VIVIDMOO C1KfGOoyfgL Cold Press Whole Slow Juicer Instruction Manual

COLD PRESS WHOLE SLOW JUICER MANUAL

• Read this manual carefully to understand the operation of your Cold Press Juicer
• You can visit our website www.vividmoo.com

SPECIFICATIONS

IMPORTANT SAFEGUARDS

When using electrical appliances, basic safety precautions should always be followed including the following:

1. Read all instructions.
2. To protect against risk of electrical shock, do not put motor or base of unit in water or other liquid.
3. Keep away from children.
4. Unplug from outlet when not in use, before putting on or taking off parts, and before cleaning!
5. Avoid contacting moving parts.
6. If the supply cord is damaged, it must be replaced by the manufacturer, its service agent or similarly qualified persons in order to avoid a hazard.
7. The use of attachments not recommended or not sold by the manufacturer may cause fire, electric shock or injury.
8. Do not use outdoors.
9. Do not let cord hang over edge of table or counter.
10. Always make sure juicer body is clamped securely in place before motor is turned on.
11. Be sure to turn switch to “O” position after each use of your juicer. Make sure the motor stops completely before disassembling.
12. Do not put your fingers or other objects into the juicer opening while it is in operation. If food becomes lodged in opening, use food pusher or another piece of fruit or vegetable to push it down. When this method is not possible turn  the motor off and disassemble juicer to remove the remaining food.
13. Do not use the appliance if the rotating sieve is damaged.
14. When a separable pulp container is provided, do not operate without the pulp container in place.
15. Please do not alter the appliance in anyway.
16. Do not use the appliance for anything other than it’s intended purpose as described in the manual.
17. The appliance should be used for limited period of time.
18. This appliance cannot be used by children and persons with reduced physical, sensory or mental capabilities or lack of experience and knowledge. Children shall not play with the appliance. Cleaning and user maintenance shall not  be made by children.

SAVE THESE INSTRUCTIONS

• This appliance is for household use only. Please carefully follow the instructions in the manual.
  (The appliance cannot be covered under the manufacture warranty if the product is abnormally or commercially used.)

• Save the instruction manual for future reference.

• If the appliance is given away as a gift, please include the manual with the product.

SAFETY WARNING
The following precaution is provided to ensure the safety of the user. Please carefully read through the precautions and exercise a degree of care when using the appliance.

Warning : Warns risk of death of severe injuries.
Caution: Warns risk of injuries or appliance damage.

Do not put any non-food items into the Main Juicing Body/Feeding Chute.
This juicer is only designed to juice fresh fruits and vegetables. Do not use frozen fruits or vegetables.
Make sure that the surface where the appliance operates is stable, level, clean, and dry. Vibration may occur during regular operations.
Do not operate the juicer for more than 15 minutes at a time when juicing at a rapid rate or with firm pressure.
Allow the motor to rest for 1 minute between each use.
Equipped with an intelligent, protective chip, the appliance will stop automatically after 20 minutes of continuous operation.
In this case, wait for the motor to cool down before use to prolong the service life of the appliance.
Please refer to the juicing tips, troubleshooting, and care and maintenance sections for tips and best practices to ease your interaction with the product.
Do not plug multiple power cords on a single outlet during operation.
➔ It may cause an explosion or fire.
Do not touch the power cord with wet hands.
➔ It may cause electrical shock.
Do not leave the appliance unattended. Unplug the power cord from the outlet when not in use.
Use a dry towel to clean the power cord if it is dirty or wet.
➔ It may cause electrical shock or fire.
Do not drop the appliance nor inflict strong force to the appliance.
➔ It may damage or break the appliance.
Do not unplug by pulling off the power cord cable.
➔ It may damage the power cord and cause electrical shock o not put your finger or other objects into the feeding tube while it is in operation.
➔ It may cause injury.
Do not put the parts in the dishwasher or extremely hot water.
➔ The parts may wear faster.
Do not repair, disassemble the body, or customize the appliance.
➔ The appliance may not operate properly causing fire, electric shock, or injury.
Do not use the appliance on an uneven surface.
➔ It may cause a malfunction if the appliance tips over.
Keep away from children and store the appliance in a safe place.
➔ It may cause injury.
Please do not store or operate the appliance nearby heating appliance.
➔ The appliance may become discolored or deformed
Do not use any hazardous chemicals to clean the appliance or spray flammable sprays near the appliance.
➔ It may change the color of the appliance or could result in a fire.
To protect the power cord, please do not aggressively bend or put heavy object on top of the power cord.
➔ It may cause short circuit or even fire.
Operating the juicer without ingredients can cause damage to the screw.
Don’t forget to disconnect the power supply before dismantling, assembling, or adjusting any part of the appliance.
Do not let the power cord touch hot surfaces, including the stove, or become knotted or tangled. Do not place heavy objects on the power cord. Make sure you position the power cord such that it Wail not be stepped on or tripped over

