SHGUMITE 318 7 Inch Digital Microscope Instruction Manual

SHGUMITE 318 7 Inch Digital Microscope

PRODUCT DESCRIPTION

Thank you for purchasing this equipment, it is complex to use, so please read this manual in detail to understand how to operate the microscope before using it.

IMPORTANT NOTES

1. Please fully charge the product before first use. Please do not charge directly through the PC, but choose a 5V-2A adapter.
2. This product is not a biological microscope and is not suitable for cell biology research.
3. The best focal length of the microscope is 30-90mm, you need to adjust the focal length through the focal length adjustment roller to achieve the clearest state.
4. This device cannot accurately read microscope magnification, it is a combination of digital and optical magnification microscope, and the specific magnification effect is subject to the actual picture taken.
5. When the battery is low, both the storage mode and PC camera mode cannot be used normally. This is not a product failure.
6. Do not touch the lens or other optical parts with your hands, otherwise, it will cause image blur and affect imaging quality.
7. Do not disassemble the product or component structure by yourself to avoid abnormal equipment use.

BATTERY INSTRUCTIONS

1. Please use a safe and compliant 5V/2A home charger to charge this device.
2. This device supports charging while in use.
3. If the device is left unused for a long period of time, please ensure that it is charged at least once every 3 months to prevent irreparable damage caused by over-discharging the battery.

FUNCTION INTRODUCTION

1. Power button
   • Press and hold for 3 seconds to switch on/off the device
2. Menu key
   • Set the relevant parameters
3. Left selection key
   • Scroll up / switch between different color display modes
4. OK key
   • Confirm selection/screen flip
5. Right selection key
   • Scroll down / switch between different colour display modes
6. Mode switch key
   • Switch between the three function modes
7. Photo key
   • Short press to take a photo / start recording/ end recording
8. Light adjustment key
   • To adjust light
9. External light source power supply port
   • Output 5V = 1A
10. Charging port
    • Input 5V – 2A
11. Charging indicator
    • When charging the red light is on, when it’s done the green light is on
12. TF card slot
    • Support expansion 0-128G TF (Micro SD) card
13. Reset button
    • When the product is dead, press to restart the device

WORKBENCH INTRODUCTION

PRODUCT SPECIFICATIONS

STEPS TO USE

1. After opening the package, put the 3 base plates together as shown in the picture below.
2. Combine the bracket bars and the base plates together with screws as shown in the picture below
3. Attach the main unit to the bracket as shown in the picture below.
4. Before using this device, you need to insert the TF card.
   • Insert the TF card
   • Please insert the TF card when the power is off.
   • Please be careful not to mix the insertion direction and the front and back of the TF card.
   • Do not use excessive force when inserting or pulling out the TF card, otherwise, the structure of the card slot may be damaged.
5. After fixing the workstation, press and hold the power switch button for 3 seconds to turn on the device and start working.
6. Move the lens up and down by adjusting the bracket to match the adjustment of the focus barrel to obtain the required magnification for observation.
   • When the lens is adjusted downwards, the corresponding focusing barrel needs to be rotated to the right, and the magnification increases.
   • When the lens is adjusted upwards, the corresponding focusing barrel needs to be rotated to the left, decreasing the magnification.

FUNCTION BUTTON

1. After switching on, the product is in photo mode by default, click the key to take photos, click the key once to enter the camera mode, click to start recording, and then click to end the recording, click once again to enter the file browsing mode.
   • The key is set to: “Photographic mode ” – “ Video mode ” – “ File browsing mode”, with three modes circulating.
2. In “Photography mode”, click the key to switch between different color modes.
3. In “Photography mode “, click the “OK” key to rotate the image.
4. In click the key to adjust the photo-related parameters, click and again to enter the settings page.

File browsing” mode operation instructions

1. Click twice to enter the file browsing mode, and you can view all the saved photos and videos. If you need to delete the current photo or video file, click the key to enter the delete page.
2. If the current file is in video format, click the keys for the play/pause function, and click the left and right keys for the fast forward and fast rewind function.

Setting page” operation instructions

1.  Double-click the key to enter the settings page.
2. Click ” ” “ to select the required menu item.
3. Select the required item, click the “ OK” key to enter, select the desired parameters, and then click the “OK” key to confirm.
4. When finished setting, double-click the key to exit the setting mode.
5. The first time you use the device, you need to go to select the required language (the factory setting of the device is: English).

MODE INTRODUCTION

The product has three mode functions, which are as follows:

1. Memory mode: connect to PC, read, write, and format TF card.

2. PC camera mode : Connect to a computer and use it through computer software, making the large screen more intuitive.

3. Normal mode: normal use mode of the device.

4. Memory mode:
   Connect the microscope to the computer via USB data cable, select memory mode, and then click the OK button to view saved photos and videos on the computer.

