Krix IC-80 In-Ceiling Single Speaker Installation Guide

Krix IC-80 In-Ceiling Single Speaker Installation Guide

Congratulations on choosing Krix

Your Krix speakers are designed to reproduce the highest quality sound. To get the best performance from your speakers please read these installation instructions thoroughly as there are many factors that influence the performance of your speakers. If you have any difficulties please speak with one of our friendly authorised Krix dealers.

INSTALLATION

Before you begin

• Discuss with your local Krix distributor or installation consultant to determine the best location for your loudspeakers. Be sure to check for any obstructions, such as electrical wiring, plumbing, stud work or air conditioning ducts before commencing the (Figure 4)

• Also ensure that there is enough ceiling/ wall space to accommodate the speaker

Connecting

To ensure optimum performance it is important that your speaker system is connected properly:

• Follow the connection instructions supplied with your amplifier, CD/DVD, hard disk recorder, video player
• Install speaker cable in wall or ceiling cavity, or run cable along wall surface. Allow approximately 300mm of excess cable to facilitate loudspeaker
• Follow the connection instructions supplied with your amplifier to connect the speaker cables to Take care to assign the same cable colour or trace to the positive (+) connector on the amplifier as the positive (+) connector on the speaker.

Prepare speaker cables for connecting to speakers by neatly stripping cable ends

Care should be taken to eliminate loose strands of wire that may be present a short circuit hazard.

Installation

• Once the correct placement of the speakers has been determined, use the cardboard insert marked ‘template’ (from the internal packing) to trace the required cut-out onto the ceiling/wall. (Figure 4)
• Drill a hole inside the marked cut-out. Using a fine gyprock saw, cut around the inside of the marked cut-out. (Figure 5)
• Remove the circular offcut and insert the speaker to check the hole is the correct Enlarge the cut-out if required.
• Pull the stripped speaker cable through the ceiling/wall opening. Push and hold down the positive (+) red binding post on the speaker and insert the positive (+) wire through Take care to assign the same cable colour or trace to the positive (+) connector on the amplifier as the positive (+) connector on the speaker. Repeat connection process with the negative (-) black binding post and the negative (-) wire. (Figure 6)
• Ensure all mounting clamps are swung back against the speaker enclosure (Figure 6), so that the speaker can be easily inserted into the ceiling cut-out.
• Once the speaker has been located in the ceiling/wall, use a Philips head screwdriver to tighten all mounting screws. As the screws are tightened, the mounting clamps will automatically swing out over the gyprock and clamp the speaker in Be careful not to over tighten the screws as this may strip the clamp or crush the gyprock surface. (Figure 7)
• Gently fit the magnetic grille to the front of the speaker housing. (Figure 8)

Painting

If the speaker grille requires painting it is recommended to use a spray can for ease of application. Alternatively, it is to possible to apply acrylic or enamel paint using a small foam roller but this will require more applications to achieve a good result.

Spray can application

• Use a spray can and apply a light coat of Rotate the product at 90° intervals and apply three more light coats to ensure an even coverage.
• Be careful in applying single heavy coats of paint as there is a higher probability of blocking the holes in the
• If the grill does become blocked by paint, use a small pin or similar to release the blockage, while the paint is still

Roller application

• Peel away and discard the fabric liner from inside the grille.

• Load a foam roller with a light coverage of thin paint and then roll onto the to Try to avoiding blocking the holes in the grille. If the grille does become blocked by paint, use a small pin or similar to release the blockage, while the paint is still wet.

• Allow the paint to Apply three or more light coats to ensure an even coverage.

Read More About This Manual & Download PDF:

References

• Experience Sound | Krix

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>