himaly Digital Kitchen Scales Food Scale with Stainless Steel Platform 5KG Instructions

himaly Digital Kitchen Scales Food Scale with Stainless Steel Platform

5KG

MAIN FUNCTION

1. With high precision load cell
2. Water & milk volume measuring function.
3. Battery power low and over loaded warning function.
4. Zero & tare function.
5. Auto off function

The above table is for indicative only. Each product differs from one to another. For actual division, please refer to the product label.

TO REPLACE BATTERY AND CHARGE

1. 2 x 1.5V(AA/AAA)batteries Open the battery cover.Install new batteries by putting one side of the battery down first and pressing down the other side .
   (Please observe the polarity)

2. 1 pc or 2 pcs 3V CR2032 lithium batteries (included). Remove isolation sheet before use; Open battery cover and take out the used battery with the aid of a sharp object.Install new battery by putting one side of the battery beneath the battery baffle and then pressing down the other side.(Please observe the polarity)

3. If the product you bought is re-chargeable, please operate as below:

4. Please charge the product before use. Indicator light will be on when charging. It takes about 2 hours to be fully charged.

5. Please use the standard charger with 5V direct voltage, 0.5A output current or above.

6. It is recommended to charge the product every 3 months if it is not used after long time.

Note: The LCD is on when charging. In order to protect your safety, please do not use the weighing function when charging. Take off the power supply after charging before weighing.

LCD INCONS INDICATION

LCD display differs form one to another, so the above picture is indicative only.

BUTTONS FUNCTION

• MODE CHANGING, UNIT CHANGING BUTTONS:
• ON/OFF, ZERO, TARE BUTTONS:

Note

1. Above buttons are for indicative only.
2. UNIT button for some items are on bottom of the scale, please set the unit there if needed.
3. Buttons MODE and are indicative in this manual.

WEIGHING

1. Place the scale on a solid and flat surface. Place bowl (if any) on the scale.
2. Press button to turn on the scale.
3. Start weighing when LCD shows “O”. Press MODE button to convert to weighing mode.
4. Load weighing object on scale(or bowl} to start weighing. LCD will show the weight reading.
5. If the weighing object is liquid, press the MODE button to convert the scale to water or milk volume mode, it will show the volume.

VOLUME MEASURING

1. Place the scale on a solid and flat surface.
2. Press  button to turn on.
3. Press the MODE button to convert the mode to water or milk volume mode when LCD shows”O”.
4. Put a container onto the scale platform, LCD shows the weight of the container.
5. Press button for Zero or Tare.
6. Pour liquid (water or milk) into the container, LCD shows the volume of the liquid.

MODE / UNIT TRANSFER

• Press MODE button to switch the mode or unit you need after turning on the scale, it can be switch cercularly.
• There is UNIT button on base of the scale for some models, in this case, you need to set the unit with the UNIT button on base.
• Note: The unit system of scale depends on scale destination or the requirement of distributor.

ZERO & TARE FUNCTION

• To weigh different loads consecutively without removing loads from the scale. Put first Load on the scale, get weight reading. Press button to reset the ZERO
• LCD reading to “0” before adding next load. You can repeat this operation.

Condition 1: “ZERO” function

• When total sum of all loads on scale :S4% of scale’s max.weight capacity:
• LCD will show —– or 0g each time
• ZERO is pressed. —– means not stable, please wait for a moment. 0g and meanwhile an icon o on the LCD mean ZERO function is activated. Max.weight capacity remains unchanged.
• (For example: When capacity is 2000g, 4% is 80g; When capacity is 5000g, 4% is 200g)

Condition 2: “TARE” function When total sum of all loads on scale 4% of scale’s max.weight capacity:

• LCD will show —– or 0g each time
• ZERO is pressed. —– means not stable, please wait for a moment. 0g and meanwhile an icon Ton the LCD mean TARE function is activated. Max.Weight capacity is reduced by total weight of all loads.
• (For example:
• When capacity is 2000g, 4% is 80g; When capacity is 5000g, 4% is 200g)

Under this condition:

• By pressing , you can see the total weight of all loads on the scale. If you want
• to weigh more loads, just press , to reset LCD reading to ‘0’ again.

AUTO OFF (BATTERY POWER SAVING MODE)

• If there is no operation or weight changing in two minutes, scale will be auto off.

MANUALLY SHUT OFF

• To maximize battery life, always long press to turn off the scale after using.

WARNING

• OVER LOADING WARNING
• When LCD shows Err, it is over loaded{ Max capacity is shown on product), please take off the object to prevent damage to the scale.
• LOW POWER WARNING
• When LCD shows Lo, battery power is low, please change new battery(ies ).

ADVICE FOR USE & CARE

1. Clean the scale with slightly damp cloth. DO NOT immerse the scale in water or use chemical/corrosive cleaner. Keep the scale in cool dry place.
2. All plastics parts should be cleaned immediately after contact with fats, spices, vinegar and strongly flavored/colored foods. (Avoid contact with acids citrus juice.)
3. Always use the scale on a solid, flat surface, keep the scale unmoved when weighing.
4. This product is precision instrument, please handle with care; Do not strike, shake or drop the scale.
5. If fail to turn on, please check whether battery(ies) are installed or battery power is low.
6. Keep away from high temperature, do not strip the scale arbitrarily.
7. Designed for family use only, not for commercial use.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>