PARTS

HOW TO ASSEMBLE

Check Before Operating
Wash the parts before first use.

1. Before starting assembly, ensure that the appliance is unplugged and the power switch dial is set to off or 0.”
   Note The Juicer may leak if not assembled properly.

2. Fit the Main Juicing Body into the motor base, making sure to see that the hexagonal shaft of the metal lever on the Auger/ Spiral is properly aligned with the socket on the motor base. Keep inserting the metal lever until you hear  a “click’ sound

3. Insert the Auger/ Spiral into the Main Juicing Body/ Feeding Chute.

4. Fit the Filter/ Strainer over the Auger/Spiraland rotate the attachment back and forth, if necessary.
   Align the two arrows on each part and assemble in the picture shown.

5. Attach the End Cap to the Main Juicing Body, and turn anti-clockwise until the triangle alignment mark(arrow) is set to lock.
   

6. Place the Juice Container under the spout in the designated groove, and align the Juice Residue Cup under the pulp spout.

7. Place the Pushing Rod into the Main Juicing Body.
   Keep the smart cap open when juicing.
   The juicer is now ready to be operated.

BUTTON OPRATION

The power switch has 4 settings.

1. ON/OFF Turns off the machine.

2. Hard: High power use for harder fruits/vegetables( e.g Apples, celery, carrots)
   

3. Soft: Low power use for softer fruits and vegetables (e.g. Oranges, grapes, berries, melons)

4. REV: Reverse rotation(only used to prevent clogging)

HOW TO OPERATE

STEP 1 After preparing the ingredients, plug the power cord into a wall outlet.
Note

• • Do not touch the power cord with wet hands. It may cause electrical shock, short-circuit, or fire.
• Ensure the power cord is plugged into a power outlet.

STEP 2 Press the SOFT/HARD button to operate.
Note

• SOFT/HARD: Pulls down and slowly masticates the ingredients.
• REV: Pushes the ingredients back up to dislodge them.

If the ingredients become jammed in the screw and the drum lid does not open, press the “O” button. Then press and hold the REV button until the ingredients become dislodged.
Repeat REVERSE – O-SOFT/HARD as often as needed to achieve the desired result.

If the juicer stops during operation:

Switch the button to O position then press and hold the REV button until the ingredients become dislodged.
Repeat REV – O-SOFT /HARD as needed.
SOFT/HARD: Pulls down the food
0 : Stops the operation
REV: Pushes the food back up

Note

• REV: Pushes the ingredients back up to dislodge them.
  The REV button only works while holding down the switch.

• Switch O ensuring that the juicer comes to a complete stop. Then press REV .
  Hold the REV button for 2-3 seconds and release. Repeat as needed. Let the juicer stop completely before using the REV button to prevent malfunction.

• If the juicer does not work after these steps, disassemble and clean the parts before operating the juicer again.

STEP 3
Insert the prepared ingredients into the feeding tube, one piece at a time.

Note

• Fibrous leafy vegetables (celery, kale, etc.):
  » Separate each stem. Cut the outer stems that are thick and tough to 2 inches long or less.
  » Bundle up the leafy vegetables as inserting into the juicer. Alternate between leafy parts and stems.

• Before extracting, remove hard seeds or pits in ingredients.

• When juicing frozen fruits with small seeds, ensure that even the seeds are completely thawed.

• Insert the ingredients one piece at a time.

