GEREE MR03 2K HD Doorbell Camera User Guide
- June 14, 2024
- GEREE
Table of Contents
GEREE MR03 2K HD Doorbell Camera
Note: Manual contents are subject to change without notice in accordance with our policy of continuous product improvement.
Meet the doorbell
Meet the chime
- Please mind the battery polarities when installing.
Charge your doorbell
Prior to the doorbell installation, please charge up your doorbell for about 8-10 hours till the charging LED turns BLUE from RED.
| LED STATUS | INDICATION |
|---|---|
| Solid red | Battery charging |
| Solid blue | Fully charged |
Compatible charger ( not provided ):
USB compatible mobile phone charger (DC SV 1A-2A).
App download
Search ‘Cloud Edge’ in the App stores or scan below OR codes to download the App.
ios
Android
---|---|---
Set up doorbell
-
Press your doorbell to activate, and you will see the LED indicator flashes red (once per second). If not, press and hold reset button for 5 seconds to restore factory defaults.
-
Start setting up your doorbell following the in-app instructions.
-
Tips
- Please operate the setup near your Wi-Fi router.
- Make sure your phone is connect ing to a 2.4GHz Wi-Fi.
- Make sure the doorbell is turned on, and its indicator LED is flashing red. If not, press and hold RESET for S seconds.
- Ensure the Wi-Fi signal is good, and the Wi-Fi password is correct.
| LED STATUS | INDICATION |
|---|---|
| Solid red | Device is abnormal. |
| Flash red (once/sec) | Ready for Wi-Fi configuration |
| Flash red (twice/sec) | Connecting to Wi-Fi |
| Solid blue | Device is online |
| Flash blue [once/sec) | Live-viewing doorbell cam |
| Flash blue [twice/sec) | Firmware upgrading |
Pair with your indoor chime
-
Long press the above button of Chime and the chime is on the pair status for 20 seconds and then red LED light flash
-
Press the doorbell button to send a pairing signal, and your chime will sound to react, together with its blue LED flashing. Chime pairing succeeds.
-
Chime settings.
Long press: pair with doorbell
Press & hold for 5 seconds to restore factory defaults.
Short press:volume control
Click to control volume:
level 1: 110 dB; level 2: 100 dB
level 3: 90 dB; level 4: 80 dB
Ringtone selection
Click to change ringtone (4 ringtones available).
Install Your doorbell
-
Select location for your doorsill.
-
Mount your doortiell.
-
A Release the rear mount using the unlock pin.
-
B Mark the screw holes with the doorbell mount.
-
C Mount the rear mount to 8 your wall with screws and tools.
-
D Adhesive tapes are optional to mount the doorbell on flat surf aces.
-
E Attach the doorbell to its rear mount, and push the doorbell to lock up.
-
F All set! Press the doorbell button to run a test.
Trouble Shooting
Q1: Is the video doorbell powered by battery?
A1: Yes, there is a Li-ion batter!:) built-in. Thanks to the low power consumption technology, a full charge lasts for more than 2 to 3 months in our lab test environment (Lab test condition: 10 events per da!:J, 15 seconds video recording per event).
Q2: Does it work with existing mechanical chime?
A2: No. The doorbell comes with a batter!:) powered wireless chime to notify people when your visitor presses the doorbell button. And our wireless chime is 100% wireless, !:JOU can place it almost everywhere you like. The transmission distance in open space is more than 100 meters (328 feet).
Q3: How many wireless chimes can be added to the doorbell?
A3: You can add several wireless chimes to work with your video doorbell. And one chime can be paired with upto 8 video doorbells.
Q4: Does it support customized Motion Detection Zones.
A4: Yes it does. You can customize the detection zone in the doorbell settings.
Q5: Does the doorbell support cloud storage?
A5: Your doorbell support local video storage by TF card . And you can also activate the cloud storage service in the App so as to back up video clips into the cloud server. There is a 7-day-free cloud recording trial service.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>