NEWS HUD Speedmeter User Manual

NEWS HUD Speedmeter

Product Information

Specifications

• Power Supply: 5V
• Display Functions:
  • Satellite Icon
  • Vehicle Speed Display
  • Compass (N, E, W, S)
  • Speed Unit (KM/H or MPH)
• Wave Button Function
• Setting Menu with various functions

Product Usage Instructions

Entering Setting Mode
Long press the wave button to enter the setting mode. Use the right button to navigate the menu and short press the wave button to confirm selections. To exit setting mode, long press the wave button.

Speed Adjustment
Adjust the speed parameter value if there is a discrepancy between the HUD and dashboard readings. Follow the example provided in the manual for guidance.

Over Speed Alarm
Set the over speed alarm threshold to receive alerts when the vehicle speed exceeds the specified limit.

Fatigue Driving Alarm
Set the interval for fatigue driving alarms to ensure safe driving practices.

Brightness Adjustment
You can adjust the brightness level of the display manually from 1 (darkest) to 11 (brightest) or choose automatic sensitivity adjustment.

Factory Reset
To perform a factory reset, long press the wave button for 3 seconds. This action will revert settings to default values.

Troubleshooting

1. No Display and No Power: Check USB cable and power supply.
2. No Car Speed Display: Ensure satellite connection by driving to an open area.
3. Inaccurate Speed: Verify speed unit and adjust parameter value if needed.
4. Driving Direction Display Error: Direction display corrects after vehicle speed exceeds 5 KM/H.
5. Speed Displayed After Car Stops: Signal instability may cause drift in certain areas.
6. Turning Off the Buzzer: Press left for 2 seconds to silence the buzzer.

Instructions for Recycling and Disposal
Follow local regulations for recycling and disposal of electronic devices. Dispose of the product responsibly.

Frequently Asked Questions (FAQ)

• Q: What should I do if my display shows inaccurate speed readings?
  A: Check the speed unit setting and adjust the parameter value as needed according to the manual instructions.

• Q: How can I reset the device to factory settings?
  A: Long press the wave button for 3 seconds to perform a factory reset.

SPEEDOMETER – USER MANUAL

WARNING: This product operates on a 5V power supply. Do not use a voltage higher than 5V.

DISPLAY FUNCTIONS

1. Satellite Icon: When a satellite is found, the GPS light stops flashing and remains steady for normal use.
2. Vehicle Speed Display
3. Compass: Indicates directions N (North), E (East), W (West), S (South).
4. Speed Unit: Displays speed in KM/H (kilometers per hour) or MPH (miles per hour).

WAVE BUTTON FUNCTION

1. Left
2. Press In
3. Right
4. Wave Button

• Short press in: Confirm the option after entering the setting menu.
• Long press in: Enter the setting menu. After adjusting, press vertically for 2 seconds to save and exit.
• Push left: Move options after entering the setting menu.
• Long push left: Push left for 2 seconds to turn off the buzzer alarm. Repeat to turn it on.
• Push right: Switch between concise mode and standard mode. Move option after entering the setting menu.

ENTERING SETTING MODE : Long press in to enter the setting mode. Press right to choose the menu, and short press in to confirm. Once finished with the setting, long press in to exit.

TROUBLESHOOTING

1. No Display and No Power:
   Check if the USB cable is damaged. Replace the USB cable if necessary. Ensure the power supply does not exceed 5V.

2. No Car Speed Display:
   After powering on the HUD, the satellite icon will flash while searching for a satellite. Drive the car to an open road. The display will work once the icon stops flashing.

3. Inaccurate Speed:
   Check if the speed unit is correct (KM/H or MPH). Refer to the settings to switch the unit.
   Manufacturers often calibrate the dashboard speed 5-7% higher than the ECU. The international standard is based on satellite data. (If the dashboard shows 100 and the device shows 105, change the default value to 102).

4. Driving Direction Display Error:
   The direction will display correctly once the vehicle speed exceeds 5 KM/H.

5. Speed Displayed After Car Stops:
   In areas like underground parking lots, tunnels, or under overpasses, satellite signal may be unstable, causing drift.

6. Turning Off the Buzzer:
   Push left for 2 seconds to turn off the buzzer. Repeat to turn it back on.

INSTRUCTIONS FOR RECYCLING AND DISPOSAL:

This label means that the product cannot be disposed of as other household waste throughout the EU. To prevent potential damage to the environment or human health from uncontrolled waste disposal. Recycle responsibly to promote the sustainable use of material resources. If you want to return a used device, use the drop-off and collection system, or contact the retailer from whom you bought the product. The retailer can accept the product for environmentally safe recycling.
A declaration by the manufacturer that the product complies with the requirements of the applicable EU Directives.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>