HEIRLOOM WHSPLV1000 Heiko Pole 12V Towel Warmer Instruction Manual
- June 4, 2024
- HEIRLOOM
Table of Contents
BATHROOMS WITH STYLE
HEIKO POLE 12V TOWEL WARMER
The Advanced Art of Towel Warming
WARNING: In order to avoid a hazard for very young children, this
appliance should be installed so that the lowest heated rail is at least 600
mm above the floor.
IMPORTANT: A means of disconnection in the fixed wiring must be used,
which is in accordance with national wiring rules (ie AS/NZS3000)
Operation
Your HEIKO POLE Towel Warmer uses only minimal electrical power – about the same as one or two LED lamps. It will take approximately 20-30 minutes to reach maximum operating temperature. HEIKO POLE Towel warmers are designed for continuous operation. NOTE: The temperature of your towel warmer will vary with the ambient temperature of your room. A towel warmer is designed to warm and assist the drying of towels and will normally operate at a temperature that is too hot for the warmer to be grasped for an extended time.
Locating Instructions
Installation instructions are shown in Fig 1 and 2. The HEIKO POLE Towel Warmer must be fixed through the wall cladding directly to studs or other suitable anchor material. The towel warmer must be located in compliance with the AS/NZS 60335 Standard. HEIKO POLE 12V towel warmers have an IP47 rating offering you the greatest flexibility to safely locate the towel warmer in bathrooms or shower rooms in Zone 1-3. All other electrical fittings must also be compliant with the zone within which the warmer is being installed.
Electrical Installation
Ensure that your towel warmer is installed by a registered electrician and
that the electrical supply, switch location and product location will comply
with regulations.
New Zealand electrical wiring requirements stipulate that this appliance must
be wired by a registered electrician in accordance with current electrical
wiring regulations.
This product must be used in conjunction with a hard-wired switch (for the
transformer). For complete temperature control, a wall-mounted dimmer switch
(with an “off” position) is recommended (in series with the transformer).
Concealed Wiring
If you have access to the wall cavity this model allows you to conceal the
electrical flex for a more streamlined and visually appealing installation.
(see Fig 2 below)
Care and Cleaning
The polished stainless steel finish of your Towel Warmer is hard-wearing and easily maintained. Clean regularly with a soft cloth and non-abrasive cleaning agent. Color finishes are more sensitive to scratching and care is required when cleaning.
Warranty
This product is warranted against defects due to faulty workmanship or
materials for 10 years from date of purchase In the event of a defect in the
product, turn it off at the wall, and contact the retailer from which it was
purchased and provide details from your sales receipt and the product’s serial
number from the label on the towel warmer. The retailer will contact Heirloom
who will assess the matter and if accepted as a valid warranty claim the
product will be repaired or replaced at Heirloom’s option – free of charge.
Costs of disconnection, reconnection and freight are the responsibility of the
owner, as is any damage arising in transit to and from servicing by Heirloom.
This warranty does not cover: a. Any damage to the product caused by misuse,
neglect, accident, or in violation of the manufacturer’s instructions, or
b. Any damage, loss or injury arising as a consequence of the use of the
product.
Australia: Our goods come with guarantees that cannot be excluded under the
Australian Consumer Law. You are entitled to a replacement or refund for a
major failure and compensation for any other reasonably foreseeable loss or
damage. You are also entitled to have the goods repaired or replaced if the
goods fail to be of acceptable quality and the failure does not amount to a
major failure.
INSTALLATION OF HEIKO POLE TOWEL WARMER
PRODUCT 1000 POLE| Mounting Centre
(Approx )| Rating at 12 Volts AC| Voltage| IP Rating
---|---|---|---|---
WHSPLV1000 Polished stainless steel| 800 mm| 20 watts| 12V AC| IP47
WHSLVP1000N Black| 800 mm| 24 watts| 12V AC| IP47
WHSPLV1000GM Gunmetal| 800 mm| 24 watts| 12V AC| IP47
WHSPLV1000B Brushed stainless steel| 800 mm| 20 watts| 12V AC| IP47
WHSPLV1000BN Brushed Nickel| 800 mm| 20 watts| 12V AC| IP47
WHSPLV1000BB Brushed Brass| 800 mm| 20 watts| 12V AC| IP47
WHSPLV1000MW Matt White| 800 mm| 27 watts| 12V AC| IP47
WHSPLVR1000 Polished stainless steel with robe hook| 800 mm| 20 watts| 12V AC|
IP47
WHSPLV850 Polished stainless steel| 650 mm| 18 watts| 12V AC| IP47
WHSLVP850N Black| 650 mm| 21 watts| 12V AC| IP47
WHSPLV850GM Gunmetal| 650 mm| 21 watts| 12V AC| IP47
WHSPLV850B Brushed stainless steel| 650 mm| 18 watts| 12V AC| IP47
WHSPLV850BN Brushed Nickel| 650 mm| 18 watts| 12V AC| IP47
WHSPLV850BB Brushed Brass| 650 mm| 18 watts| 12V AC| IP47
WHSPLV850MW Matt White| 650 mm| 24 watts| 12V AC| IP47
This Package Contains:
- Towel Warmer
- x Mounting blocks(legs) and one wall bracket and one mounting block.
- x Mounting Screws to fix wall bracket to wall
CAUTION: Prior to installation please ensure the product is to your satisfaction. Once installed Heirloom cannot be responsible for defects in the product finish. This product is not intended for use by young children or infirmed persons without supervision. In order to avoid a hazard for very young children, this towel warmer should be installed at least 600mm from the floor. Young children should be supervised to ensure they do not play with the product. If the supply cord is damaged it must be replaced by the manufacturer, its service agent, or similarly qualified persons in order to avoid a hazard.
Installation:
The HEIKO POLE Vertical is intended for installation in a vertical
orientation, though horizontal installation is also acceptable. This towel
warmer must be installed by a registered electrician and in accordance with
local and national electrical codes. We recommend that the towel warmer be
installed vertically on a flat and uniform wall, and where possible into studs
or other suitable anchor material. If fixing to hollow cavity walls, toggle
anchors (not those supplied) or similar devices must be used.
Position the towel warmer so that the transformer is easily accessible. Cable
entry to the towel warmer can be top or bottom (or left or right). Avoid the
supply cable coming into contact with the heated parts of the towel warmer
where installation is with exposed flex. .
DO NOT APPLY POWER TO THE UNIT, OR SWITCH THE TOWEL WARMER ON BEFORE
INSTALLATION IS COMPLETE.
EXPOSED FLEX INSTALLATION: (Fig 1)
- Identify suitable mounting points, preferably in timber framing. Where this is not possible, use toggles (not supplied) . Mounting centers are 800mm or 650mm vertically (can be installed horizontally). Screw flex bracket and mounting block to the wall.
- Thread the “Flex Leg” (with plastic grommet) onto the electric flex (ensuring that the leg is facing in the correct direction). Fix the leg to the towel warmer with the two screws provided.
- Ensure the flex exits the leg through the slot with the plastic grommet. Place the towel warmer on to the two mounting blocks and tighten grub screws
- Connect flex to switch at flush box (termination pack supplied may be used)
CONCEALED FLEX INSTALLATION (Fig 2)
HEIKO POLE LV V1.4 October 2021
As above, except that the flex will pass though the hole in the wall bracket.
HEIKO POLE LV V1.4 October 2021
Documents / Resources
|
HEIRLOOM WHSPLV1000 Heiko Pole 12V Towel
Warmer
[pdf] Instruction Manual
WHSPLV1000, Heiko Pole 12V Towel Warmer, WHSPLV1000 Heiko Pole 12V Towel
Warmer
---|---
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>