amazon basics B087RJK3GW Hose Reek Air Hoses Instruction Manual

Instruction Manual

IMPORTANT SAFEGUARDS

Read these instructions carefully and retain them for future use. If this product is passed to a third party, then these instructions must be included.
When using the product, basic safety precautions should always be followed to reduce the risk of injury including the following:

WARNING
Risk of injury!

• The warnings, cautions and instructions mentioned in this user manual cannot cover all possible conditions or situations that might occur. It must be understood by the operator that common sense and caution are factors that cannot be built into this product, but must be considered by the operator.
• Wear impact-resistant eye protection that meets ANSI Spec. Z87.1 in work area at all times.
• Direct exposure to pressurized air could result in severe bodily injury. Even low pressure is very dangerous and can cause personal injury.

CAUTION
Risk of damage to swivel connector!
Use a flexible inlet hose only. Do not use solid or rigid piping.

• Keep the work area clean and dry. Damp or wet work areas can result in injury.
• Keep children away from work area. Do not allow children to handle this reel.
• Use the right tool for the job. Do not attempt to force small product to do the work of larger industrial product. There are certain applications for which this product was  designed. It will do the job better and more safely at the capacity for which it was intended. Do not modify this product, and do not use this product for a purpose for which it was not intended.
• Check for damaged parts. Before using this product, carefully check that it will operate properly and perform its intended function. Check for damaged parts and any other conditions that may affect the operation of this product. Replace damaged or worn parts immediately.
• Do not overreach. Keep proper footing and balance at all times to prevent tripping, falling, back injury, etc.
• Do not use the product when tired or under the influence of drugs, alcohol or medication. A moment of inattention while operating this product may result in serious personal injury.
• Ensure that the product is properly assembled and installed before connecting input and output hoses.
• Make sure the incoming line pressure does not exceed the rated operating pressure of the product.
• Bleed air pressure from system before servicing the product.
• Do not use hoses different from that for which the product is intended. See “Specifications” chapter.
• Mounting fasteners should be installed to maintain tightness under vibration and checked periodically to ensure tightness.
• Overhead installation should be such that the product is not supported by bolts in tension only. A safety chain, cable, enclosure or netting is strongly recommended to minimize damage and/or possible injury in the event of a mounting failure.

SAVE THESE INSTRUCTIONS

Intended Use

• The product is intended to connect to pneumatic tools. It is intended to deliver air pressure to a flexible size area in a workshop or on a job site.
• No liability will be accepted for damages resulting from improper use or non-compliance with these instructions.

Product Description

A. Hose reel
B. Handle
C. Mounting bracket
D. Sleeve
E. Reel flange| F. Male air inlet
G. Hose clamp with screw
H. Swivel female air outlet
I. Hose protective spring
J. Screw and nut x3
---|---

Before First Use

DANGER
Risk of suffocation!
Keep any packaging materials away from children—these materials are a potential source of danger, e.g. suffocation.

• Check the product for transport damages.
• Remove all the packing materials.
• Before connecting the product to the line pressure, check that the line pressure corresponds with the pressure details shown on the product rating label.

Setup

5.1 You Will Need

WARNING
Risk of electric shock!

• Before mounting, determine the suitable mounting location. The mounting surface must be capable of supporting the weight of the product.
• Install the product in premises conforming to current regulations and standards covering work environments.
• Do not drill into any pipes or power lines beneath the surface during mounting holes preparation. Use voltage/metal detector.

5.2 Installation Method

5.3 Handle installation

• Match the handle (B) to the three holes in the reel flange (E). Attach the handle to the reel flange using the provided screws and nuts (J). Make sure that the handle is mounted tightly and securely.

5.4 Hose assembly

1. Choose a proper air hose (not provided) you desire to use with the hose reel (A).

2. Loosen the hose clamp with the screw (G) (Fig. 1).

3. Feed the hose through the clamp (G) and the hole of the reel flange (E) (Fig. 2).

4. Attach the hose protective spring (I) to  the hose end.

5. Connect the male fitting of the hose end to the swivel hose connector (H).Use sealant tape (not provided) for an airtight connection (Fig. 3).

