Mohard WX22A Wireless Car Charger Mount User Manual

**Mohard WX22A Wireless Car Charger Mount User Manual

**

Note: For best performance and safety, please read this manual carefully before using the product.

Product Introduction

1. Wireless Charging Area
2. Locking Nut
3. Dual Coil
4. Ambient Light
5. Clamping Arm
6. Release/Clamping Button
7. Type-C Charging Port
8. Bottom Bracket
9. Ball Joint
10. Locking Knob
11. Regular Baffle
12. Telescopic Hook
13. Triangular Baffle

User Instruction

1. Attach the air vent hook to the mount: Unscrew the pivot locking nut on the back of the mount anticlockwise, then place the nut over the ball joint, push the ball joint into the back of the mount, and finally tighten the nut clockwise.

2. Attach the mount on the car air vent: Turn the locking knob to adjust the length of the hook until the handle is locked securely onto the air vent.

Note:
There are two interchangeable baffles available: the regular baffle for square air vents and the triangular baffle for round air vents.

3. Connect the power supply to the wireless charger: Connect the power supply with the supplied cable and car charger. When the power is on, the ambient light will light up blue white, and the clamping arm and bottom bracket will open automatically.

Note:
A car charger with an output of at least 18W is required.

4. Charging your cellphone: Put the phone on the mount, the clamping arm and bottom bracket will automatically retract and clamp. Then the phone will begin charging, and the ambient light will turn off.

Note:

• Under normal charging conditions, the charger and mobile phone could be slightly hot, the temperature may rise if the mobile phone is working while charging (such as playing video). The product will automatically stop charging when over-heating, please try it again when it’s cooling down. There are two interchangeable baffles available: the regular baffle for square air vents and the triangular baffle for round air vents. A car charger with an output of at least 18W is required.
• This product contains a super capacitor, after power off the clamping arm can be opened and closed 1-3 times, in order to remove the phone after the engine is turned off.
• The charger is equipped with a foreign object detection function. When metal or magnetic objects are near the charging area, the ambient light will flash and the charger will stop charging. Please remove the relevant items to avoid affecting the wireless charging function.

Important Reminders

1. This charger is suitable for 4.7-6.9 inch phones with wireless charging, as well as Samsung Z FLIP3/Z FLIP4.
2. The maximum output power of this charger is 15W. It will automatically adjust the power output depending on the phone.
3. Please only use the cable provided with the charger. Other third-party cables may interfere with charging.
4. This charger requires a car charger that supports QC3.0 or PD fast charging. It is recommended to use the included car charger.
5. This product supports cell phone charging with a case, and the thickness of the phone case should be less than 5mm.

Precautions

1. This charger is only suitable for use inside the car, beware of rain and exposure.

2. The charger must be used within -20°C~40°C (-4°F~104°F), do not use this product to charge when the ambient temperature exceeds 40°C (104°F).

3. Before charging, make sure there are no metal or magnetic accessories on the back of the phone that could interfere with wireless charging. Coins, pieces of metal, and credit cards all affect wireless charging.

4. Please do not attempt to open the equipment, unauthorized disassembly or modification will damage equipment or related wireless charging functions.

5. Please do not throw, tap or shake the equipment, rough handling of the equipment will damage the internal circuit board and the mechanical structure.

6. Please keep the equipment dry. Do not use or store the charger in a heat or moisture place.

7. Please use a clean and moist soft cloth to clean the surface of the equipment.
   Do not use or store the equipment in dusty or dirty places.

8. Keep out of reach of children.

Specifications

In The Box

• User Manual x1

• Wireless Charger Mount x1

• Air Vent Hook x1

• Triangular Baffle x1

• Car Charger x1

• Car Charger x1

IC: 28703-WX22A

MADE IN CHINA

FCC Requirement

Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. this device may not cause harmful interference, and
2. this device must accept any interference received, including interference that may cause undesired operation.

Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses, and can radiate radio frequency energy, and if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>