HINKLEY 28810 Outdoor Wall Lamp Instruction Manual

HINKLEY 28810 Outdoor Wall Lamp Instruction

Product Information

The HINKLEY Fixture (Item No: 28810) is an indoor/outdoor lighting fixture designed for residential and commercial use. It comes with a backplate, mounting plate, glass shade, and necessary screws for installation. The fixture is adjustable using a knob and can be easily assembled following the provided instructions.

Product Usage Instructions

1. Find a clear area in which you can work.
2. Unpack the fixture and glass from the carton.
3. Carefully review the instructions prior to assembly.
4. Remove screws (1) to release the backplate (3) from the mounting plate (5).
5. Secure the mounting plate (4) to the junction box (2) using screws (4) (not provided).
6. Make wiring connections using IS-18 instructions on the next page.
7. Secure the backplate (3) to the mounting plate (5) using the previously removed screws (1).
8. Lamp fixture with an appropriate bulb (7).
9. Secure the cover (8) to the fixture shade.
10. Note: The fixture can be adjusted using a knob (6).

SAFETY WARNING: It is important to read the wiring and grounding instructions (I.S. 18) and any additional directions. Turn off the power supply during installation. If new wiring is required, consult a qualified electrician or local authorities for code requirements.

Wiring Instructions for Indoor Fixtures

1. Connect the positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to the positive fixture lead (B) using an appropriately sized twist-on connector.
2. Connect the negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to the negative fixture lead (D).
3. Refer to the grounding instructions below to complete all electrical connections.

Wiring Instructions for Outdoor Fixtures

1. Connect the positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to the positive fixture lead (B) using an appropriately sized twist-on connector.
2. Connect the negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to the negative fixture lead (D).
3. Cover the open end of connectors with silicone sealant to form a watertight seal.
4. If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.
5. Refer to the grounding instructions below to complete all electrical connections.

Grounding Instructions for Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) (see Drawing 1). Note: On straps for screw supported fixtures, first install the two mounting screws in the strap. Any remaining tapped hole may be used for the ground screw.

Contact Information

HINKLEY
33000 Pin Oak Parkway Avon Lake, OH 44012
800.446.5539 / 440.653.5500
Website: www.hinkley.com

Assembly Instructions

1. Find a clear area in which you can work.

2. Unpack fixture and glass from carton.

3. Carefully review instructions prior to assembly.

4. Remove screws (1) to release the backplate (3) from the mounting plate (5)

5. Secure mounting plate (4) to junctions box (2) using screws (4) not provided

6. Make wiring connections using IS-18 on the next next

7. Secure backplate (3) to mounting plate (5) using the previously removed screws (1)

8. Lamp fixture with appropriate bulb (7)

9. Secure cover (8) to fixture shade
   Note : fixture can be adjusted using knob (6)

SAFETY WARNING

READ WIRING AND GROUNDING INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.
Make electrical connections from supply wire to fixture lead wires. Refer to the instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections. Then refer back to this sheet to complete installation of this fixture.

wiring grounding instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

wiring instructions
Indoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on the connector – see Drawings 1 or 2.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with an appropriately sized twist on connector — see Drawings 2 or 3.

2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).

3. Cover the open end of connectors with silicone sealant to form a watertight seal.
   ˜ If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform especially.

4. Please refer to the grounding instructions below to complete all electrical connections.

grounding instructions

• Flush Mount Fixtures For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) – see Drawing 1.
  Note : On straps for screw supported fixtures, first install the two mounting screws in the strap. Any remaining tapped hole may be used for the ground screw.

• Chain Hung Fixtures

• Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.

• Post-Mount Fixtures Connect fixture ground wire (E) (typically copper or green plastic coated) to the power supply ground with an appropriately sized twist-on connector inside the post. Cover the open end of the connector with silicone sealant to form a watertight seal – see Drawing 3.

H I N K L E Y 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkley.com

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>