Adalov CPE365 Gigabit Wireless Bridge User Manual

WIRELESS BRIDGE
USER MANUAL

CPE365 Gigabit Wireless Bridge

Model:CPE365
Tips:
Thank you for ordering and using AdaLov CPE365 Wireless Bridge, please read the manual carefully before use.If there are any problems during the use, please contact us in time.
Customer Service Email: cs@adalovus.com

Chapter 1- Get to Know About Your Wireless Bridge

1.1 Product Overview

1.2 Appearance
1.2.1 Port and Button Description

master bridge(transmitter),and pushing the button to “B” indicates that the bridge acts as the slave bridge (receiver)
Reset Button| Short press once to toggle a different character to pairing; Press and hold for 10s to reset the wireless bridge
LAN 1 Port| The 100Mbps adaptive RJ45 port,also can be used as a POE port
LAN 2 Port| The 1000Mbps adaptive RJ45 port,also can be used as a POE port
Digital Tube| Know the current configuration character through the digital tube
DC| 12V/1A

1.2.2 LED Explanation

stronger signal, the more lights on; In the slave bridge mode:it indicates the signal strength of the connection after successful pairing, the stronger the signal, the more lights.
LAN1/LAN2| The green light is solid when the LAN1/LAN2 Port is connected and goes out when the LAN1/LAN2 Port is disconnected.
LED Display| Display current number, including 0, 1, 2, 3, 4, 5, 6, 7, 8, 9, A, b, C, d, E, F loop.

1.3 Specifications

11n: 7.2M, 14.4M, 21.7M, 28.9M, 43.3M, 57.8M, 65M, 72.2M,14.4M, 28.9M, 43.3M, 57.8M, 86.7M, 115.6M, 130M, 144.4Mbps 433Mbps
Transfer method| Direct Sequence Spread Spectrum (DSSS)
Modulation| OFDM/ BPSK/ QPSK/ CCK/ DQPSK/ DBPSK
Protocol standard| IEEE802.11ac, IEEE802.11n, IEEE802.11a, IEEE802.3u
Agreement| CSMA/CA, TCP/IP, IPX/SPX, Net BEUI, DHCP, NDIS3, NDIS4, NDIS5
Frequency range| 4900 ∼6100MHz
Power| ≤3W, POE24V∼1A
Antenna| 16dBi, HorizontaI60°/ Vertical30°
WEPGUI| Support
Telnet| Support
Serial| Support
Safety| WEP64/128bits,WPA,WPA2,802.1x
One Bridge Item size / Weight| 24.5 x 9 x 4.8cm/ 295g (Two wireless bridges included)

Chapter 2 – Highlights

1. Using 5.8Ghz wireless technology;
2. Gigabit wireless bridge with 1000Mbps RJ45 LAN port;
3. Built-in 16dbi high gain directional WiFi antenna;
4. IEEE802.11ac IEEE802.11n, IEEE802.11a, IEEE802.3u;
5. Transmission distance up to 3km(direct line-of-sight);
6. Master bridge supports WiFi hotspot access;
7. Dialing pair, one key operation;
8. WDS networking mode;
9. Support point-to-point(PTP), point-to-multipoint mode(PTMP);
10. Dynamic MIMO power saving mode(DMPS) and APSD;
11. Support 24V POE power supply, easy to install and deploy;
12. Support WEB GUI access.

Chapter 3 – Package

Package Included:
2 x CPE365 Wireless Bridges,
2 x POE Adapters,
2 x Metal Cable Ties,
2 x Network Cables,
1 x User Manual.

Chapter 4 – Wireless Bridge Pairing & Installation

4.1 POE Power Supplyower Supply
The CPE365 wireless bridge adopts a POE power supply, which is easy to Install and manage while saving costs.

1. According to the requirements, prepare along enough network cable (Recommended within 20 meters, must Cat 5e network cable to connect the wireless bridge and the POE power supply. The POE port of the POE power supply is connected to the LAN port to the wireless bridge.
2. The LAN port of the POE power supply is connected to the PC, router, and switch.

4.2 Master Bridge & Slave Bridge Pairing
The bridges are pre-paired, just connect to POE adapter, it will auto pair in a few minutes, you can adjust the channel.

1. Set master/slave bridge:
   Set master bridge–(switch “A-B” button to “A” position) Set slave bridge– (switch “A-B” button to “B” position)
   Please refer below diagram:

2. Short press the reset button to change the channel from 0-9, A-F, the LED indicator will display the numeric to show what channel it is, please keep the master and slaves bridges in the same channel.

3. Wait them for pairing. When the signal light on the side turns on, it means the pairing is successful;

4.3 Master Bridge & Slave Bridge Installation
4.3.1 Install Wireless Bridge Diagram

4.3.2 Installation Steps:

1. Put the bridges front side face to face in the same direction, then use the ties to fix the CPE.
   (Note: The bracket is not included in the package).

2. Use a long network cable to connect the POE adapter and the bridge.

3. Master bridge connection:
   Step 1: The LAN port of the POE Adapter connect to the router or the internet through an Ethernet cable.
   Step 2: The POE port of the POE adapter connect to POE/LAN port of the master wireless bridge by another Ethernet cable.

