ZMOON P008 Wireless Air Pump Cordless Air Pump User Manual
- June 14, 2024
- Zmoon
Table of Contents
ZMOON P008 Wireless Air Pump Cordless Air Pump
Product Care & Safety Instructions
- This product is prohibited for children under the age of 12 to use alone, and minors need to operate and use it accompanied by adults!
- Do not insert the inflation hose into the mouth, ears, nose, and eyes of humans or animals!
- Do not use this product near flammable and explosive liquids and gases (such as gas stations)!
- The inflation pressure of products such as basketballs and swimming rings is lower than the range of the air pump, and the air pump cannot be automatically stopped by preset tire pressure. Be extremely careful when using it to prevent explosions!
- To increase the inflation rate, we use a high-power motor, so the product will heat up during inflation, please be careful when disassembling the inflation tube. We have added an overload protection function, which will automatically stop after 10 minutes of continuous use, and can be used again after waiting for 3-5 minutes.
- Long periods of inactivity will shorten battery life, and it is recommended to charge it at least every three months.
Product Introduction
- LED Light
- Inflatable Hose Interface
- Type-C Charging
- USB Output(5V/1A)
- DC12V Charging by Cigarette Lighter Cable
- Display Screen
- Remaining Battery
On/Off/Confirm
- Long press for 3s to power on/off.
- Press to start/stop inflation after power on.
- Auto power off if not used within 1min
Switch Units/Lighting
- Long press for 3s to turn on/off the LED light.
- Press to switch between 4 different units: PSI, BAR,KPA, kg/cm2.
Air Pressure Adjustment
- Long press to quickly +/- the air pressure value; short press to fine-tune the air pressure value, +/-0.1(Bar) each time.
- After adjustment, wait for 3 seconds for the automatic setting to complete. At this time, press the to start the air pump to automatically inflate to the set air pressure.
Mode Switching
Operating Instructions
- Power On and Set Air Pressure: Press and hold the power button to turn on the machine. Once the monitored air pressure value is set to zero, check if the desired pressure is within the reasonable range for the tires or other objects to be inflated.
- Connecting the Inflatable Interface: Connect the corresponding inflatable accessories to the air outlet of the air pump and screw it tightly, then connect it to the car/ball you need to inflate and buckle it.
- Start Inflation: Ensure the selected inflation mode is correct, and then press the start button to activate the air pump for inflation. It will automatically stop when reaching the set value.
FAQ
| Questions | Cause & Solution |
|---|---|
| Product Not Working | Check whether the battery is in a low-power state, if so, |
please fully charge the product before use.
Inaccurate Barometric Pressure Display
| ①Check whether the connection between the inflation pipe connector and the tire valve is too tight; some vehicles cannot be connected too tightly, and the connection can be loosened gradually for testing;
②Check whether the air pressure unit is correct (the
inflation tube can be disconnected from the tire inflation nozzle, and after the inflation pump is shut down for 5 seconds, restart the operation).
After the preset tire pressure is started, the machine stops working after only one beep, and the tire pressure display is abnormal| ①The tire air nozzle is equipped with an external tire pressure monitor, which hinders the normal connection between the air pump air nozzle and the tire air nozzle, causing the air pump to fail to inflate;
②When the temperature is below freezing, please
use a lighter to slightly heat the air nozzle of the tire before inflating.
Inflatable Standard Unit Conversions| 100kpa=14.5psi=1kg=1.01bar Commonly used vehicle tire pressure is 2.3-2.5bar
Inflatable Pressure Gauge Reference Value
| Product Categories | Product Type | Reference Value |
|---|---|---|
| Vehicles | Compact cars | 2.2-2.8Bar |
| Motorcycles | Including electric motorcycles | 1.8-3.0Bar |
| Bicycles | 12/14/16 inch bicycle tires 20/22/24 inch bicycle tires 26/27.5/29 | |
| inch bicycle tires 700C road bike clincher tires 700C road bike tubular tires |
35-50PSI
40-50PSI
45-65PSI
100-130PSI
120-145PSI
Balls| Basketball Football Volleyball American Football| 7-9PSI
8-16PSI
4-5PSI
12-14PSI
Tip: The recommended pressure range for inflation is for reference only please refer to the instructions for the use of the product being inflated.
Product Parameters
| Product Dimensions | 74 x 65 x 175 mm |
|---|---|
| Input Power(Type-C) | 5V 2A |
| Input Power(Cigarette Lighter) | DC 12V |
| USB Output Power | 5V 1A |
| Length of Inflation Hose | 200mm(including nozzle) |
| Working Temperature | 14 ~ 149℉ |
Package List
- Inflatable Pump *1
- Portable Storage Bag *1
- Inflation Hose*1
- Inflation Adapters *4
- Type-C cable *1
- Cigarette Charging Cable*1
- User Manual *1
How to Contact US
- Go to the Amazon website and log in to your account.
- Go to the “Your Orders” page. You can find this by hovering over the “Account & Lists” menu and selecting “Your Orders” from the dropdown menu.
- Locate the order containing the item you purchased.
- Click on the “Contact Seller” button or the link next to the item in your order.
- You will be directed to a page where you can choose the reason for contacting the seller and enter a message.
- Provide the necessary details and describe your issue or inquiry regarding the headlight.
- Click on the “Send” or “Submit” button to send your message to the seller.
Note: The exact steps may vary slightly depending on the Amazon website or your location. If you are using the Amazon app, you can also find a similar option to contact the seller by going to your order details.