MLUEE KF03 2 In 1 Jump Starter And Air Compressor User Manual

MLUEE KF03 2 In 1 Jump Starter And Air Compressor

2 in 1 Jump Starter with Air Compressor

Thank you for purchasing 2 in 1 Jump Starter with Air Compressor. Please read this user manual carefully before using the product and keep it properly for reference in the future.

Attention

1. Do not leave during inflation.
2. Please do not put the air pump near inflammable and explosive items.
3. Try to avoid moisture, sediment invasion and fall.
4. Do not put the product in a place that is too cold or too hot.
5. Do not throw the product into the fire or throw it away casually.
6. Keep the product away from the children.

Product Lists

Specification

Power on and off

Power on:
Press the power button for 3 seconds to start the pump.

Power off:
Press the power button for 3 seconds to stop the pump.

Battery indicator

Different indicators on the power indicator bar show different power.

• Four bars: Battery power = 80%
• Three bars: Battery power =60~79%
• Two bars: Battery power =30~59%
• One bar: Battery power =5~29%
• One bar flash: below 5% In low power state, need to charge before use.

Start/Stop Button

****Under the power-on state, touch the start-stop button to start the inflation and automatically stop inflation when the preset pressure value is reached.

Charging Type

Type-C charging input 5V/2A. Connect the charging cable to the inflator and the power adapter (you need to buy your own) to charge the inflator. Power indicator bar in charging state: Indicator bar flashing: charging When the indicator bar is long bright: it is full

Tips: Do not use the inflator during charging

Connect the air pipe to the air nozzle

Mountain bikes, electric bikes, motorcycles, and cars will be equipped with Schrader Valve. Inflation: Connect the Schrader Valve with the Schrader Valve interface on the high-pressure air pipe to inflate. Deflate: Press the air needle inside the air nozzle with an appropriate tool (such as a 4mm hex wrench) to deflate.

Road bikes and some mountain bikes need to use Presta Valve adapters when inflating.

1. Connect the Presta Valve adapter with the Schrader Valve interface on the high-pressure air pipe.
2. Unscrew the Presta Valve screws of the tire.
3. The Presta Valve can be connected with the converter to inflate.

Deflate: unscrew the Presta Valve, press the air nozzle can deflate.

Use a ball needle when inflating basketball, football and other balls.

• Inflation: press the ball needle and the Schrader Valve interface tightly and insert them into the ball to inflate.
• Deflate: Insert the ball needle directly into the ball hole to deflate.

Jump Starter

Connect the ignition clamp to the starting power interface, long press the power button to start, and the red and green light flashes alternately

Note: To ensure the ignition effect, please confirm that the power supply is more than 50%; When starting at zero volts, ensure that the power supply is above 75%.

Go back to the car and start the car. Take off the starting power immediately after a successful start.

Note: To ensure successful ignition, please complete the ignition within 30 seconds.

Detecting air pressure

• Short touch the start-stop key [j] to step the inflation  Mian tha air pressure reaches the preset pressure value [b], the air pump stops charging automatically. After the machine is turned on, connect the air hose to the tile object under test. The measured pressure value [a] shows the current pressure.

Application scenario switch
Short press the working mode key [d] to select 5 Inflatable scene modes, as ,

Unit switch

A short touch unit switch key you can switch the pressure display unit. Unit conversion formula as

• 1PSI=6.89KPA 1BAR=100KPA 1Kg/cm?=98 KPA

Preset Pressure

Short touch + – : When below 100PSI, adjust the preset pressure +/-0.5PSI When above 100 psi, adjust the preset pressure +/-1PSI Long touch + – : To quickly adjust the preset pressure. Note: The pump will automatically save scene switching and preset pressure values. When you use it next time, you only need to switch the scene and the preset pressure value will be automatically set.

LED Light
After startup, long touch the LED lighting button [I], long touch again to turn it off.

Quick air hose connector

• Turn clockwise to the right to tighten the air hose, and turn counterclockwise to the left to unscrew the air hose.

Pressure reset

After starting up, when the measured pressure value is not 0, press the preset

• [e] and preset – [i] buttons for 2 seconds at the same time to enter an automatic pressure reset. The characters on the display screen are all on, and the pressure reset will be completed after the countdown is completed.

Note: This product will be reset after leaving the factory. Due to the difference in altitude or sensor, when the measured pressure value is not 0, a manual reset can improve the pressure accuracy. Calibration is not recommended at high temperatures.
Any questions pls contact our Post-sale customer service: lisixliuyi@163.com

Inflation Pressure Reference
To ensure safety, please read the instruction manual to check the required air pressure of the inflatable items before inflating to avoid personal injury caused by the explosion of overinflation.

Car Tire
The range of air pressure that a car’s tires can withstand is marked on the side of the tires. The inflation pressure is related to the weight of the load. For more detailed pressure advice, please refer to the manual of the relevant vehicle.

The range of air pressure that a bike’s tires can withstand is marked on the side of the tires. The inflation pressure is related to the weight of the load. For more detailed pressure advice, please refer to the manual of the relevant vehicle.

Bicycle Tire

The inflating pressure of football, basketball, volleyball and other balls is marked around the inflating hole. The inflation pressure is related to the weight of the load. For more detailed pressure advice, please refer to the instruction manual of the relevant balls.

Balls

High-Temperature Safety Precautions

When unscrewing the air hose, the air hose and the air pipe connector [d] will generate high temperatures due to the long working time. Do not touch the air hose with your hands for a long time.

Common product’s air pressure

Malfunction Clearing

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>