STP3005DH DC Power Supply Variable User Manual

: June 14, 2024
: STP

Table of Contents

For Safety Use
Know The Device
Technical Specifications
Operation Instruction
Frequently Asked Question (FAQ)
About Us
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Regulated DC Power Supply
Green Power Series
User Manual Shenzhen SKY TOPPOWER Technology Co., Ltd

For Safety Use

Please follow the tips below when operating this unit.

The device Is intended for indoor use only.
Do not open or repair the device. That will void the warranty.
Do not use the device in a damp environment
Keep the device away from heat or water, magnetic field.
Keep the device and all loose parts (if any) away from children, pets and unauthoried persons.
Don’t sharply bend, cut, stretch, knot, or step on the cord. Don’t disconnect by pulling on the power cord, rather grab the plug.

Know The Device

SKY TOPPOWER lab-type regulated power supply is a simple, accurate Constant Current (CC), Constant Voltage (CV) DC power source that provides the displayed power and current up to the listed ratings. It can be used to power equipment during testing or during repair and maintenance, or for calibration stations. It will power DIY projects on your work bench at home or for electronic and telecommunication classes at educational Institutions.

Technical Specifications

Model	PS305H	PS3010H

Operation Instruction

Step 1. Presetting Constant Current Value.
a. Turn on the power supply, and adjust the output voltage to about 3V by turning the coarse &/or fine Voltage knobs.
b. Turn off the device.
c. Short the positive °+”and negative “-” terminals using the leads. Then turn on the power supply. and remove the test lead.
d. Adjust the current to the desired amps by turning the coarse or fine Current knobs.
Please do not adjust the Current knobs once the current limit has been set as above. Current limiting has now been set for the whole range of output voltages.
Step 2. Presetting Constant Voltage Value.
a. Adjust the output voltage by turning the coarse or fine Voltage knobs.
b. Turn off the device.
Please do not adjust the voltage knobs once the voltage has been set as above.
Step 3. Now connect your load: positive to positive and negative to negative.
Note: If the display shows (CC), either your preset current limiting value is too low or your load requires more voltage or current. You need to adjust your current and voltage settings using the above steps.
About CC &CV
The power supply functions as a constant vollagefsource (CV) as long as the load current is less than the preset “urrent limiting value. If the load current becomes equal to or greater than the preset currant limit, the power supply will automatically cross over to the constant current mode and the voltage will drop. (CC} will display on the LED panel indicating the supply is now operating as a constant current source.
If the load current drops below the preset current limit, the power supply retums to constant voltage( CV) mode.

Frequently Asked Question (FAQ)

1. Q: When | power it on, the current displays show zero, is it normal?

A: If itisn't connected to a load it should read zero because no current is flowing. This DC power supply requires manual current and voltage settings.

2. Q; How do | get it to stay in constant current mode?

A: CC is attained when the rated set current is exceeded. It would stay in that mode till the current drops back to the preset.

3. Q:How to set the current value without load connecting?

A: Please short the +/- outputs together, set the current, and remove shorting cable. You could also refer to the operation instruction.

4.Q: Does it remember the last settings when turned off and back on again?

A: Yes, because it's on a dial. If you don't adjust it and just flip the on and off switch in the front it will remain the same.

5. Q:How to switch between Constant Voltage (CV) and Constant Current (CC)?

A:The supply will do it automatically. Turn the current down or up to adjust the limit. When the mode CC shifts to CV, the CV indicator light turns on. You can adjust it to any value. It automatically switches to CC when the set current value is exceeded.

About Us

SKY TOPPOWER is a leading manufacturer for various OC regulated power supply in Shenzhen China. As an integrated high-tech enterprise including design, development, production, sales and services, OEM & ODM are welcome.
SKY TOPPOWER’s products comply with RoHS, CE and FCC certificates.Our professional team has over 10 years of expertence in design, manufacturing, selling of DC power supply, We are passionately committed to bring alternate power solutions to the customers that makes their DIY project smooth and efficient. We bring our products to market domestically across over 20 provinces in China, as well as intemationally market such as Europe. North America , Austria, Asia and so on.
With perfect quality, enthusiastic services. timely supply, thoughtful pre- eale after-cales services provided, we cooperate with customers all over the world , and win a good reputation among customers. Please contact SKY TOPPOWER team below ways for warranty service or support needed:
Tel: +86-755-2304 7771
Skype: live:skytoppower_2
E-mail: stp@skytoppower.com
Web: www.skytoppower.com
Add: 3/F, A2 Building Baical industrial Park No.19, Tlanbao Road, Yingrenshi Shiyan Street, Baoan District, Shenzhen, China 518055
Pleaee visit website: hittp://u6.gg/k37wq or search for “SKY TOPPOWER™ fo visit more videos of our deivece in YouTube.