4. Slave Bridge (or slaves bridges) Connection: Step 1: The POE port of the POE adapter connect to the POE/LAN port of slave bridge through an Ethernet cable
   Step 2: The LAN port of the POE adapter connect to the LAN port of the computer or router by another Ethernet cable

5. Tips:
   (1). Before installation, please check whether the wireless bridge is paired well, please refer the master and slave pair setting page.
   (2). For installation, keep clear line of sight between the 2 wireless bridge. There is no strong electricity, strong magnetism, and other signal interference between the two wireless bridges.
   (3). The signal transmission angle of the wireless bridge is 60°, for point- to-multipoint installation, the angle of the slave bridge needs to be adjusted to ensure that it is within the 60° signal range of the main bridge. The antenna polarization direction is horizontal 60°/ vertical 30°.

6.  Point-to-Point Diagram

7.  Point to Multipoint Diagram(Up to 8 slave bridges)
   Note:There is only one Master bridge,and others all Slave bridges.

Note:

1.  The slave bridges must in the front of the master bridge;
2. The master bridge and slave bridges must be face to face;
3. The maximum angle between the master bridge and slave bridges should not exceed 60 degrees.

Chapter 5 – Application

5.1 Point to Point for Network Extend Diagram:

5.2 Point to Point for Video Transmission Diagram:

5.3 Multiple Network Equipment Expansion Diagram:

5.4 Point to Multi-Point Connection Diagram:

5.5 Multiples Clients Connection Diagram:

5.6 Relay Mode Connection Diagram:

Chapter 6 – Computer Access

6.1 Modify Computer’s IP

Refer to the figure left to connect the CPE to the computer through a POE adapter and an Ethernet cable.
Note: You can enable the device without advanced settings
2. Modify your computer’s IP address, make your computer’s IP a bridge’s IP address be on the same network segment(LAN), so that you can access them.
Click the network icon in the lower right corner of the computer, then click “Network & Internet settings”

Select Ethernet and click “Change Adapter Options”

Find the network connection you are using, right click it and select “Properties”

Double-click the “Internet Protocol version 4(TCP/IPv4)” go to IP configure interface

Configure your computer IP address as 192.168.255.x (x is a figure 0-200).
Note: The Pc’s IP can not be the same as the bridge.
6.2 Login via browser
Open the browser and enter the IP address of the wireless bridge to access, for example, enter “192.168.255.101″ on the browser address column, you can access your bridge control panel.

A login screen will appear, by default, the Username and Password of the wireless bridge all are “admin”. Note:
“admin” is not the password of the WiFi SSID, it is just the password for WEB access

Digital & IP Chart

Digital &
IP Chart| A – IP| B – IP| 5.8G ID| WiFi SSID| Password
---|---|---|---|---|---
0| 192.168.255.100| 192.168.255.200| 0| CPE5G 5G0| zIlinkcpe1234560
1| 192.168.255.101| 192.168.255.201| 36| CPE5G 5G36| zIlinkcpe12345636
2| 192.168.255.102| 192.168.255.202| 40| CPE5G 5G40| zIlinkcpe12345640
3| 192.168.255.103| 192.168.255.203| 44| CPE5G 5G44| zIlinkcpe12345644
4| 192.168.255.104| 192.168.255.204| 48| CPE5G 5G48| zIlinkcpe12345648
5| 192.168.255.105| 192.168.255.205| 120| CPE5G 5G120| zIlinkcpe123456120
6| 192.168.255.106| 192.168.255.206| 124| CPE5G 5G124| zIlinkcpe123456124
7| 192.168.255.107| 192.168.255.207| 128| CPE5G 5G128| zIlinkcpe123456128
8| 192.168.255.108| 192.168.255.208| 132| CPE5G 5G132| zIlinkcpe123456132
9| 192.168.255.109| 192.168.255.209| 136| CPE5G 5G136| zIlinkcpe123456136
A| 192.168.255.110| 192.168.255.210| 140| CPE5G 5G140| zIlinkcpe123456140
b| 192.168.255.111| 192.168.255.211| 149| CPE5G 5G149| zIlinkcpe123456149
C| 192.168.255.112| 192.168.255.212| 153| CPE5G 5G153| zIlinkcpe123456153
d| 192.168.255.113| 192.168.255.213| 157| CPE5G 5G157| zIlinkcpe123456157
E| 192.168.255.114| 192.168.255.214| 161| CPE5G 5G161| zIlinkcpe123456161
F| 192.168.255.115| 192.168.255.215| 165| CPE5G 5G165| zIlinkcpe123456165

Chapter 7- Advanced settings

Can turn on/ off “Hide SSID”, modify the SSID name and WiFi password, click “Apply” to complete the setting.Can modify the two bridge’s IP, click “Apply” to complete the setting.Can modify the two bridge’s Administrator Login name and Password, click “Apply” to complete the setting.

Chapter 8 – After-Sales Service

Tips:

1. The installation of this device requires network knowledge, if you can not install it, please contact us or ask a professional for help, if the product you receive is damaged or miss any accessories, please contact us for exchange or resend.
2. The wireless transmission maximum speed(wireless bridge A to B unit) is 900Mbps, the LAN network transmission maximum speed (POE adapter to wireless bridge connection) is 433Mbps, the LAN port is 100/1000Mbps standard.

Tech Service email: cs@adalovus.com
You can visit the installation video guide on :
https://www.youtube.com/watch?v=ZJ91i-9N2B0
Scan this code to watch video:

https://wx.hlcode.cn/?id=NK8iRFl

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>