OLIGHT RN120C Rechargeable Bike Rear Lights User Manual
- June 14, 2024
- OLIGHT
Table of Contents
OLIGHT RN120C Rechargeable Bike Rear Lights
Product Information
The RN 120 C is a smart tail light that offers enough brightness for both daytime and nighttime riding. It comes with a saddle mount and seat post mount for easy installation. The light has dimensions of (L)30(W)35(H)34mm and weighs 26g / 0.92oz. It has a charging time of approximately 1 hour using a Type-C cable and has a battery capacity of 480mAh 3.7V (1.78Wh). The tests for the light are performed indoors under a room temperature of 25 degrees Celsius with 25KM/H wind conditions. It has an IPX6 rating, providing protection against water splashes.
Product Usage Instructions
How to Install
Scheme 1:
- Attach the saddle mount or seat post mount to the RN 120 C tail light.
Scheme 2:
- Follow the instructions provided in the user manual for installation.
How to Recharge
When recharging, the light will indicate the charging status using LED lights:
- Red: Charging
- Green: Charging Completed
Operation Instructions
- ON/OFF: Press and hold the switch to turn the light on/off. The default output is the last mode when turned off.
- TURN THE BRAKE FUNCTION ON: When the light is off, press and hold the switch for 3 seconds until the light lights up constantly at the highest output.
- TURN THE BRAKE FUNCTION OFF: When the light is off, press and hold the switch for 3 seconds until the light keeps flashing quickly at the highest output.
- ADJUST BRIGHTNESS: When the light is on, single-click the switch to cycle through Low-High-Flash-ECO-Smart-Low… modes.
- MEMORY FUNCTION: When the light is turned on again, it will automatically switch to the last selected lighting mode.
- LOW POWER MODE: When the remaining battery power is low, the switch starts flashing, and the lighting mode changes to ECO mode. The brake function is disabled during this period.
- TAILLIGHT IN SLEEP MODE: When the brake sensor is on, the taillight will enter sleep mode after 5 minutes of inactivity and automatically activate any vibrations.
- BRAKE FUNCTION: When the brake sensor detects braking, the taillight will light up with maximum output.
The RN 120 C is a smart tail light that offers enough brightness for both daytime and nighttime riding.
IN THE BOX
SPECIFICATIONS
The tests are performed indoors at a room temperature of 25 degrees Celsius with 25KM/H wind conditions
HOW TO INSTALL
SCHEME 1:
SCHEME 2:
HOW TO RECHARGE
DANGER
- DO NOT expose the device or batteries to fire, explosion, or other hazards.
- DO NOT disassemble or modify the light or any of the included items.
WARNING
- Keep out of reach of children.
- The light contains a polymer battery. Certain restrictions may apply to this product when traveling, especially when traveling by air.
- Always check with your carrier for specific restrictions prior to traveling with this product.
NOTICE
- Store the light at room temperature in a dry place. Avoid moisture, or extreme heat or cold.
- Store the light in the charged condition. Avoid “deep discharge”. Battery life will decrease if the light is stored in a fully discharged condition.
- Over time, the run time of the battery will diminish. Expect about 500 full charges, depending on care. After a full life, the battery will continue to charge but with a lower run time.
OPERATION INSTRUCTIONS
- ON/OFF: Press and hold the switch to turn the light on/off. The default output is the last mode when turned off.
- TURN THE BRAKE FUNCTION ON: When the light is off, press and hold the switch for 3s until the light lights up constantly at the highest output.
- TURN THE BRAKE FUNCTION OFF: When the light is off, press and hold the switch for 3s until the light keeps flashing quickly at the highest output.
- ADJUST BRIGHTNESS: When the light is on, single-click the switch to cycle through Low-High-Flash-ECO-Smart-Low.
- MEMORY FUNCTION: When the light is turned on again, it will turn to the last selected lighting mode automatically.
- LOW POWER MODE: When the remaining battery power is low, the switch starts flashing, and the lighting mode changes to ECO mode. The brake function is disabled during this period.
- When the brake sensor is on, the taillight will enter sleep mode after 5 minutes of inaction and automatically activate any vibrations.
- When the brake sensor detects braking, the taillight will light up with maximum output.
WARRANTY
- Within 30 days of purchase: Return to the original seller for repair or replacement.
- Within 2 years of purchase: Return to Olight for repair or replacement.
- This warranty does not cover normal wear and tear, modifications, misuse, disintegrations, negligence, accidents, improper maintenance, or repair by anyone other than an Authorized retailer or Olight itself.
- USA Customer Support cs@olightstore.com
- Global Customer Support contact@olightworld.com
- Visit www.olightworld.com to see our complete product line of portable illumination tools
- Dongguan Olight E-Commerce Technology Co., Ltd 4th Floor, Building 4, Kegu Industrial Park, No 6 Zhongnan Road, Changan Town, Dongguan City, Guangdong, China.
- Made in China
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>