Clarke MA50 15B Floor Scrubber Instruction Manual

Clarke MA50 15B Floor Scrubber

Product Information

Product Usage Instructions

This machine is intended for commercial use. It is constructed for use in an indoor environment and is not intended for any other use. Use only recommended accessories. All operators shall read, understand and exercise the following safety precautions:

1. Do not operate the machine:
   • Batteries emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open flames away! Keep the battery compartment open when charging.
   • Flammable materials can cause an explosion or fire. Do not use flammable materials in tanks.
   • Flammable materials or reactive metals can cause explosions or fire. Do not pick up.

Machine Components

The machine consists of various components including brushes, pads, squeegee, batteries, and tanks. Refer to the user manual for a detailed diagram of the machine components.

Machine Set Up & Installation

Follow these steps for machine setup and installation:

1. Do not connect + to +, or – to -, when disassembly or installing the batteries. It is very dangerous.
2. Charge the batteries. (Refer to the maintenance section in the user manual)
3. Perform pre-operation checks:
   • Sweep or dust mop the surface to be cleaned.
   • Check that the squeegee is properly installed.
   • Lower the squeegee with the lever.
   • Ensure batteries are fully charged.
   • Check that the brush is properly installed.

Brush/Pad Driver Installation and Disassembly

Follow these steps for brush/pad driver installation and disassembly:

1. Turn off the machine.
2. Lay down the machine in the specified position.
3. Mount the brush or pad driver onto the drive wheel hub and then rotate counterclockwise until it locks.
4. To remove the brush/pad, rotate the brush/pad clockwise until it is released from the drive hub.

Note: Only install manually. If automatically installed, it will wear a brush hub. Make sure that the tanks are empty before removing the brush.

Squeegee Installation

Follow these steps for squeegee installation:

1. Turn off the machine.
2. Pull down the squeegee lift lever to put down the squeegee in the working position.
3. Lay down the machine in the specified position.
4. Loosen the two knobs on the squeegee and slide the squeegee into the slots on the squeegee brackets.
5. Tighten the knobs securely. (unscrew the knobs, if to remove)
6. To replace the front/rear squeegee, unscrew the thumb knobs.

Solution Tank Filling

Follow these steps for solution tank filling:

1. Do not remove the Solution filter while filling.
2. Fill water into the solution tank from the inlet through a hose or bucket.
3. Do not overfill the solution tank. It is best to leave an inch from the top edge.
4. The water temperature must not exceed 40°C.

SAFETY PRECAUTIONS

This machine is intended for commercial use. It is constructed for use in an indoor environment and is not intended for any other use. Use only recommended accessories.
All operators shall read, understand, and exercise the following safety precautions:

1. Do not operate the machine:
   • Unless trained and authorized.
   • Unless you have read and understand the operator’s manual.
   • In fl ammable or explosive areas.
   • If not in proper operating condition.
   • In outdoor areas.
2. Before operating the machine:
   • Make sure all safety devices are in place and operate properly.
3. When using a machine:
   • Go slow on inclines and slippery surfaces
   • Follow all safety guidelines.
   • Be very careful when using the machine in reverse.
   • Report and fix any damage to the machine prior to operating it.
4. Before leaving or servicing the machine:
   • Stop the machine on level ground.
   • Turn off the machine.
5. When servicing machine:
   • Read the operator’s manual thoroughly prior to operating or servicing this machine.
   • Use manufacturer-supplied or approved replacement parts.
   • Secure the machine with wheel blocks prior to jacking the machine up.
   • Use an approved jack or hoist to safely elevate the machine.
   • Disconnect batteries prior to working on the machine.
   • Wear gloves when handling batteries or battery cables.
   • Avoid any contact with battery acid.
   • Avoid moving parts. Do not wear loose-fitting clothing while servicing the machine.

WARNING!

• Batteries emit hydrogen gas. Explosion or fire can result from hydrogen gas. Keep sparks and open flames away! Keep the battery compartment open when charging.
• Flammable materials can cause an explosion or fi re. Do not use fl ammable materials in tanks.
• Flammable materials or reactive metals can cause explosions or fi re. Do not pick up.

MACHINE COMPONENTS

• 1 Recovery Tank Lid
• 2 Recovery Tank
• 3 Solution Tank
• 17 Recovery Tank Latch
• 18 Vacuum Rubber Connectors
• 20 Solution Inlet
• 22 Solution Tank Drain Cap
• 23 Recovery Tank Drain Cap
• 24 Operating Triggers
• 25 Handle Adjustment Lever
• 26 Squeegee Raise/Lower Handle
• 29 Battery Charger
• 30 Battery Charge Indicators
• 31 Solution Ball Valve
• 33 Squeegee
• 37 Squeegee Blade Thumb Nuts
• 46 Control panel
• 47 Main switch
• 48 Brush motor switch
• 49 Vacuum motor switch
• 50 Solution switch
• 51 Battery indicator
• 52 Brush motor indicator
• 53 Vacuum motor indicator
• 54 Solution indicator

MACHINE SETUP & INSTALLATION

UNCRATING MACHINE
Be sure and check the packing carton for any damage. Immediately report any damage to the carrier. Check the contents of the package to ensure that the following items are included:

1. Machine
2. Batteries(x2)
3. Squeegee assembly
4. Owner’s Manual
5. Electric Battery Charger Manual (if equipped)
6. Connecting wire for battery and charger (if equipped)
7. Brush

BATTERY DISASSEMBLY AND INSTALLATION

1. Switch off the main switch. (47)
2. Remove the recovery tank. (2)
3. Remove the bolt from the batteries. (16) Remove or change batteries.
4. Install the batteries on the machine according to the diagram below.
5. Install the recovery tank.

WARNING! Do not connect+ to +, or – to-, when disassembly or installing the batteries. It is very dangerous.

BATTERY CHARGING

Charge the batteries. (see Maintenance section)

MACHINE SET UP

Pre-operation checks

1. Sweep or dust mop the surface to be cleaned.
2. Check that the squeegee is properly installed.
3. Lower the squeegee (33) with the lever. (26)
4. Ensure batteries are fully charged. (see Battery Charging section)
5. Check that the brush is properly installed.

BRUSH/PAD DRIVER INSTALLATION AND DISASSEMBLY
NOTE: Only install manually. If automatically installed, it will wear a brush hub. Make sure that the tanks are empty before removing the brush.

1. Turn off the machine.
2. Lay down the machine in the position shown in Figure 2. Pull up the lift lever (26) to raise the squeegee. (33).
3. Mount the brush or pad driver onto the drive wheel hub and then rotate counterclockwise until it locks, as indicated in Figure 3.
4. To remove the brush/pad, rotate the brush/pad clockwise until it is released from the drive hub.

WARNING! Do not turn on the machine in this position as below. In case of brush/pad come out or cause injury.

SQUEEGEE INSTALLATION

1. Turn off the machine. (47)
2. Pull down the squeegee lift lever (26) to put down the squeegee in the “working” position.
3. Lay down the machine in this position as shown in Figure 2.
4. Loosen the two knobs (55) on the squeegee and slide the squeegee into the slots on the squeegee brackets.
5. Tighten the knobs securely. (unscrew the knobs, if to remove)
6. To replace the front/rear squeegee, (56/57) unscrew the thumb knobs (37).

SOLUTION TANK FILLING

NOTE: The machine can be fi lled with a hose or bucket. Do not remove the Solution fi lter (21) while fi lling.

1. Fill water into solution tank (3) from the inlet (20) through hose or bucket.
2. Do not overfi ll the solution tank. It is best to leave a an inch from the top edge.
3. The water temperature must not exceed 40℃.

CAUTION! Use only low-foam and non-fl ammable detergents, intended for automatic scrubber applications.

SOLUTION TANK DRAINING
NOTE: Solution tank should be drained and cleaned after each scrubber operation is completed.

1. Unscrew the drain cap (22) on the bottom of solution tank. The solution/water will fl ow freely into a bucket or fl oor drain.
2. Rinse the solution tank with clean water after every use. This will help prevent chemical buildup and clogging of the solution lid.
3. Replace the drain cap. (22)

RECOVERY TANK DRAINING
NOTE: The recovery tank should be drained and cleaned after each scrubber operation is completed.

