Foxpeed 2500A Portable Car Jump Starter User Manual

June 14, 2024
Foxpeed

Jump Starter
THE KING OF POWER

2500A Portable Car Jump Starter


Portable Car Jump Starter 2500A 21000mAh
For up to 8.0L GAS and 6.5L Diesel
12V for Various Vehicles
Please carefully read the instructions before using!
Perhaps there is small difference between the photo and actual product, so please turn to the actual product for detail information
Note

  1. DO NOT start any engines that exceed the maximum displacement the jump starter can bear.
  2. DO NOT crank the engine for more than 3 seconds.
  3. Allow the jump starter to cool down for at least 1 minute between each start attempt.
  4. Please ensure the device is at least 50% charged before use.

A Big Thank You
We’re thrilled that you have chosen FOXPEED jump starter.
We’re committed to providing you with high quality products that bring more convenience and enjoyment to your daily life. We also spare no effort to provide you excellent customer support. Should you have any questions or feedback about your new product, please get in touch with us any time! Email at service@foxpeed.com

PACKAGE CONTENT

AT AGLANCE

  1. Power Button
  2. LED Display
  3. Smart Jump Clamps Port
  4. Output 1 (5V/ 3A 9V/ 2A 12V/ 1.5A)
  5.  Output 2 (5V/ 2.1A)
  6. LED Flashlight/ SOS/ Warning light
  7. Power Input / Output (5V/ 3A)
  8. DC Output Port (12V/ 10A)

PARAMETER

Model G29
Capacity 77.7Wh
Size 1958838mm
Input(Output) 5V/3A
Output 1 5V/ 3A 9V/ 2A 12V/ 1.5A
Output 2 5V/ 2.1A
Start Current 1000A
Peak Current 2500A
DC Output 12V/10A
Circle Life 1000 times
Operating Temperature -20 — 60 C

HOW TO JUMP START YOUR CAR

Plug the jumper cable into the battery pack Connect the jumper clamps to the car battery (Red is positive and Black is negative) Start the car by turning on the ignition key After the car has been started, remove the plug from the battery pack and remove the clamps from the car battery
Note: Ensure the jump starter power level is 50% or more before jumping your car. Connect the positive(+)(red) clamp from the jump starter to the positive terminal of the car battery, and connect the negative (-)(black) clamp to the negative terminal of the car battery.
Apart from jump starting a car, this product can also supply power for a mobile phone, PSP, MP3/MP4, camera and other consumer electronics, and with different lighting modes.

HOW TO CHARGE CELLPHONES OR OTHER DIGITAL PRODUCTS


Plug the USB Port of the charging cable into the product USB interface| Inset the other side into the input port of the mobile phone| When connected OK, press then you can use it to charge now

HOW TO USE THE LED EMERGENCY LIGHT

Hold for 3 seconds to turn light on, then press lightly, led light will shift to SOS, flashing then press for seconds, the led light will be off

HOW TO RECHARGE THE DEVICE

Plug the charging cable In (Out) Inset the other side into the 220W(110V) power, the indication light will be flicking, which shows it is under charging
ATTENTION

  1. This device is suitable for petrol engines up to 8L and diesel engines up to 6.5L. To avoid damage to the device and potential injury, do not attempt to start an engine exceeding this capacity.
  2. Don’t crank the engine for more than 3 seconds. Allow the jump starter to cool down for at least 1 minute after each 3-second start attempt.
  3. Your jump starter will work best when it is fully charged. If it is less than 50% charged, it will be have insufficient charge to start the engine.
  4. Clear the car battery’s electrodes of dust and debris before jump starting.
  5. If the instructions are followed correctly but your vehicle still doesn’t start, please wait for 5-10 minutes and try again. Do not make repeated attempts to jump starter the engine without allowing time for the device to cool down.
  6. Do not connect the positive and negative polarity clamps together when the device is powered on.
  7. Disconnect the cables from the jump starter when not in use.
  8. Do not charge the device immediately after jump starting your vehicle. Wait at least 30 minutes before charging the device after a jump starter.
  9. To preserve longevity, discharge and recharge the device at least once every 3 months.
  10. Only use the cables provided with the jump starter or other certified cables.
  11. Do not expose the jump starter to liquids. Do not disassemble.
  12. Avoid dropping the device and exposing it to extreme temperatures.

HOW TO USE THE JUMPER CABLE?

  1. Fully insert the plug into the jump starter. THE GREEN LIGHT IS BLINKING
    This means that the jumper cable is correctly  connected to the jump starter.

  2. Connect the clamps to the vehicle battery.
    Red clamp is connected to the positive polarity (+), black clamp is connected to the negative polarity (-).
    The green light is always on All connections are right, try to start the engine (If there is no operation within 30 seconds after the connection is successful, the current is turned off, the green light is flashing, the jump start function is invalid, please reconnect to the car battery.)

  3. Press the car start button or tum the ignition switch to the START position.

  4. After the car has been started, the green light is strobing , please remove the jumper cable.

PROTECTION FUNCTION: THE RED LIGHT IS ON, AND THE BEEPS WILL BE GOING ON FOR ALONG TIME.

  • Jump starter power is low, please recharge.
  • Reverse polarity connection, please reconnect correctly.
  • The red and black damps are short-circuited, please reconnect correctly (It is stricly forbidden to short-circuit the positive and negative poles after the damp is energized.)
  • When the temperature of the jumper cable is high (265 + 5 C), waiting to cool down (S55 +5 C) before the next start.

PRECATIONS

  1. The jumper cable needs to be connected to the jump starter first, and then connected to the car battery for ignition to avoid misjudgment.
  2. Do not jump stant the car at high frequency continuously.
  3. This jumper cable is not allowed to be heated or used near fire.
  4. This jumper cable is not allowed to be put into water or disassembled or modified without authorization.
  5. Please connect the jumper cable correctly according to the requirements of the manual.
  6. When the engine is not connected to the battery, the cable clip does not support the reverse connection protection; if you remove the power cord from the car battery, do not connect it in reverse when Starting the car.

EXEMPTION FROM WARRANTY

  1. On more than manual outside the problem caused by wrong operation, our company does not undertake any responsibility.
  2. After the self-disassemble, our company does not undertake any responsibility.
  3. Beyond the shelf life of products, our company does not undertake any responsibility.

WARRANTY CARD

We offer 12 months warranty service from the date of purchase.

WARRANTY CONDITIONS:

When you need warranty service, please drop an email to service@foxpeed.com with the following information.

  1. Order receipt.
  2. Recording a short video showing the problem of the product.
  3. Product serial number.

WARRANTY RANGE:

  1. Quality problems under normal use.
  2. Damage caused by incorrect operations does not covered by warranty.
  3. Damage caused by self-disassembled, no warranty.
  4. No labels on the product, no warranty.

Thank you very much for choosing to buy a Foxpeed product. We hope that it will bring more convenience and enjoyment to your life.
Foxpeed.com

24/7
messenger Support
To leam more about FOXPEED, eves RLS MU CERI

( foxpeed.com for  ] Scan QR Code & Start Chatting

https://foxpeed.com
Made In China AMAL Lie). = -70 |
service@foxpeed.com
service@foxpeed.com
foxpeed.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals