VEVOR 10190010215 Annular Cutter Set User Manual

June 14, 2024
VEVOR

VEVOR 10190010215 Annular Cutter Set

VEVOR 10190010215 Annular Cutter Set

Introduction

We continue to be committed to provide you tools with competitive price. “Save Half”, “Half Price” or any other similar expressions used by us only represents an estimate of savings you might benefit from buying certain tools with us compared to the major top brands and does not necessarily mean to cover all categories of tools offered by us. You are kindly reminded to verify carefully when you are placing an order with us if you are actually saving half in comparison with the top major brands.

This is the original instruction, please read all manual instructions carefully before operating. VEVOR reserves a clear interpretation no four user manual. The appearance of the product shall be subject to the product you received. Please forgive us that we won’t inform you again if there are any technology or software updates on our product.

SAFETY INSTRUCTION AND PRECAUTIONS

WARNING :
Read this material before using this product. Failure to do so can result in serious injury.

Safety Caution

For your safety please wear goggles and helmet. Do not wear loose clothes or yarn gloves.

  1. Please use hook to remove the chip to prevent injuries of hand.
  2. Before using, make sure the cutter is sound and securely. Do not use the cutter with damage.
  3. Turn off the machine immediately if the cutter gets stuck.
  4. Turn off the power before replace and disassemble cutter.
  5. Do not touch the cutter when it is working.
  6. Cutter’s tip is hard but also fragile. Please protect the cutter to prevent it tipping.

[The usage of annular cutter]
Annular cutter(Core drill). It can cutting all kinds of steel, steel pipe, cast iron, stainless steel, aluminum, copper and various non-metallic materials.

[The type]

Shank Suitable types of magnetic drill
Weldon shank Applicable to all kinds of Magnetic core drill machine. Like:

CHTOOLS、ALFRA、RUKO、HOUGEN、Rotabroach、BDS etc.
Universal shank
(Nitto shank)| Applicable to all kinds of Magnetic core drill machine, unless Fein machine .Like:CHTOOLS、 ALFRA、RUKO、HOUGEN、Rotabroach、BDS etc.
Fein shank| Applicable to Fein machine from Germany
[Method of application] Method of Application

Installation Method

  • Weldon shank (1):The handle of two planes aimat the two screw holes on the drill spindle,With a hex wrench to tighten and leavingagapof0.2-0.3mm, Back and forth with your hand to confirm socket head screw perpendicular to the two planes, then screw down the screws.
  • Universal shank(2): The handle of two planes aimat steel ball with in the drill chuck, then loaded into chuck. Universal shank can also be used socket head screws, As long as socket head screw perpendicular to the two planes.
  • Fein shank(3): Turn on insurance ring of the main shaft clockwise to the right way, let the handle end insert into directly, rotate in small range until steel ball enter into the hole.

Recommended cutting speed for high speed steel annular cutter:

Dia Material| 12-18| 19-25| 26-32| 33-39| 40-46| 47-53| 54-60| 61-65
---|---|---|---|---|---|---|---|---
carbon steel| 447-318| 301-229| 220-179| 173-146| 143-124| 121-108| 106-95| 93-88
alloy steel| 371-247| 234-178| 171-139| 135-114| 111-96| 94-84| 82-74| 73-68
stainless steel| 345-230| 217-165| 159-129| 125-106| 103-90| 88-78| 76-69| 67-63
Aluminum| 1857-1238| 1173-891| 857-696| 675-571| 557-484| 474-420| 412-371| 365-342
cast iron| 796-530| 502-382| 367-298| 289-244| 238-207| 203-180| 176-159| 156-146
cast copper| 1194-796| 754-573| 551-447| 434-367| 358-311| 304-270| 265-238| 234-220

Feed speed: The recommended feed speed is 0.08-0.12mm/Ror0.6-1.0mm/sec. Different feed speed will cause different chip and affect the performance of removal of chips.
Positioning: Chisel a positioning point in the center of the position to be drilled or mark a “cross” line with an alloy needle to ensure the accuracy of the drilled position. Note that when using the center chisel to hit the positioning point, please make sure that the center chisel is perpendicular to the surface of the workpiece to avoid affecting the smooth discharge of the cutting core
Start to drill: Make sure the button of magnetic drill machine is clean before power on. Turn on the switch of coolant liquid when start to drill. First feed slowly and feed in the normal speed after drill 1-2mm. 6. Finish drill: Turn off the power and use hook to remove the chips on the cutter after it stops.

[Notice]

The following actions will help to reduce or slow wearing and fracturing of cutter.

  1. When drilling steel parts, please make sure enough amount of cooling and use metal cutting fluid.
  2. Good rigidity of drill pipe and the guide rail gap can improve the precision of drilling and the life of the bit.
  3. Please make sure flat and clean between the magnetic holder and artifacts.
  4. Before cutting, make sure all parts to be locked surely.
  5. Drilling in the start and at the end, the drilling feed should reduce 1/3.
  6. For a large amount of fine powder material which occurs in the drilling, such as cast iron, cast copper, etc., can use compressed air instead of coolant liquid to help chip removal.
  7. Please remove the chips on the cutter, to ensure smooth chip removal.

[The solutions of common problem]

The solutions of chip core stuck:
Use nonmetallic material lightly slapping drill, or lightly pressure core material repeatedly, in order to make it loose to pop up, also can remove the bit, tap the thimble, so that it is out. The wearing of tools: Under the normal cooling, when chip appear blue-black color, it need to check the drill bit blade, when the most big wear width is 0.5mm, it needs grinding.

| Items| Description
---|---|---
1| Name| Annular Cutter
2| Model| 10190010215
3| Parameter| Shank:Weldon shank D.O.C:2″
Cutter Dia.:1″、1-1/8″、1-1/4″、1-1/2″、1-3/4″、2″
| Items| Description
---|---|---
1| Name| Annular Cutter
2| Model| 10190010216
3| Parameter| Shank:Universal shank D.O.C:2″
Cutter Dia.:1″、1-1/8″、1-1/4″、1-1/2″、1-3/4″、2″
| Items| Description
---|---|---
1| Name| Annular Cutter
2| Model| 10190010146
3| Parameter| Shank:Weldon shank D.O.C:1″
Cutter Dia.:1/2″、9/16″、11/16″、13/16″、15/16″、1-1/16″
| Items| Description
---|---|---
1| Name| Annular Cutter
2| Model| 10190010213
3| Parameter| Shank:Weldon shank D.O.C:1″
Cutter Dia.:7/16″、1/2″、9/16″、11/16″、5/8″、3/4″、13/16″、7/8″、15/16″、1″、1-1/16″
| Items| Description
---|---|---
1| Name| Annular Cutter
2| Model| 10190010214
3| Parameter| Shank:Weldon shank D.O.C:2″
Cutter Dia.:7/16″、1/2″、9/16″、11/16″、5/8″、3/4″、13/16″、7/8″、15/16″、1″、1-1/16″

Customer Support

Technical Support and E-Warranty Certificate
www.vevor.com/support

Logo

References

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals