SUNCO LIGHTING LED Center Basket Troffer 35W Instruction Manual
- June 13, 2024
- Sunco Lighting
Table of Contents
SUNCO LIGHTING LED Center Basket Troffer 35W
Product Information
| Product Name | LED Center Basket Troffers |
|---|
Installation Instructions
- Find a qualified electrician for installation.
- Read the instructions before installing and using the luminaire.
- WARNING: RISK OF FIRE OR ELECTRICAL SHOCK – Turn off the power supply from the main circuit breaker before installing or servicing.
Installation Steps:
- Bend out the mounting tab 90 degrees on each corner. (Refer to Fig. 1)
- Use side cutters to adjust each tab to the height of the T-grid. (Refer to Fig. 2)
- Lay the fixture into the T-grid. (Refer to Fig. 3)
- Bend tabs flush against the T-grid to clear the corner for the ceiling tile. (Refer to Fig. 4)
- Use hanger wire to tie off appropriately in accordance with local building codes (screws and hanger wires supplied by installer). (Refer to Fig. 5)
- Ensure that the wiring of the last fixture in the row is properly terminated. Then make all electrical connections to the fixture. Attach the wiring access cover plate. (Refer to Fig. 6)
General Wiring Diagram
| Wire Color | Description |
|---|---|
| Black (Line) | Connect to a power source (120-277V) |
| White (Neutral) | Connect to a power source (120-277V) |
| Green (Grd) | Ground wire |
| Purple (Dim+) | Dimming control wire (+) |
| Pink (or Gray*) | Dimming control wire (-) [Note: Per NEMA rule change, |
gray-color dimming control wires will be changing to pink as a new
productions come in.]
Blue (-)| LED load wire (-)
Red (+)| LED load wire (+)
IEC Compliant Control: Dimming wires to 0-10V
Additional Information
- WARNING: Turn off the power supply from the main circuit breaker before installing or servicing. (Refer to Fig. 7)
- Wattage Switch: Adjust the wattage of the troffer.
- CCT Switch: Adjust the color temperature of the troffer.
- Slide Switches: Additional functionality switches for the transfer.
Specifications are subject to change without notice. Photos and line drawings may not be to scale and are for general reference only.
LED CENTER BASKET TROFFERS
PLEASE FIND A QUALIFIED ELECTRICIAN FOR INSTALLATION.
Please read the instructions before you install and use the luminaire.
WARNING, CAUTIONS AND OPERATING INSTRUCTIONS
- To reduce the risk of death, personal injury, or property damage from fire, electric shock, falling parts, cuts/abrasions, and other hazards read all warnings and instructions included with and on the fixture box and all fixture labels.
- Before installing, servicing, or performing routine maintenance on this equipment, follow these general precautions.
- Commercial installation, service, and maintenance of luminaires should be performed by a qualified licensed electrician.
- For the installation: If you are unsure about the installation or maintenance of the luminaires, consult a qualified licensed electrician and check your local electrical code.
- To prevent wiring damage or abrasion, do not expose wiring to the edges of sheet metal or other sharp objects.
- Do not make or alter any open holes in an enclosure of wiring or electrical components during kit installation.
WARNING: RISK OF FIRE OR ELECTRICAL SHOCK
- Turn off electrical power at the fuse or circuit breaker box before wiring the fixture to the power supply.
- Turn off the power when you perform any maintenance.
- Verify that supply voltage is correct by comparing it with the luminaire label information.
- All wiring connections should be capped with UL-approved wire connectors.
CAUTION: RISK OF INJURY
- Avoid direct eye exposure to the un-louvered light source while it is on.
- Account for small parts and destroy packing material, as these may be hazardous to children.
- Risk of burn. Disconnect power and allow the fixture to cool before changing the bulb or handling the fixture.
- Green ground screw provided in the proper location. DO NOT RELOCATE.
- Minimum 90° supply connectors.
- Suitable for Dry or Damp locations, Type IC
WARNING – TURN OFF THE POWER SUPPLY FROM THE MAIN CIRCUIT BREAKER BEFORE INSTALLING! OR SERVICING.
INSTALLATION
- Bend out the mounting tab 90 degrees on each corner. (Fig. 1)
- Use side cutters to adjust each tab to the height of the T-grid. (Fig. 2).
- Lay the fixture into the T-grid. (Fig. 3)
- Bend tabs flush against the T-grid in order to clear corners for ceiling tile. (Fig. 4)
- Use a #8×1/4” sheet metal screw to fasten the fixture to T-grid and use a hanger wire to tie it off appropriately in accordance with local building codes (screws and hanger wires supplied by the installer). (Fig. 5)
- Ensure that the wiring of the last fixture in the row is properly terminated. Then make all electrical connections to the fixture. Attach the wiring access cover plate. (Fig. 6)
GENERAL WIRING DIAGRAM
WARNING – TURN OFF THE POWER SUPPLY FROM THE MAIN CIRCUIT BREAKER BEFORE INSTALLING! OR SERVICING.
SPEC-SELECT™ FIXTURES – FIELD ADJUSTABLE WATTAGE & CCT (If applicable)
The end users may adjust the color temperature and lumen output, respectively,
by the two slide switches integrated into the back of the fixture. Each switch
has 3 options (left, middle, and right ), each position corresponds to 1 of 3
color temperatures (3500K, 4100K, and 5000K) and 1 of 3 wattages, which can be
adjusted to the desired combination.
- Switches are located on the back driver compartment. (Fig. 7)
- Select a wattage and color temperature by sliding the switch left or right respectively to the desired value. (Fig. 7)
Specifications are subject to change without notice. Photos and line drawings may not be to scale and are for general reference only.
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>