FEIT ELECTRIC WRAP 4C 840 IR MM 4 ft LED Warp Utility Light User Guide

FEIT ELECTRIC WRAP 4C 840 IR MM 4 ft LED Warp Utility Light

Safety Information

For your safety, always remember to:

• Tum off the power supply at the fuse or circuit breaker box before you install the fixture.
• Double-check all connections to be sure they are tight and correct.
• Wear rubber-soled shoes and work on a sturdy wooden ladder.
• Account for small parts and destroy packing material, as these may be hazardous to children.
• NOTE : This fixture is designed for use in a circuit protected by LJ a fuse or a circuit breaker. It is also designed to be installed in accordance with local electrical codes. If you are unsure about your wiring, consult a qualified electrician or local electrical inspector, and check your local electrical code.
• WARNING : Changes or modifications to this unit not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.
• NOTICE : All connections must be in accordance with local electrical standards and the National Electrical Code (N.E.C.) or Canadian Electrical Code (C.E.C) as appropriate. Remove the fixture and the mounting package from the box and make sure that no parts are missing by referencing the illustrations on the installation instructions.
• IMPORTANT : This fixture is intended to be only installed directly beneath a ceiling-mounted receptacle.

CAUTION, IMPORTANT SAFTEY INSTRUCTIONS: This portable light-emitting- diode (LED) luminaire has a polarized plug (One blade is wider than the other) as a feature to reduce risk of electric shock. This plug will fit in a polarized outlet only one way. If the plug does not fit fully in the outlet, reverse the plug. If it still does not fit, contact a qualified electrician. Never use with an extension cord unless the plug can be fully inserted. Do not alter the plug.

FCC STATEMENT
This device complies with part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation. Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation.

This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures: Reorient or relocate the receiving antenna. Increase the separation between the equipment and receiver. Connect the equipment into an outlet on a circuit different from that to which the receiver is connected. Consult the dealer or an experienced radio/TV technician for help. Any changes or modifications not expressly approved by the manufacturer could void the user’s authority to operate the equipment. CAN ICES-005 (B).

Limited Warranty

This product is warrantied to be free from defects in workmanship and materials for up to 5 years from date of purchase. If the product fails within the warranty period, please contact Feit Electric at info@feit.com , visit feit.com/contact-us or call 1-866-326-BULB (2852) for instructions on replacement or refund. REPLACEMENT OR REFUND IS YOUR SOLE REMEDY. EXCEPT TO THE EXTENT PROHIBITED BY APPLICABLE LAW, ANY IMPLIED WARRANTIES ARE LIMITED IN DURATION TO THE DURATION OF THIS WARRANTY. LIABILITY FOR INCIDENTAL OR CONSEQUENTIAL DAMAGES IS HEREBY EXPRESSLY EXCLUDED. Some states and provinces do not allow the exclusion of incidental or consequential damages, so the above limitation or exclusion may not apply to you. This warranty gives you specific legal rights, and you may also have other rights which vary from state to state or province to province.

Pre-Installation

NOTE : Hardware images are for illustration D purposes only. Actual product size may vary.

PACKAGE CONTENTS

PRODUCT DIMENSIONS

For Hanging Installation

1. Turning off the power
   Turn the power OFF at the switch, fusebox, or circuit breaker.

2. Attaching the screw hooks to a drywall ceiling
   

   • Mark the location for the wall anchors (EE) using the mounting template (QQ). The spacing between the wall anchors (EE) should be 40 inches.
   • Screw in the screw hooks (GG) into the wall anchors (EE).
   • For wood ceilings, screw in the screw hooks (GG) directly into the wood ceiling.

3. Installing the hanging chains to V-hooks

   • Press down firmly on the C-channel brackets (NN) to snap into the groove on the top of the utility fixture (FF). Slide the C-channel brackets (NN) about 40 inches apart.
   • Place the V-hook (BB) through the bottom rung of the hanging chain (AA).
   • Squeez on the V-hook (BB) and insert it through the center of the C-channel bracket (NN).

4. Attaching the hanging chains

   • Hang the hanging chains (AA) onto the screw hooks (GG) and plug in the power cord to the outlet.

5. Attaching the zip tie

   • Use the zip tie (CC) to attach the cord to the hanging chain (AA).

6. Turning on the power

   • Turn the power ON at the switch, fusebox, or the circuit breaker.
   • Turn the fixture ON/OFF using the provided remote.

7. Linking multiple fixtures (optional)

   • Link up to 6.

Ceiling Flush Mount Plug-In Installation

1. Turning off the power
   Turn the power OFF at the switch, fusebox, or circuit breaker.

2. Attaching the mounting screws and C-channel brackets

   • Position the mounting template (QQ) in the desired fixture location on the ceiling. Tape the four (4) comers of mounting template (QQ) to the ceiling. Mark the location for the mounting screws (DD) using the mounting template (QQ). The spacing between the mounting screws (DD) should be 1.1 inches and 40 inches apart.
   • Use the washers (RR) and mounting screws (DD) to mount the C-channel brackets (NN) to the ceiling. Use included wall anchors if ceiling is drywall or concrete.

3. Securing the fixture

   • Lift the utility fixture (FF) up to the to the C-channel brackets (NN). Push firmly until the C-channel brackets (NN) snap into the lenghtwise groove on the top of the utility fixture (FF). Plug in the power cord to the outlet.

4. Turning on the power

   • Turn the power ON at the switch, fusebox, or the circuit breaker.
   • Turn the fixture ON/OFF using the provided remote.

5. Linking multiple fixtures (optional)

   • Link up to 6.

Hardwire Fixture Installation

1. Turning off the power
   • Turn the power OFF at the switch, fusebox, or circuit breaker.
2. Attaching the mounting screws and C-channel brackets
   • Position the mounting template (QQ) in the desired fixture location on the ceiling. Tape the four (4) corners of mounting template (QQ) to the ceiling. Mark the location for the mounting screws (DD) using the mounting template (QQ). The spacing between the mounting screws (DD) should be 1.1 inches and 40 inches apart.
   • Use the washers (RR) and mounting screws (DD) to mount the C-channel brackets (NN) to the ceiling. Use included wall anchors if ceiling is drywall or concrete.
3. Wiring power supply to the fixture
   • Connect supply wires to the 6 inch hardwire pigtail (LL). Connect the 120V live (black) wire to the black wire. Connect the neutral (white) wire to the white wire. Connect the ground wire to the ground wire.
4. Plugging the pigtail into the fixture
   • Plug the hardwire pigtail (LL) into the socket on top of the fixture (FF).
5. Securing the fixture
   • Lift the utility fixture (FF) up to the to the C-channel brackets (NN). Push firmly until the C-channel brackets (NN) snap into the lenghtwise groove on the top of the utility fixture (FF).
6. Linking multiple fixtures (optional)
   • Linking multiple fixture flush mounted using a single junction box (optional).
   • Link up to 6.

Using the Wireless Remote

Group Programming

1. Group Programming
   • Program multiple fixtures at once by pressing down and holding a light setting.
   • While holding the desired light setting, walk closer to the fixture until it flashes.
   • The fixture will flash to verify the new setting has been received.
     NOTE : If the fixture did not flash, it did not receive a new light setting.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>