RALPH LAUREN RL 5262 Alexendra Large Chandelier Instruction Manual

: June 4, 2024
: ralph lauren

Table of Contents

ASSEMBLY INSTRUCTIONS
Read User Manual Online (PDF format)
Download This Manual (PDF format)

Instruction Manual

ASSEMBLY INSTRUCTIONS

RALPH LAUREN RL 5262 Alexendra Large Chandelier - Fig
1

TO assemble safety cables:

Join fixture safety cables with Safety cables from the ceiling.
Wrap both safety cables around the cable lock nut.
Insert screws into both holes on the cable lock nut, and secure screws with a screwdriver.
Push the cable lock nut into the outlet box.

Alexandra Large Chandelier
Item # RL 5262
NOTICE:
This light fixture should be installed in accordance with all applicable, local installation codes, and by a person familiar with the construction and operation of it, as well as the hazards involved. Inspect items and contents carefully. If any damage or defect is found, do not install it.
Retain all packaging material until installation is complete and approved.

Carefully remove all parts from the box.
A 1/4” threaded nipple must be installed in your outlet box. Then install the threaded nipple (B) into the outlet box.
Unscrew the threaded collar on the chain end link (G) and attach it to the top ring (H). Close the threaded collar to secure the fixture body.
Let canopy (D) and lock collar (E) go through the chain (F).
With the fixture dimension as a guide, shorten the chain (F) as needed using a pair of chain pliers.
Unscrew the threaded collar on the other chain end link, raise the fixture then attach the chain end link to the ceiling loop (C). Close the threaded collar to secure.
Gently set the arm (I & J) to the center plate (L) and secure it with the spring washer and lock nut.
Thread the hickey (M) to the top of the center column component (N).
Gently set the arm (AA & O) to the center plate (N2) and secure it with the spring washer and lock nut.
Gently set the wire arm (T) to the center plate (N2) and secure using the spring washer and lock nut. Check that the arms are spaced evenly before final tightening.
Connect the hot wire (smooth edge, markings) from the arms to the main wire (smooth edge, markings) from the center plate (N2) using a wire nut (CC).
Connect the neutral wire (ribbed, no markings) from the arms to the main wire (ribbed, no markings) from the center plate (N2) using a wire nut (CC).
Wrap all connections individually with electrical tape.
Thread the threaded pipe (BB) to the hickey (N1).
Thread the tube (U) to the threaded pipe (BB).
Let the metal bowl (DD),crystal bowl (EE),crystal (V), and metal washer (Y) go through the tube (U) and secure with the finial (Z).
Unwrap the wiring from the top of the fixture body. Weave the power supply cord and the ground wire through the chain (F).
When you reach the canopy and ceiling loop, measure the wires then cut. Be certain to leave enough to connect inside the outlet box.
Strip the insulation back on the two power supply wires about 5/8″.
Twist the power supply and ground wire together and push through the center hole of the ceiling loop (C).
Connect the fixture ground (bare) wire with the ground wire from the outlet box using wire nut (A) . If your house does not have ground wire, then attach this wire to the green grounding screw inside of the outlet box.
IT IS IMPERATIVE THAT THIS FIXTURE BE GROUNDED.
Connect the fixture Neutral (ribbed, no markings) wire with the neutral wire from the outlet box using wire nut (A).
Connect the fixture Hot (smooth edge, markings) wire with the hot wire from the outlet box using wire nut (A).
DO NOT REVERSE THE HOT AND NEUTRAL CONNECTIONS OR SAFETY WILL BE COMPROMISED.
Tuck these wire connections neatly into the outlet box to secure.
Put canopy (D) to the ceiling loop (C) and secure with lock collar (E).
Attach the crystal (S & R & Q) to the top of the arm (T).
Thread the crystal column (A1) to the check ring (A).
Hang the crystal drop (B1) to the hook (B).
Hang the crystal drop (C1) to the hook (C).
Hang the crystal drop (D1) to the hook (D).
Hang the crystal drop (E1) to the hook (E).
Hang the crystal drop (F1) to the hook (F).
Hang the crystal drop (G1) to the finial hook (G).
Hang the crystal drop (H1) to the bowl holes (H).
Hang the crystal drop (I1) to the hook (I).
Thread the glass ball (J1) to the check ring (J).
Attention: All the glass balls (J1) are marked with numbers, they must be installed on the arms (J & AA) which are also marked with the same numbers.
Insert bulbs (not included) into the sockets.
Clip the shade (P) onto the bulbs.
Installation is complete, turn on the power at the fuse or circuit breaker.
Care Instructions: Clean only with a soft dry cloth or feather duster. Do not use abrasive or chemical agents.