DREO DR-HTF004S Smart Tower Fan User Manual
- June 14, 2024
- DREO
Table of Contents
DREO DR-HTF004S Smart Tower Fan
IMPORTANT SAFETY INSTRUCTIONS
READ ALL CAUTIONARY MARKINGS ON THE APPLIANCE AND SAFETY INSTRUCTIONS IN THE USER MANUAL BEFORE USE.
Do not cover the air inlet and outlet while in operation.
Do not use the fan near flammables and combustibles
General Safety
- Children shall not play with the appliance. Cleaning and maintenance shall not be performed by children without supervision.
- Use the appliance as described in the user manual only. Any other use not recommended in the user manual may cause fire, electrical shock, or personal injury.
- This appliance can be used by children aged above 8 years and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge if they have been given supervision or instruction concerning use of this appliance in a safe way and understand the hazards involved.
Operation Safety
- Place the appliance on a flat, dry surface before use.
- Do not immerse in water and any other liquids.
- Do not use the appliance until the base is installed.
- Do not insert your fingers, pencil and any other objects into the grilles while in operation.
- Do not dismantle, repair, or modify. All servicing should be performed by qualified personnel.
Electricity Safety
- Make sure that the voltage of your electricity supply is the same as that indicated on the appliance.
- Always unplug before cleaning or leaving the appliance unused for a long period of time. Keep your hands dry when plugging/unplugging.
- Do not operate any fan with a damaged cord or plug. Discard fan or return to an authorized service facility for examination and/or repair.
- Do not run cord under carpeting. Do not cover cord with throw rugs, runners, or similar coverings. Do not route cord under furniture or appliances. Arrange cord away from traffic area and where it will not be tripped over.
- WARNING: To reduce the risk of fire or electric shock, do not use this towerfan with any solid-state speed control device.
- 24V/1.5A power adapter only. Turn off the appliance before plugging.
- WARNING: To reduce the risk of fire, electric shock or injury to persons, do not use replacement parts that have not been recommended by the manufacturer (e.g. parts made at home using a 3D printer).
FOR HOUSEHOLD USE ONLY READ AND SAVE THESE INSTRUCTIONS
Gentle Reminder:
Check the appliance regularly and refer to TROUBLESHOOTING or contact our customer support if it shows any of the following signs:
– Power cord or plug is damaged.
– Loud noise, unusual smell or excessive heat.
Specifications
Model
|
DR-HTF004S
---|---
DR-HTF004S| DR-HTF004S
DR-HTF004S| DR-HTF004S
Power Adapter| Input: 100-240V
~50/60Hz
Output: 24V=1.5A
Battery Type| ASSEMBLING YOUR TOWER FAN
ASSEMBLING YOUR TOWER FAN
Assembly Instructions
When using the appliance for the first time, remove the wraps and attach the parts by following the steps below.
Keep two base halves upside down and hold them in a crossed position, then insert the pegs on one half onto the slots on the other half.
Press down on the joint areas as shown to click two base halves together.
Remove the screw nut on the bottom of the fan by rotating it counterclockwise.
Fit the base onto the fan and secure by screwing the nut back on.
Put the fan upright, then plug the power adapter into the power input (located at the back of the fan), and into the power outlet.
CAUTION
Do not operate the tower fan if the base has not been installed.
Package Contents
CONNECTING TO YOUR TOWER FAN
Before connecting the appliance to your mobile device, please scan the QR code
on the left or go to the app store and search” Dreo”, then select and download
the app.
You can use the Oreo app to connect your smart tower fan to Amazon Alexa
or Google Assistant. Please follow the in-app instructions to set up your
voice assistant.
NOTE: You must create a Oreo account to access voice assistants.
- Launch Oreo and sign in or create account by following in-app instructions.
- Enable Bluetooth on your mobile device and plug in your tower fan.
- Tap + Add Device and select the tower fan you want to link.
- Hold the Oscillation button for 5 seconds to start WiFi connection settings. The WiFi icon will keep flashing when pairing.)
- Follow in-app instructions to complete WiFi connection.
- You’re now ready to control the appliance on your app. To restart connection settings, hold the Oscillation button again for 5 seconds.)
KNOWING YOUR TOWER FAN
Control Panel
Power Button Turn power on/off
Mode Button
- Switch between Norma V Natura V Sleep Auto Mode
- Long press to mute/unmute
Oscillation Button
- Select to start/pause oscillating
- Long press 5 seconds to start network settings and device pairing
Decrease Button Decrease fan speed (1-12 levels)
Increase Button Increase fan speed (1-12 levels)
Timer Button Select to set a timer (0-12h)
NOTE: Long press and at the same time for 5s to reset to factory settings.
LED Display
NOTE: This tower fan features auto-brightness. The display adapts automatically based on the ambient lighting conditions.
Getting the Most out of Your Tower Fan
- It’s not an air conditioner.
- Remove any tall obstacles that might block the airflow from the fan.
