2)

This is a diagnostic charger. The Charger LED Light (3) illuminates in a specified order to show the current battery status. They are as follows:

For charger: 29972/2978602

For charger: CAG801/2903102/29862

For charger : CAG817/CAG812

CHARGING PROCEDURE (LED INDICATOR)

BATTERY IS CHARGING|
GREEN BLINKING
FULLY CHARGED| GREEN

BATTERY IS TOO WARM (REMOVE FOR APPROX. 30 MINUTES . TO ALLOW TO COOL)| RED

DEFECTIVE BATTERY (REMOVE AND REPLACE WITH A NEW BAT- TERY)|
RED BLINKING

1. Put the battery pack into the charger
   • If the status LED blinks RED, remove the battery pack from the charger for 1 minute.
2. Put the battery pack into the charger again.
   • If the status LEDs show correct, the battery pack is good.
   • If the status LED stays blinking RED, remove the battery pack and disconnect the charger,
3. Wait for 1 minute and put the battery pack into the charger again.
   • If the status LEDs show correct, the battery pack is good.
   • If the status LED stays blinking RED, the battery pack is defective and it is necessary to replace the battery pack.

EXAMINE THE CHARGER

If the battery pack does not charge correctly:

1. Examine the current of the power outlet with different machines. Make sure that the outlet works.
2. Examine that the charger contacts are not short-circuited.
3. If the charger is not under usual room temperature, move the charger and battery pack to a location where the temperature is between 6° C to 40° C (42.8 F to 104 F).

WARNING
If you attempt to charge the battery pack in a warm or hot environment, and the charger LED light is red, remove the battery pack and let the battery cool for approximately 30 minutes

MOUNT THE CHARGER

1. Get the location of the wall to attach the charger.
2. Use 2 wood screws to attach the charger on the wood studs.
3. For charger CAG801/2903102/29862: Drill two paralleled holes 57 (127 mm) on center. For charger CAG817/ CAG812: Drill two paralleled holes 4.4 (112 mm) on center.
4. Use wall anchors and screws to attach the charger to the drywall.

CAGR01/2903102/29862

CAGR17/ CAG812

NOTE
If you do not use the battery pack and charger for a long time, please remove the battery from the charger and pull out the AC power plug.

MAINTENANCE

CLEAN THE MACHINE

NOTE
Keep the air vent free of blockage, saw dust, and wood dust. Do not spray, wash, or submerge in water.

• Clear the unwanted material out of the air vent with a Vacuum
• Clean housing and the plastic components with a soft, dry cloth

IMPORTANT
Do not use strong solvents or detergents on the plastic housing or components.

STOW THE MACHINE

• Remove the battery pack before you store the charger or disconnect the charger.

TROUBLESHOOTING

pack or charger is defective or there is a bad connection be tween the battery pack and charger.| Try to remove and reinsert the battery pack in the charg- er.
Try charging a dif- ferent battery pack
Unplug the charg- er and wait until the red LED goes out, then reconnect the plug to the power supply
Charger doesn’t work. Charger shows evaluation mode (LED indi- cates Red solid ON).| Battery pack is ei- ther too hot, or too cold.| Allow the battery pack to reach nor- mal temperature. Charging will be- gin when the bat- tery pack returns: to 3°C-47°C (37°F-117°F).

TECHNICAL DATA

TECHNICAL DATA (BATTERY PACK)

LIMITED WARRANTY

Greenworks hereby warranties this product, to the original purchaser with proof of purchase, for a period of three (3) years against defects in materials, parts or workmanship. Greenworks, at its own discretion, will repair or replace any and all parts found to be defective, through normal use, free of charge to the customer. This warranty is valid only for units which have been used for personal use that have not been purchased or rented for industrial/commercial use, and that have been maintained in accordance with the instructions in the owners manual supplied with the product when new.

ITEMS NOT COVERED BY WARRANTY:

1. Any part that has become inoperative due to misuse, commercial use, abuse, neglect, accident, improper maintenance, or alteration; or
2. The unit, if it has not been operated and/or maintained in accordance with the owner’s manual; or
3. Normal wea
4. Routine maintenance items such as lubricants, blade sharpening;
5. Normal deterioration of the exterior finish due to use or exposure

HELPLIN
Warranty service is available by calling our toll-free helpline at 1-888-909-6757.

TRANSPORTATION CHARGES:
Transportation charges for the movement of any power equipment unit or attachment are the responsibility of the purchaser. It is the purchaser’s responsibility to pay transportation charges for any part submitted for replacement under this warranty unless such return is requested in writing by Greenworks.

USA address:
Greenworks Tools
P.O. Box 1238
Mooresville, NC 28115

Canadian address:
Greenworks Tools Canada, Inc.
P.O. Box 93095, Newmarket, Ontario
L3Y 8K3

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>