Tip

• After inserting ingredients, use the pusher when it is necessary. Too much use of the pusher may affect the juice quality.
  » Intermittently use the pusher for soft ingredients like tomatoes and apples. Constant use of pusher for soft ingredients may affect the juice quality.

STEP4
Use the smart cap to stop juice from dripping, or rinse between different juices.

Tip

• After juicing, close the smart cap to stop the juice from dripping, especially when disassembling the juicing bowl off the body.
• When making different juices quickly rinse away any leftover flavors by running a glass of water in the juicer with the smart cap closed.
• Leave the smart cap open when juicing ingredients that create excessive foam during extraction, (e.g. apples, celery).

Note

• Pay close attention when operating with the smart cap closed. Juice may overflow if the juice collected in the juicing bowl exceeds its capacity marked on the bowl.

STEP 5 After juice and pulp are completely extracted, switch the unit OFF.

Note

• If the remaining ingredients in the juicing bowl have not been extracted completely, the main body may not open easily. After each extraction, run the juicer for an additional 30 seconds to let the juicer extract the remaining pulp.
• When the juicer is stuck, press the REV – O-SOFT/HARD button in this order; switching back and forth 2 or 3 times to dislodge the ingredients.

TIPS ON OPERATION

1. Operating the juicer without ingredients can cause damage to the screw.

2. Do not continuously operate the juicer for more than 15 minutes.
   This can damage the motor from overheating. After continuous use, let the juicer rest for 1 minute to cool down before starting another session.

3. Do not put hand, utensil, tong, or other objects into the feeding tube other than the provided pusher.

4. During operation, do not put spoon, spatula or other objects into the juice spout of the juicing bowl.
   If other object is put into the juice spout during operation, such materials can get stuck and damage the juicer parts.

5. Do not put dried whole grains, fruits with hard seeds or ice.
   These may damage the juicer parts (e.g. juicing bowl, juicing screw, and strainer).
   · Beans or grains can be used if soaked overnight or boiled.
   · Fruits with pits and hard seeds (e.g. nectarines, peaches, mangoes and cherries) must be pitted before juicing.
   · When using frozen fruits with small seeds such as grapes, completely thaw before inserting them into the juicer.
   · Use of ice in the juicer will decrease the product durability over time.

6. Do not use ingredients containing excessive amounts of vegetable oil or animal fat. Do not use the juicer to extract vegetable oil from ingredients.
   If vegetable/animal oil gets on the juicing screw, it may reduce performance and even damage the part.

7. After juicing ingredients with seeds like grapes, thoroughly clean all the crevices.

TIPS ON INGREDIENTS
Juicer damage due to owner negligence or from not following the instructions in the owner’s manual will void the warranty service.
DO NOT put the following ingredients into the juicer:

Hard seeds

Peach, nectarines, apricot, plum, mango, etc.
Remove hard seeds from the ingredients before juicing.

Hard or inedible skins

Pineapple, melon, mango, orange, etc.
Peel the skins from the ingredients before juicing.

Frozen fruits or ice

Frozen strawberry, blueberry, raspberry, etc.
Completely thaw frozen fruits before juicing.
Do not use ice. This can cause liter compressional deformation.

Others

Coconut, sugarcane, whole grains, etc
Do not extract ingredients with no water content.
Experience the best quality juice by understanding each ingredient’s characteristics and knowing the optimal way of handling the ingredients.
The Slow Juicer is an innovative product that uses a patented slow­ speed masticating technology to efficiently extract the juice from ingredients. The juicer is designed to obtain the best result from ingredients with firm composition and  with high water content.
For best result, each ingredient should be prepared and extracted depending on its characteristics and properties.

INGREDIENTS PREPARATION

Before Operating:

• Before Operating: If the juicer is jammed, press the REV button and hold until it becomes dislodged.
  Repeat REV-O-SOFT/HARD as needed.

• Continue operating the juicer until all the ingredients in the juicing bowl are extracted. Open the smart cap when juicing.

• Every ingredient yields different amounts of juice.

Juice Yield:

• For the optimal extraction and maximum juice yield, cut the ingredients following the guidelines given in this section.
• Insert ingredients slowly monitoring how the ingredients are extracted. The juice yield may vary depending on the juicing speed.

Soft fruits and vegetables (e.g. oranges, tomatoes):

• Peel the skin off oranges, and for tomatoes and apples, take out the stem.
• If the ingredients are larger than the feeding tube, cut the ingredients into pieces that will fit into the feeding tube.
• Fruits with seeds must be pitted before extraction.
  Cut to 1-4 wedges then slowly insert the ingredients down the feeding tube.

PREPARATION TIPS:

• Cut 1-4 wedges.

EXTRACTION TIPS:

• Slowly insert the ingredients one piece at a time.
• Use the pusher to push the ingredients down the feeding tube. (The pusher also helps prevent juice from spraying out of the feeding tube when extracting ingredients with high water content)
• It is recommended that the extracted juice be consumed within 48 hours after extracting. Depending on the density of the ingredients the extracted juice can gradually show layers over time.
• When an ingredient is being masticated by the juicing screw, the squeezed ingredient may splash juice through the feeding tube. Use the pusher to block out the juice splash when juicing.

How to Use the Smart Cap:

• Juicing with the smart cap open allows mixed juice creations with different fruits, vegetables and liquids.
• After juicing, close the smart cap to block excess juice from dripping, especially when disassembling the juicing bowl off the body.
• Leave the smart cap open when juicing ingredients that create excessive foam during extraction (e.g. apples, celery).
• Pay close attention when operating the juicer with the smart cap closed.
• Juice may overflow if the juice collected in the juicing bowl exceeds its capacity marked on the juicing bowl.

Hard fruits and vegetables (e.g. carrots, potato, beets & spinach):

PREPARATION TIPS:

• Slice the ingredients.
• Soak hard ingredient like carrots and ginger in cold water prior to juicing.

EXTRACTION TIPS:
Slowly insert the ingredients one at a time.
Pace the juicing speed ensuring each ingredient is thoroughly extracted.
To maximize the juice yield, juice with ingredients with high water content.
Ingredients with small seeds (e.g. raspberry, pomegranate, grape):
Slowly insert ingredients with small seeds to prevent the seeds from dogging the strainer.

PREPARATION TIPS:

• When juicing frozen ingredients(e.g. raspberry, strawberry), make sure they are completely thawed.
• Thoroughly rinse ingredients like grapes. Take the grapes off and discard the stem.
  For pomegranate, discard the skin and juice only the inner part.

EXTRACTION TIPS:
Depending on the size of the grape, insert several grapes at a time while monitoring the extraction result.

• Thaw frozen ingredients like pomegranate and raspberry then insert about 1 tablespoon (Sg) at a time.
• Frozen ingredients usually lose significant amount of fluid from thawing. When juicing, mix milk or yogurt to balance the fluid lost.

Caution

If you have any food allergies, be sure to choose ingredients that are safe and healthy for you.
Do not use any frozen ingredients with this product.
Only insert frozen food items into the juicer after they are adequately defrosted.
Fibrous and/ or tough leafy ingredients (e.g. celery, kale, pineapple):
Fibrous ingredients like celery and kale should be cut into small lengths before juicing.

PREPARATION TIPS

• Soak fibrous ingredients in cold water for about 30 minutes before cutting them.
• Separate each stem. Cut the outer stems that are thick and tough to 4 inches long or less.

EXTRACTION TIPS:

• One at a time, slowly insert the prepared ingredients.
• Insert more ingredients after the previously inserted ingredients have been completely extracted.
  1. Roll leaves in spiral as inserting into the juicer.
  2. Insert the leafy part of the ingredients first then alternate between leafy parts and stems.
  3. For ingredients like wheatgrass, grab a handful and insert in a bundle.

Caution

• The fibers from tough ingredients like celery can wrap around the juicing screw and affect juicer’s performance. Cut the stems that are thick and tough to 4 inches long or less.
• For ingredients like pineapple, slice off the rind of the pineapple and cut around the fibrous core. Cut the flesh of the pineapple to smaller pieces.
• Recommended amount of juicing per session is 1000g. When juicing more than1000g, wash the juicing body before continue juicing!

HOW TO DISASSEMBLE AND CLEAN

1. Switch O and unplug the power cord from the wall outlet.
   Note
   • Extract all the remaining pulp in the juicing bowl before stopping the juicer.
   • For easier clean up, operate the juicer for an additional 30 seconds after the juice is extracted.
   • When the juicer body is stuck, press the REV-0-SOFT/HARD button in this or derswitching back and forth 2 to 3 times to dislodge.