5. PC camera mode:
   Note: When using PC mode,

6. some function keys will not be available, only the light adjustment keys can be used.

7. In PC camera mode, it is normal that the device monitor will not display images.

8. When connected, if the software has no image, please repeat plugging and unplugging the TYPE-C data cable or replace the cable.

Windows system:
Support Windows vista/7/8/10/11 or higher.
Software Installation

1. For WIN 7/8 systems, download and install the “AMCAP” software.
2. For WIN 10/11 systems, search directly for the software “Windows Camera” (Note: Please disable the default laptop camera in Windows! And you must change the camera’s privacy settings, which is needed to allow access.
3. Or download the application “Smart Camera” for your computer, download link: www.inskam.com/download/camera.zip
4. Connect your microscope to the USB port on the back of your computer case with the Type-C cable that comes with the microscope, press and hold the power button to turn on your computer, select enter PC camera mode, and open the computer software to use.
   Different Windows systems are recommended to use different software, please choose to download the corresponding software to use according to the system.

the software page display:

1. Software “AMCAP” page, as follows.
2. Windows Camera” page, as follows.
3. Software “Smart Camera” page, as follows.

Note: If the following situation occurs for a long time during the process of connecting the device to the computer using the data cable. You can try the following solutions:
a. Firstly, please plug and unplug the Type-C cable repeatedly or plug the data cable into the USB port at the back of the computer case to ensure that the device is powered properly.
b. Secondly, the software may not be compatible with the system, you can check if you are using the software installation instructions correctly.

MacOS: MacOS X 11.0 or higher, not available for Apple laptops with Type-C interface.

1. Open the software (we recommend using the Photo Booth software that comes with your Apple computer).
2. Firstly, go to the “Applications” directory in the Finder window and find a application called “Photo Booth”.

Connecting the device

1. Connect the microscope to your computer’s USB port with the Type-C connector that comes with the microscope, press and hold the power button to turn on the device, and choose to enter PC camera mode. Open and run “Photo Booth”
2. click Photo Booth and select the camera “USB CAMERA”.
3. You can also use the alternative software “Quick Time Player”.

COPYING PICTURE AND VIDEO FILES

You a computer card reader to copy directly or use a Type-C cable to copy

If the device is not connected to the computer when copying, please restart the device or plug in the Type-C cable. Do not plug or unplug the Type-C cable during data transfer, as this may cause data transfer failure.

CHARGING GUIDE

• Note: Please use a 5V-2A adapter to charge your device.
• Connect the device to the Type-C / USB adapter for charging (5V = 2A), fast charging is not supported.
• During charging, the indicator shows a red light.
• When the device is fully charged, the indicator shows a green light.
• When the battery is low, both memory mode and PC camera mode cannot be used normally, and the battery must be charged beyond the 1/3 position before it can be used again.

FAQ Help

1. The product cannot be switched on.
   • Confirm whether the product has power.
   • Confirm whether the power is connected.
   • Confirm that the power supply is not sufficient due to the computer being used for charging.
2. The product is dead.
   • Press the device reset button and restart the device.
3. The image is not clear.
   • Whether the object being measured is correctly positioned directly below the lens.
   • Whether the focal length adjusted to the optimum position?
   • Whether the light is used correctly?
4. Product charging.
   • Please use a 5V-2A adapter to charge the device, fast charging is not supported.
5. TF card cannot be recognized.
   • Please check if the TF format is FTA32 format, if not, please format it; if not recognized, please re-plug the TF card.
   • The device supports a Class 10 high-speed memory card, not a Class 4 low-speed memory card.
6. When using PC camera mode, the software does not show the picture after connecting to the computer.
   • Reconnect the product to the computer.
   • Check if you clicked into PC mode.
   • Whether the battery is low.
   • Make sure that you are using the correct data cable and that you are not using a charging cable without a data transfer function.

FCC Statement

Any changes or modifications not expressly approved by the party responsible for compliance may void the user’s authority to operate the equipment.
This equipment complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This equipment will not cause harmful interference
2. This equipment must accept any interference received, including interference that may cause unintended operation.

FCC Radiation Exposure Statement:
This equipment complies with the FCC radiation exposure limits established for uncontrolled environments.

WEEE Compliance

• Proper disposal of this product (Waste Electrical and Electronic Equipment) (for countries with independent collection systems)
• This marking on the product, accessories, or literature indicates that the product and its electronic accessories should not be disposed of with other household waste at the end of their useful life.
• To prevent uncontrolled waste disposal that may be hazardous to the environment or human health, please separate these items from other types of waste and recycle them responsibly to promote the sustainable reuse of material resources.
• Household users should contact the retailer or local government office where they purchased this product for details of where they can take these items and how to recycle them in an environmentally friendly manner.
• Business users should contact their suppliers and check the terms and conditions of their purchase contracts.
• This product and its electronic accessories should not be mixed with other commercial waste for disposal.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>