1. Turn the latch (17) on the recovery tank. Remove the recovery tank from the machine by grasping two grooves of tank and pulling up. Open the lid (1) and overturn the recovery tank to drain the dirty water into a container, or unscrew the drain cap (23) to let water drain into a bucket.
2. Clean and Rinse the recovery tank with clean water after every use.
3. Replace the recovery tank on the machine and turn the latch (17) to lock the tank in place.

MACHINE OPERATION

1. Set the handle to a comfortable height by pressing the level. (25)
2. Lower the squeegee (33) onto the oor by pulling down the lift handle. (26)
3. Turn on the main power switch. (47)
4. Turn on the brush motor switch (48) and the solution switch. (50)
5. Turn on the vacuum motor switch. (49)
6. If necessary, adjust the water flow by manually turning the ball valve. (31)
7. Pull one or both operating triggers. (24) The brush will spin & solution will begin to flow. Push the machine forward to start cleaning.

NOTE: If the battery indicator light (51) is green, the machine can be used. If it is yellow or red, the batteries must be charged.
CAUTION! Before lifting the brush, turn off the main power switch. (47) If the control panel (46) lights fl ash simultaneously, this indicates the machine is overloaded. Please turn off all the switches on the control panel (46) to reset the machine. If the problem persists, contact the authorized service provider. Operating a machine with discharged batteries may cause harm to the batteries or to the machine.

AFTER EACH USE
After scrubbing, please proceed with the below actions before storing the machine:

1. Remove the brush/pad holder.
2. Empty the tanks as shown in the previous paragraph.
3. Perform the daily maintenance procedures. (see Maintenance section)
4. Store the machine in a clean and dry place, with the brush/pad holder and the squeegee up.
5. If storing in an area that may reach freezing temperatures, be sure to drain all fluids from the machine prior to storage. Any damage caused by freezing will void the warranty.

MACHINE STORAGE
If the machine is not going to be used for more than 30 days, please proceed with the below actions:

1. Perform the procedures shown in the ‘After Each Use’ section above.
2. Disconnect the battery connector.

MAINTENANCE

The lifespan of the machine and its maximum operating safety are ensured by correct and regular maintenance. The following chart provides the scheduled maintenance. The intervals shown may vary according to individual working conditions.

WARNING!

• Maintenance procedures must be performed with the machine switched off and the batteries/battery charger cable disconnected.
• Moreover, carefully read the instructions in the Safety chapter.
• All maintenance procedures must be performed by qualified personnel, or by an authorized Service Center.
• This Manual describes only the most common maintenance procedures.
• For additional maintenance procedures, contact your local Service Center.

SCHEDULED MAINTENANCE TABLE

Clean tank, vacuum screen & check top cover

gasket

|  |  |  |
Squeegee blade check and replacement|  |  |  |
Inlet filter cleaning|  |  |  |
Screw and nut tightening check|  |  | （1）|
Lubricate rotary parts|  |  | （1）|
Check brush motor carbon brushes|  |  |  | （2）
Check vacuum motor carbon brushes|  |  |  | （2）

1. After the fi rst 8 working hours.
2. This maintenance procedure must be performed by an authorized Service Center.

BATTERY CHARGING

• NOTE: Charge the batteries when the yellow or red indicator, (51) or at the end of every work cycle.
• CAUTION! Proper battery care will extend battery life  If the machine is not equipped with an on-board battery charger, choose an external battery charger suitable for the type of batteries installed.
• WARNING! Please use Clarke Clarke-approved charger to charge the batteries.

1. Place the charger and machine in a well-ventilated area.
2. Turn machine off.(47)
3. Remove the recovery tank,(2) expose the battery compartment.
4. Plug the charging cable to the grounded wall outlet (100v~240v). Connect the charging cable to the machine socket.
5. The charging light (30) indicates the batteries are charging. A green light indicates battery charging is completed.
6. Upon the completion of charging, first, unplug the charging cable from the wall outlet and then disconnect it from the machine.
7. Replace the recovery tank.
   • NOTE: For further information about the operation of the battery charger, (29) see the charger section.

SQUEEGEE CLEANING

• NOTE: For optimal performance, the squeegee blades must be clean, dry, and undamaged.
• CAUTION! It is advisable to wear protective gloves when cleaning the squeegee because there may be sharp debris.

SQUEEGEE BLADE CHECK AND REPLACEMENT

1. Take off the squeegee as shown in the previously.
2. Check the edges of the front & rear blades for cracks. If necessary replace with new blades.
3. Unscrew six of the thumb nuts (37) to remove the blades.
4. Check the front & rear blades for cuts and tears. If damage is found, you can flip the blades once & re-install. If already flipped, please replace it with new blades.
5. Install the squeegee in the reverse order of removal.

BRUSH /PAD DRIVER CLEANING
CAUTION! It is advisable to wear protective gloves when cleaning the brush/pad because there may be sharp debris.

1. Remove the brush/pad as shown in the “Machine Use” section.
2. Clean and wash the brush/pad with water and detergent.
3. Check the brush bristles for integrity and wear. If necessary, replace the brush.
4. Check the pad for wear. If necessary, replace the pad driver.

RECOVERY TANK MAINTENANCE
CAUTION! It is advisable to wear protective gloves when cleaning the tank and vacuum/suction assembly because there may be sharp debris.

1. Move the machine to the appointed draining area.
2. Turn off the main switch. (47)
3. Remove the recovery tank, (2) clean and rinse both solution/recovery tanks, and drain out.
4. Remove the vacuum gasket & filter. Clean and re-install.
5. Check the recovery tank lid gasket and the vacuum rubber connector (18) for wear. Replace if necessary.
   • NOTE: The gasket ring of the recovery tank and the rubber connector between the two tanks create a vacuum in the tank. If necessary, replace them.

TECHNICAL DATA

TROUBLESHOOTING

The machine does not work,

indicator light (51) display red

| The batteries are discharged| Charge the batteries
Brush motor does not work, brush indicator light (52) does not turn

on.

| The PCB or key board is broken| Change the PCB or key board
Brush motor does not work, brush indicator light (52) flashes| The deck motor is overloaded| Use less aggressive brushes suitable for the floor

to be cleaned

Obstruction preventing the brush from rotating| Clean the brush hub
Vacuum system motor does not work, vacuum motor indicator light

(53) does not turn on

| The PCB or key board is broken| Change the PCB or key board
Vacuum system motor does not work, brush indicator lights (53)

flash

| The vacuum motor is overloaded| Check the vacuum motor
Insufficient vacuuming / water pickup| The recovery tank is full| Empty the recovery tank.
The hose is disconnected from the squeegee| Re-connect
Vacuum assembly is clogged| Clean or check
The squeegee is dirty, or the squeegee blades

are worn or damaged

| Clean and check the squeegee
The recovery tank do not latched closed| Lock the latch (17)
The tank cover is not properly closed, or the

gasket is damaged

| Close the cover properly or replace the gasket
The solution flow is insufficient| The solution filter is dirty| Clean the filter
The solution is empty| Refill solution tank
Solution flow control valve (31) is clogged| Clean the valve
The solution is dirty| Clean the solution
The squeegee leaves marks on

the floor.

| There is debris under the squeegee blades| Remove the debris
The squeegee blades are worn, chipped or torn| Replace the blades

ASSEMBLY

COMPLETE ASSEMBLY

Item Ref. No. Qty Description

• 1 VF89100-CL 1 Kit, Solution Tank
• 2 VF89018-CL 1 Label, Solution Tank
• 3 VF89200 1 Kit, Axle Wheel
• 4 VF14251 2 Bolt, M8x30, Hex Head
• 5 VF13514A 5 Washer, D8x1xd16.5
• 6 VF14516 4 Nut, Nylon Insert, M8
• 7 VF89831 1 Kit, Motor Mounting Plate
• 8 VF85698 2 Hex Socket Screw, M8x55
• 9 VF89030 2 Bushing
• 10 VF14258 1 Hex Socket Screw, M8x40
• 11 VF14503 1 Nut, M8
• 12 VF89400 1 Kit, Skirt Assembly
• 13 VV13664 15 Washer, D4x1xd8
• 14 VF13491 16 Ph Screw, M4x12
• 15 VF89821 1 Kit, Squeegee
• 16 VF89029A 1 Hose, Connect Squeegee
• 17 VF85420 2 Thumb Screw
• 18 VF89600-CL 1 Kit, Handle Assembly
• 19 VF89001 1 Handle Block, Left
• 20 VF89002 1 Handle Block, Right
• 21 VF89003-CAN 1 Circuit Box
• 22 VV60220S1 8 Hex Socket Screw, M6x15
• 23 VV20290 8 Washer Lock, ¢6
• 24 VF13614 14 Washer, ¢6
• 25 GT13027 1 Ph Screw, M5x45
• 26 VA13482 6 Washer, D5x1xd10
• 27 VF89004 1 Latch, Recovery Tank
• 28 VF89005 1 Spring, Press
• 29 VF89023US 1 Kit, Charger
• 30 VF89025-1 1 Plate, Main Control
• 31 VF89006 1 Circuit Cover
• 32 VF14301 2 Screw, M4x12
• 33 VF89034 4 Hex Bolt M6x50
• 33 VF89034A 2 Hex Bolt M6x55
• 34 VF89052 1 Cover, Waterproof
• 35 VF89037 1 Plug, Rubber
• 36 VF89035 6 Cover Nut, M6
• 37 VF89016 1 Label, Charge Display
• 38 VF89012 2 Handle Grip, Rubber
• 39 VF89017-CL 1 Label, Rear Housing
• 40 VF89007-1 1 Cable, Squeegee Lift
• 41 VF89008 1 Handle, Squeegee Lift
• 42 VV20509 3 Ph Screw, M5x10
• 43 VF89010 2 Rotate Axle, Squeegee Lift Cable
• 44 VF89011 1 Axle, Squeegee Lift Cable
• 45 VF89009A 2 Rotate Axle, Squeegee Lift Cable
• 46 VF89056 1 Solenoid Valve, 24v
• 47 VF14514 1 Nut, Nylon Insert, M5
• 48 VF89033 1 Hose
• 49 VF89847 1 Pipe Si, D6xd10, 0.115m
• 50 VF89848 1 Pipe Si, D4xd8, 0.115m
• 51 VF89846 1 Pipe Si, D6xd10, 0.45m
• 52 VF89830 1 Brush Assembly
• 52 VF89817 1 Pad Driver
• 53 VF85102 2 Small Clamp
• 54 VF89055 1 Rubber Plug, Charger Insert
• 55 VF89020 1 Battery, 2-12v 35ah
• 56 VF89036 1 Power Wire
• 57 VF89021 1 Kit, Battery Connect Line
• 58 VA13473 5 Ph Screw, M4x16
• 59 VF89827 1 Kit, Recovery Tank
• 60 VF85141 2 Big Clamp
• 61 VA13472 2 Ph Screw, M4x8
• 62 VS00001 1 Support, Left
• 63 VS00002 1 Support, Right
• 64 GT13054 2 Screw, M5x12
• 65 VV13650A 11 Screw, M4x10
• 66 VF14214 1 Screw, M5x8
• 67 VF89015 6 Plate
• 68 VF99010C 2 Circuit Breaker

SOLUTION TANK ASSEMBLY

Item Ref. No. Qty Description

• 1 VF89101-CL 1 Solution Tank
• 2 VF89102 2 Hose, Connect Vacuum
• 3 VF89103 2 Spring, Press
• 4 VF89104 2 Vacuum Hose
• 5 VF89200 1 Kit, Wheel Axle
• 6 VF89106 1 Plastic Plate, Hose Limit
• 7 VF89107 2 Rubber Seal
• 8 VF89115 1 Gasket
• 9 VF89110 1 Cap, Drain
• 10 VF85302 1 Rubber Bushing
• 11 VF89091 1 Solution Tap
• 12 VF89112 1 Cable Bracket
• 13 VF14200 2 Ph Screw, M6x15
• 14 VF89113 1 Seat, Inlet, Fresh Water Tank
• 15 VF89114 1 Filter, Inlet, Fresh Water Tank
• 16 VF13491 3 Ph Screw, M4x12
• 17 VV13664 3 Washer ¢4
• 18 VF89100-CL 1 Kit, Solution Tank
• 19 VF89201 1 Wheel Axle
• 20 VF89202 2 Drive Wheel, 10”
• 21 VF14563 2 Washer,Wave
• 22 VF14552 2 Snap Spring
• 23 VF89202-3 2 Cap, Wheel

BRUSH DECK ASSEMBLY

Item Ref. No. Qty Description

• 1 VF89301 1 Plate, Motor Mount
• 2 VF89302 1 Brush Motor Assembly
• 3 VF89303 4 Screw, M6x14
• 4 VF89304 1 Bolt, Dirve Belt
• 5 VF89305 1 O-Ring, Big
• 6 VF89306 1 Sealing Cover, Vacuum
• 7 VF89307 1 O-Ring, Small
• 8 VF89309 1 Kit, Vacuum Motor
• 9 VF89310 2 Bracket, Vac Motor
• 10 VF13491 3 Ph Screw, M4x12
• 11 VF89311 1 Washer, Thin
• 12 VF89312 1 Plate, Squeegee Rotate
• 13 VF89313 2 Guide Wheel, Squeegee
• 14 VA13482 2 Washer ¢5
• 15 VA13475 3 Ph Screw, M5x25
• 16 VF14514 2 Nut, Nylon Insert, M5
• 17 VF89314 1 Kit, Belt Adjustment
• 18 VF14223 1 Screw, M6x25
• 19 VF14506 4 Nut, Nylon Insert, M6
• 20 VF13614 3 Washer, ¢6
• 21 VV20058 1 Bolt, M6x25, Hex
• 22 VF89318 1 Spring
• 23 VF89319 1 Bushing, Squeegee Rotate
• 24 ZD45425 2 Bearing, 6204
• 25 VF89320 1 Bushing
• 26 VF89321 1 Drive Hub
• 27 VF89322 1 Nut, M20
• 28 VF89323 1 Drive Belt, Pj270
• 29 VF89324 1 Plate, Squeegee Lift
• 30 VF89325 1 Plate, Squeegee Bracket
• 31 VF89326 2 Rotate Bolt, Squeegee Lift
• 32 VF89823 1 Torsion Spring
• 33 VF89315 1 Plate, Belt Adjustment
• 34 VF89316 1 Bolt, Bearing
• 35 VF51126A 2 Bearing, 6201
• 36 VF89317 3 Washer, D12.2xd20x1
• 37 GT13084 1 Screw, M6x20
• 38 VF89308 1 Silencer Sponge
• 39 VV13633 1 Nut, M5
• 40 VF89337 1 Pressure Adjustment Plate
• 41 VF89092 1 Clamp Drain Hose
• 42 VV13667 2 Screw, M4x8

BRUSH SKIRT & BRUSH

Item Ref. No. Qty Description

• 1 VF89400 1 Brush Skirt Assembly
• 2 VF89401 1 Brush Skirt
• 3 VF89402 2 Wheel, Bumper
• 4 VF89403 2 Cover, Wheel
• 5 VF89404 2 Shaft
• 6 VF14401 6 Screw, St4x10
• 7 VF89838 1 Elbow
• 8 VF89830 1 Brush Assembly
• 8 VF89817 1 Pad Driver Assembly
• 9 MF-VF002-4A 6 Screw, St6.5×25
• 10 VF89803 1 Brush Hub

HANDLE CONTROL ASSEMBLY

Item Ref. No. Qty Description

• 1 VF89601A 1 Handle Tube Assy
• 2 VF89607-CL 1 Kit, Front Control Housing
• 3 80405A 4 Ph Screw, M5x12
• 4 VF89610 1 Trigger, Handle Adjustment
• 5 VF89611 1 Cable, Handle Adjustment
• 6 VF89612 1 Bushing, Guide Gear
• 7 VF89613 1 Spring, Handle Gear
• 8 VF89614 1 Gear, Handle Adjustment
• 9 VF89615 1 Trigger, Left
• 10 VF89616 1 Trigger, Right
• 11 VF89617 1 Pin, Handle Adjustment
• 12 VF89621 2 Pin, Trigger
• 13 VF89618-CAN 1 Control Housing, Rear
• 14 VF80407A 8 Ph Screw ,M5x25
• 15 VF89619-CL 1 Label, Switch
• 16 VF89608-CAN 1 Control Housing, Front
• 17 33005101 5 Ph Screw, M3x8
• 18 VF89622 5 Bolt, Insulation, M3x15
• 19 VV13617 5 Nut, M3
• 20 VF40263A 1 Switch
• 21 VF14244 2 Ph Screw, M3x20
• 22 VF89025-2 1 Circuit Board
• 23 VF89017-CL 1 Label, Control Housing

RECOVERY TANK ASSEMBLY

Item Ref. No. Qty Description

• 1 VF89701 1 Recovery Tank
• 2 VF89115 1 Gasket
• 3 VF89110 1 Cap, Drain
• 4 VF89810 1 Rubber Bushing, Tank
• 5 VF89811 1 Rubber Bushing, Tank, Grey
• 6 VF89828 1 Kit, Squeegee Suction
• 7 VF89829 1 Kit, Squeegee Vaccum
• 8 VF89716A 1 Kit, Recovery Tank Cover
• 9 VF89813 1 Base, Outlet
• 10 VF89712 1 Cover, Rubber
• 11 VA50523 4 Screw, St4x8
• 12 VF89709 1 Guide Base, Plug Vacuum
• 13 VF89711 1 Plug, Base
• 14 VF89712 1 O-Ring, Plug
• 15 VF89710 1 Plug, Cover
• 16 VF89814 1 Base, Vacuum
• 17 VF89705 1 O-Ring
• 18 VF89706 1 Cover, Vacuum
• 19 VA13477 2 Screw, St4x15
• 20 VF89077 1 Seal, Lid
• 21 VF89079 1 Seat,For Lid
• 22 VF89078 1 Seal, Lid
• 23 VV96001S 1 Lid, Recovery Tank
• 24 VF89080 6 Screw, M4x12

SQUEEGEE ASSEMBLY

Item Ref. No. Qty Description

• 1 VF89815 1 Squeegee Bracket
• 2 VF89807 1 Squeegee Blade, Front
• 2 VF89807-PU 1 Squeegee Blade, Front (Pu – Optional)
• 3 VF89808 1 Squeegee Blade, Rear
• 3 VF89808-PU 1 Squeegee Blade, Rear (Pu – Optional)
• 4 VF89504 1 Strap, Squeegee Front
• 5 VF89505 1 Strap, Squeegee Rear
• 6 VF89506 2 Wheel, Squeegee
• 7 VA13479 2 Bolt, M6x30, Hex Stainless
• 8 VF89507 2 Bolt, M6x45, Hex Stainless
• 9 VF14264 2 Bolt, M6x50, Hex Stainless
• 10 VF13614 12 Washer, D6.3xd12.6×1.2, Stainless
• 11 VF89509 6 Nut, Thumb, M6
• 12 80398A 3 Screw, M5x35
• 13 VA13482 6 Washer, D5xd10x1.0, Stainless
• 14 VF14514 3 Nut, Nylon Insert, M5
• 15 VF13491 2 Ph Screw, M4x12
• 16 VV13664 2 Washer, D4xd12x1mm, Stainless
• 17 VF89508 3 Bushing
• 18 VF89809 3 Wheel, Squeegee

ELECTRICAL

Item Ref. No. Qty Description

• 1 VF89026-1 1 Motor Wire
• 2 VF89022-2 1 Main Power Wire
• 3 VF89021 1 Battery Connect Wire
• 4 VF89036-1 1 Power Wire
• 5 VF89024 1 Charger Input Wire
• 6 VF89620 1 Kit, 4-Leg Switch
• 7 VF89025-3 1 Communication Wire

WIRING DIAGRAM

CONTACT

• 14600 21st Avenue North
• Plymouth, MN 55447-3408
• www.clarkeus.com.
• Phone: 800-253-0367
• Fax: 800-825-2753
• ©2014 Nilfi sk-Advance, Inc.
• A Nilfi sk-Advance Brand
• Model: CLARKE380B
• Form No. 56091128
• 7/2014 REV A

This book has important information for the use and safe operation of this machine. Failure to read this book prior to operatingor attempting any service or maintenance procedure to your Clarke machine could result in injury to you or to other personnel; damage to the machine or to other property could occur as well. You must have training in the operation of this machine before using it. If your operator(s) cannot read this manual, have it explained fully before attempting to operate this machine. All directions given in this book are as seen from the operator’s position at the rear of the machine.

References

• CustomerZone: Buy Nilfisk, Advance, Clarke, and Viper Parts, Accessories, and Machines | Nilfisk Official Website

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>