2. Press and hold the disassembly button on the side of the motor body and start rotating the Main Juicing Body anticlockwise to remove it from the socket of the juicer machine. The accessories cannot be removed if the button is not  pressed.
   Note
   • When moving the appliance, do not lift by grabbing the feeding tube. Always lift the appliance by grabbing the body or handle.

3. Twist the End Cap anticlockwise until the triangle alignment mark is aligned to unlock.
   Note
   • CAUTION: Do not use force to twist the End cap off. If it does not unlock easily, allow it to cool down before attempting again to ensure both parts are not damaged or cracked due to force.

4. Remove the Filter/ Strainer and the Auger/Spiral from the Main Juicing Body.

HOW TO CLEAN PARTS

Tip

• Before cleaning, ensure that the juicer is switched off and disconnected from the power supply.
• Detach and separate the accessories of the juicer.
• Empty the pulp and juice containers! (juice can be kept fresh for up to 72 hours).

Clean all detachable accessories as soon as possible after juicing to prevent residue and remaining pulp from drying. If any pulp residue does build up on any parts of the accessories, soak these parts in warm water for 30 minutes and  allow the residue to soften of make it easier to remove.
Do not sterilize any parts with hot water at a temperature higher than 80C or microwave to prevent parts from being heated, deformed, or damaged.

Note

• Rinse all the accessories and containers under running water and clean them with warm soapy water.
• To prevent rusting of accessories or parts getting clogged, please disassemble and rinse the accessories thoroughly immediately after use, and let dry completely before assembling them again!
• Do not use metal sponges to clean, as it will cause damage to the accessories and machine.
  Always clean the Auger/ Spiral with warm, soapy water and a soft cloth.

To better clean the Filter, use a cleaning brush every time to prevent leftover traces of fruits and vegetables residue from building up and clogging the holes

Storing the juicer
Store the juicer in a safe, dry place where its parts will not be damaged. When moving the juicer, you can hold it by handle.

TROUBLESHOOTING Q&A

■ When parts are difficult to disassemble

• After you have finished juicing, continue to run the juicer for an additional 10 seconds to ensure that all food has been properly processed and is not stuck any where in the Auger/ Spiral and

• Filter/ Strainer.
  Allow the juicer to cool down after an extended period of use before disassembling the End cap/ Squeezer from the Main Juicing Body. The End cap/ Squeezer should twist off from the Main Juicing Body once the triangle alignment has been set to unlock.

• CAUTION: Do not use excessive force to remove the End cap/ Squeezer from the Main Juicing Body to avoid damaging the product or its parts,

■ Juicer turned off in the middle of juicing

• Our juicer also has a self-protection function, If the working time exceeds 20 minutes, it will automatically shut down to protect the motor from overheating. Remember to allow the juicer to cool off before attempting to use it again,

■ Juicer is stuck and is not operating
If the juicer is stuck and not operating properly, try the following steps!

• Turn the power switch to “O” position.
• Pull out the power plug
• Plug in the power supply again after waiting for a few minutes
• Turn the power switch to “REV” position and hold it for a few seconds
• Try operating again
  If this reverse function is not working, please contact our customer service so that we can

■ Accessories are stained, damaged, or rusted

• Our accessories are made of high-quality and food-grade materials. However, citrus fruits and vegetables such as carrots (with strong carotene) contain acids and strong coloring that may stick to the surface of our accessories, which is why they may be difficult to clean over time.

• To prevent this, you should avoid squeezing large amounts of acidic fruits at one time, Remember to always soak and/ or wash immediately after use.

• For carrots and other hard vegetables or fruits, cut them into small pieces before putting them into the juicer.
  In this way, you can extract more juice and prevent food from being too hard, which can cause damage to the juicer accessories and shorten the juicer’s service life.

• To prevent rusting of accessories or parts from getting stuck, you need to disassemble (there is a separate section dedicated to helping you through disassembling the product) and rinse them thoroughly immediately after use and let them dry completely before assembling them again.