6. Tighten the hose clamp with the screw (G).

7. Wind the hose onto the sleeve (D) using the handle (B). Make sure that the hose is wound onto the reel drum evenly (Fig. 4).

8. Now the hose reel is ready for mounting (Fig. 5).

5.5 Hose reel mounting
NOTICE The hose reel can be mounted to a stable surface like a workbench, wall, floor, or ceiling with hardware (not provided).
The surface you mount to must be capable of holding the weight of the hose reel with a hose, and the additional stress from tugging on the unit with the hose being extended.
When the hose reel is mounted to a ceiling, it must be at least 10 ft (305 cm) above the floor.
If you pre-drill when mounting the hose reel, make sure not to drill a hole deeper or larger than the screws (not provided) you will use to mount the bottom base.
The size of the screws should be 13/32″ (10 mm) in diameter. The length of the screws should be 1-3/4″ (45 mm).
Mount the hose reel (A) to a suitable location on a workbench, wall, floor, or ceiling, etc. by fitting proper hardware (not provided) through four holes of the mounting bracket (C). Make sure that the hose reel is mounted tightly and securely.

Operation

WARNING
Always disconnect the product from the air source after air tool operation.
Always disconnect the air tool attached to the product from the air supply before making any adjustments and changing accessories.

NOTICE Follow all instructions from the compressor manufacturer when connecting the air supply to the product.
Follow all instructions from the air tool manufacturer when operating the air tool.

1. Connect the air supply to the male air inlet (F) of the hose reel (A) using a proper air hose and/or lead hose (not provided). Apply sealant tape on the male threads of the air fitting for an airtight connection.

2. Extend the air hose slowly to the desired length.

3. Attach the air tool to the air outlet of the air hose in the hose reel (A). Use sealant tape for an airtight connection (Fig. 6).

4. After using the hose reel (A), hold the handle (B), and rotate the sleeve (D) to rewind the air hose manually into the reel drum while holding the air hose with your hand. Make sure the air hose is rewound into the reel drum evenly.

Cleaning and maintenance

7.1 Cleaning

• To clean the product, wipe with a soft, slightly moist cloth.
• Never use corrosive detergents, wire brushes, abrasive scourers, metal or sharp utensils to clean the product.

7.2 Maintenance

• User servicing of the reel is limited tore placing input/output hoses only.
  Refer all other repairs to an authorized service centre. Failure to do so can result in personal injury and/or product damage.

• Check the components regularly to make sure all screws and bolts are tightened.

Troubleshooting

The product does not turn when
the air hose is being extended or rewound.| • The reel drum is locked.| • Check and make sure that the hose reel is free from any foreign particles and is in good working condition.
The product runs slowly or will not operate.| • Low air pressure.| • Adjust the air regulator to the correct working pressure for the tool.
| • The air pressure drops.| • Make sure that the air connection hose is of the proper size and length. Do not use a multiple number of hoses connected together with quick-connect fittings, which will result in pressure drops and reduce tool power.
| • The air hose leaks.| • Tighten and seal all NPT threads of hose fittings in your air line with thread sealant tape. Replace if the hose is damaged.

Disposal

Dispose of the product according to local regulations. If in doubt, consult your local authorities.

Feedback and Help

We would love to hear your feedback. To ensure we are providing the best customer experience possible, please consider writing a customer review.
Scan QR Code below with your phone camera or QR reader:

https://www.amazon.com/review/review-your- purchases/listing/?ref=HPB_UM_CR

If you need help with your Amazon Basics product, please use the website or number below.
amazon.com/gp/help/customer/contact-us

**amazon.com/AmazonBasics
Manual Hose Reel**
Fits 3/8-Inch (0.95 cm) by 50
Feet (15.24 m) Air Hoses (Not Included)
MADE IN CHINA
V02-06-23

References

• Amazon Basics

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>