- Combine with your AC unit to get cooler air throughout the room.
- Position the tower fan closer to you to get more direct airflow.
- Place a bucket of ice in front of the fan for an extra cooling boost.
USING YOUR TOWER FAN
General Operations
- Touch to turn on, and to choose a working mode.
- Touch or to adjust the airflow volume.
- Touch to change the airflow direction.
- Touch to set a timer.
- Touch to turn off the tower fan.
Working Modes
Sleep Mode (Mute Auto On)
Fan speed decreases every 30 minutes.
Speed decreases by three or two levels at most and will remain
constant if at level 3, 2 or 1:
For level 12: 12-11-10-9
For level 11: 11-10-9-s
For level 10: 10-9-s-7
For level 9: 9 …. g …. 7 …. 5
For level 8: g …. 7 …. 5
For level 7: 7 …. 5 …. 5
For level 6: 5 …. 5 …. 4
For level 5: 5 …. 4 …. 3
For level 4: 4 –s
For level 3: 3
For level 2: 2
For level 1: 1
Auto Mode
Fan speed adapts to the ambient temperature.
Normal Mode
Fan runs at the constant speed.
Natural Mode
Fan runs at alternating speeds.
Additional Features
- The oscillation angle can be set to 30/60/90/120 degrees.
- To use this feature, please go to the Oreo app.
When the fan is ON/OFF, touch the timer button (9 repeatedly to set a timer from 1 to 12 hours. When the timer ends, the fan will stop/start running automatically. To cancel, set the time to O hour. Note: When the auto off timer is enabled, display will return to fan speed after 3 seconds.
Method 1 : Short press the mute button ~x on the remote control to
turn on/off button sounds.
Long press the mode button 8 on the Method 2 : control panel to turn
on/off butl:6n sounds.
If the fan is turned OFF or disconnected from power, it will operate under the previous settings (except the timer setting) when it is turned ON again .
Remote Control
Battery Replacement
- Press the locking button to pop out the battery holder.
- Replace with the same battery type with the(+) side facing up.
- Push in the holder until securely locked into place.
Note: If the indicator on the remote control doesn’t turn on any more, please consider replacing the battery.
WARNING
Chemical Burn Hazard. Keep batteries away from children. This product contains
a lithium button/coin cell battery. If a new or used lithium button/coin cell
battery is swallowed or enters the body, it can cause severe internal burns
and can lead to death in as little as 2 hours. Always completely secure the
battery compartment. If the battery compartment does not close securely, stop
using the product, remove the battery, and keep it away from children. If you
think batteries might have been swallowed or placed inside any part of the
body, seek immediate medical attention.
The batteries must be disposed of properly, including keeping the ma way from
children. Even used cells may cause injury.
CLEANING AND MAINTENANCE
Outer Surface
Gently wipe off the dust with a soft, dry cloth\
Base
The base can be disassembled in the reverse order of assembly.
CAUTION
- Always unplug the fan before any cleaning or maintenance to avoid the risk of fire, electric shock, or injury to persons.
- Do not immerse in water or get water inside the motor housing.
- Do not use any chemical agents when cleaning the fan.
- Store in a cool, dry place and cover it to protect from dust.
Rear Grille
WARNING
Turn off the appliance and unplug before any cleaning and maintenance.
Remove the screw on the top of the rear grille with a Philips screwdriver.
Lift up the grille and pull it out.
Clean the dust on blades using a vacuum cleaner or air duster.
Rinse the rear grille under running water or with a clean, damp cloth.
Dry up, then install the grille and the screw back in place, making sure the
bottom pegs are fully inserted into the slots.
TROUBLESHOOTING
My fan won’t turn on!
- Make sure that the cord is connected to a powered outlet and the mains voltage corresponds with the voltage indicated on the fan.
- Check if the power adapter is securely inserted into the power out let and the tower fan.
- Protection may have been activated. Please unplug the tower fan and let it rest for 10 seconds before re-plugging in.
My fan is shaky and wobbling
- Place the fan on a flat, level surface.
- Incorrect installation might also cause shakiness. Please refer to the assembly instructions in page 3-4.
My fan is making vibration and noise
- Place the fan on a flat, level surface.
- Be sure not to insert anything into the air inlet and outlet.
If your problem is not listed or still persists, please contact our Customer Support (see page 15).
FCC STATEMENT
This device complies with Part 15 of the FCC Rules.
This equipment has been tested and found to comply with the limits for a
Consumer ISM equipment, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
Please note that changes or modifications of this product is not expressly
approved by the party responsible for compliance could void the user’s
authority to operate the equipment.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
- Reorient or relocate the receiving antenna.
- Increase the separation between the equipment and receiver.
- Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
- Consult the dealer or an experienced radio/f V technician for help.
courier service
888-290-1688 support@dreo.com www.dreo.com
Shenzhen Hosing Innovation el Technology Co., LTD
26F, Bldg. A7, Creative City, Shenzhen, China MADE IN CHINA
LISTED E219869