■ Juice leaks between the main juicing body and motor body

• Check to ensure that the silicone outlet where the metal lever of the Auger/ Spiral is inserted has not been damaged and is installed correctly.

■ Vibration or unusual noise during juicing

• The juicer and attachments may wobble due to vibrations by the motor base or the hardness/ toughness of the ingredients. This is not a malfunction but a normal part of the Auger/ Spiral’ s extraction process.
• Noise or sound may occur naturally when juicing certain ingredients such as apples ( due to apple skin), carrots, celery, or beets.

PARTS BREAKDOWN

Model ZM1525

ELECTRICAL WIRING DIAGRAM

120V 60Hz

WARRANTY REGISTRATION

Limited warranty for Vivid moo
Vividmoo’s limited warranty obligations are confined to the terms set below. Vivid moo warrants this Vivid moo slow juicer against defects in materials and workmanship for a period of one year from the date of the original retail purchase. This limited warranty is valid only in the country in which the product is purchased and comes with the product at no extra charge. However, shipping and processing fees will be incurred for returns, replacements, and refunds.
If a defect exists, and Vivid moo is obligated under this limited warranty, at its option, Vivid moo will (1) repair the product at no charge, using new or refurbished replacement parts, (2)exchange the product with a product that is new or  has been manufactured from new or serviceable used parts and is at least functionally equivalent to the original product, or (3) refund the purchase price of the product. A replacement product assumes the remaining warranty of the original product.

Obtaining warranty service
For limited warranty service, simply contact us via our customer service email at [email protected]. When you contact our customer service, you will be asked to provide your name, delivery address, telephone number, proof of  purchase (receipt) containing the order ID, description of the product, and purchase date.
Exclusions and limitations
This Vividmoo’s slow juicer limited warranty applies only to Vivid moo products distributed by Vividmoo’s under the Vivid moo trademark and does not cover purchases outside the Vivid moo website like Vivid moo unofficial Store, or  through authorized or unauthorized resellers.
Vividmoo’s is not connected to any sellers on eBay and therefore is not able to speak on their behalf or identify the seller for contact. Our Vivid moo customer service team at [email protected] only covers after-sales service for  products distributed by Vivid moo. For purchases on another website or platform, you may need to contact their customer service team.
We strongly advise against purchasing from any other unauthorized third-party sources as you may put yourself at risk of the following: Exclusions and limitations.

• Purchasing imitation or damaged products
• Not receiving the products you purchased
• Receiving products that cannot be returned
• Paying more for your products due to shipping fees, customs duties, and other taxes
• Receiving poor or no instructions on the proper use of the product purchased
• Voiding of warranty on products purchased from unauthorized resellers

Normal wear and tear are not covered by this limited warranty.
This limited warranty applies to consumer use only and is void when the product is used in a commercial or institutional setting.
This limited warranty extends only to the original consumer purchaser and is not transferable. In addition, proof of purchase must be demonstrated.
Replacement of the product or accessories (or if replacement is not feasible, a refund of the purchase price) is the exclusive remedy of the consumer under this limited warranty. Vivid moo shall not be liable for any incidental or consequential damages for breach of this limited warranty or any implied warranty on this product.
Vivid moo is not liable for any damage to products not covered by this warranty (e.g. pulp residue container, juice measuring container, cleaning brush, wrench, pushing rod, user guide, and juicing recipes).
This limited warranty does not cover:
(1) damage caused by accident, abuse, misuse, or misapplication; (2) damage caused by improper maintenance (including unauthorized accessories parts used); (3) product or a part that has been modified in any way;
(4) product has been used with an adapter/ converted and/ or (5) product that has been used for commercial or industrial purposes.
Thank you for purchasing a VIVIDMOO product. To register your warranty for this product, complete the information below, tear off the card at the perforation and then send to us. You can also register online by visiting: https://vividmoo.com/warranty-registration/

Email us at [email protected], to register warranty and get 2 years extended warranty on cold press juicer.

or email to: [email protected]

Thank you for choosing VIVIDMOO I Merci d’avoir choice VIVIDMOO I Gracias porelegir VIVIDMOO

****www.vividmoo.com
[email protected]

Read User Manual Online (PDF format)

Download This Manual (PDF format)

Download this manual  >>