BARSKA AC10836 Mini Electro Sight Instruction Manual
- June 14, 2024
- BARSKA
Table of Contents
AC10836 Mini Electro Sight
Instruction Manual
Introduction
Thank you for choosing the BARSKA Mini-14 4×20 Electro Sight. The Mini-14 has
been specifically designed for your Mini 14 Rifle.
The Mini-14 belongs to the Electro Sight family, a series of high quality
optics with features to improve your aim.
The Mini-14 riflescope puts your Mini 14 rifle on target for up to 500 yards.
This scope has a bullet drop compensation system that is calibrated to 500
yards in 100 yard increments, with an eye relief of 2.7” making the Mini-14
ideal for fast targeting.
Mounting
ATTENTION : Make sure the gun is not loaded and ensure that the safety
lock is on, when you are handling it. Always follow safe gun handling
procedures. Never attempt to look into the sun with this,or any optical
enhancing device. Doing so may result in permanent eye damage.
It is extremely important to mount your scope properly. By mounting your scope
properly you will be setting the foundation for asecure and straight shot. A
scope that is not properly mounted,may move around causing the bullet point of
impact to be off dramatically.
It may also cause damage to your scope.
It is important to have correct rings for your scope. There is different size
rings out in the market place. If you find yourself unsure of what proper
rings are for your scope, visit your local firearms dealer or a local Gunsmith
to assist you.
If you are unsure as to how to install your scope to your firearm,do not
hesitate to visit your local gunsmith, to be assisted.
- Refer to your Mini-14 rifle instruction manual for disassembly procedure.
- Use a screwdriver to unlatch trigger guard to remove the barrel assemblyfrom the stock.
- Remove bolt lock cover and replace it with new cover plate supplied with the scope.
- Reassemble the barrel assembly by following your Mini-14 Rifle instruction manual.
- Slide the scope mount assembly into the cover plate and tighten with the screw knob.
- After many consecutive shots, it is possible that the dial may become loose, simply re-tighten the scope trying to get it tighter than before.
Zeroing
ATTENTION : All shooting should be done in an approved range or in a safe
area. Eye and ear protection should be worn at all times.
DANGER : If you used a bore sighter collimator or another bore
obstructing device, remove it before proceeding. If the barrel has been
drilled for a mount, ensure that the screws do not obstruct the bore. Do not
fire live or even blank ammunition with an obstructed barrel as any
obstruction can cause serious injury to gun and possible injury to you and
other people around you.
WARNING :Never attempt to look into the sun with this or
Zeroing Continued
any other optical enhancing device, doing so may cause permanent eye damage.
The purpose of zeroing your scope is to have the aim point the same aim point
as the fire arms iron sights.
- Place a target 100 yards away from the starting point.
- Place your fire arm on a secure, stable brace and aim at the center of the target using the iron sights.
- Look through the scope. Check to see if the reticle (crosshairs) is centered on the target. If not you will have to adjust the scope up or down, right or left.
Elevation Adjustment (up or down)
Set the Elevation Dial To 1 before adjusting
- Remove the Elevation Adjustment Cap by turning the cap counter clockwise with a nickel and not a screwdriver.
- Turn the adjustment dial as necessary. Each line equals .70 in. at 100 yards.
- Reattach the protective cover and tighten securely to help seal out moisture.
Windage Adjustment (Left or Right)
- Remove the Windage Adjustment Cap by turning the cap counter clockwise.
- Using a nickel (not a Screw driver) Turn the adjustment dial in either direction.
- Each line equals .70 in. at 100 yards.
- Reattach the protective caps and tighten securely to help moisture stay out.
NOTE : Attempting to align the scope to the iron sight is only a rough adjustment. In order to have a more precise scope adjustment, it is necessary to test a fire shot from the fire arm. BEFORE YOU TEST THE RIFLE, ENSURE THE TARGET IS SAFE AND CLEAR
Test Fire
Stabilize the firearm on a secure support and aim at a target 100 yards away.
Adjust the scope by turning the horizontal & vertical dials until your scope
and firearm are in tune. (follow the instructions above) When you are
adjusting the horizontal dial, ensure that the scope is set at the 1 mark .
Once the scope has been tuned at 100 yards you can quickly adjust it to shoot
up to 500 yards by rotating the Bullet Drop Compensator Knob. Select 1 for 100
yards, 2 for 200 yards, 3 for 300 yards and so on.
LIMITED LIFETIME WARRANTY
BARSKA Optics as manufacturer, warrants this new precision optical product to
be free of original defects in materials and or workmanship for the length of
time specified by this Warranty. This warranty does not include damage caused
by abuse, improper handling, installation, maintanance, normal wear-and-tear,
unauthorized repairs or modifications and tampering in anyway.
This warranty is limited to the original purchaser and is not transferable,
this warranty applies only to products purchased in the United States of
America and Canada.
In the event of a defect within 30 days, the consumer must return the
defective unit to the BARSKA dealer (the place of purchase) at his/her own
expense.
Beyond 30 days, Contact BARSKA either by E-mail:
info@barska.com or call us at
1-888-666-6769 BARSKA products should
be sent to us for warranty repairs. Products must be packed carefully and
sturdily to prevent damage in transit, and returned freight prepaid For
additional and updated information please visit our website at
www.barska.com
Please E-mail info@barska.com or call
1-888-666-6769 for Return Merchandise
Number (RMA#) before any returns.
NOTE : All merchandise received without a valid RMA# will be returned to
shipper at his/her own expense.
Please include all of the following when returning BARSKA products for service
and/or replacement:
- Please write your complete details (Name, Address, Telephone #, E-mail address, RMA#, etc..)
- Purchase receipt or Proof of Purchase. (Original copy)
- A brief explanation of the defect.
- A Check/Money Order of $25.00 to cover inspection, shipping and handling.
- Please allow 6-8 weeks for delivery.
This product will either be placed or repaired at the discretion of the
warrantor. If it’s a discontinued item, we will replace the product with an
equivalent product. Should the repair not be covered by this warranty, an
estimate will be sent for your approval. Non-warranty repairs or refurbishing
of optical products are always provided at a reasonable cost.
BARSKA Optics shall not be liable for any consequential, incidental and/or
contingent damages whatsoever. This warranty supersedes all previous BARSKA
Optics warranties
Please Refer to the additional Warranty insert
For more information please visit www.barska.com
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>