HINKLEY 2232 Seabrook Medium Chandelier Instruction Manual

HINKLEY 2232 Seabrook Medium Chandelier

Product Information

The HINKLEY product is a lighting fixture that requires assembly. It comes with a shade, nipple, check ring, stem, and top loop. The fixture is designed for indoor or outdoor use and requires proper wiring and grounding for installation.

Assembly Instructions:

1. Find a clear area to work in.
2. Unpack the fixture from the carton.
3. Carefully review the instructions before starting assembly.
4. Place the shade (5) over the nipple (4) at the top of the fixture.
5. Thread the check ring (3) onto the nipple (4) to secure the shade (5).
6. Secure the stem (2) to the nipple (4).
7. Secure the top loop (1) to the stem (2).

Wiring Instructions:

Indoor Fixtures:

1. Connect the positive supply wire (A) to the positive fixture lead (B) using an appropriately sized twist-on connector.
2. Connect the negative supply wire (C) to the negative fixture lead (D).
3. Refer to the grounding instructions below to complete all electrical connections.

Outdoor Fixtures:

1. Connect the positive supply wire (A) to the positive fixture lead (B) using an appropriately sized twist-on connector.
2. Connect the negative supply wire (C) to the negative fixture lead (D).
3. Cover the open end of connectors with silicone sealant to form a watertight seal.
4. If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate and the wall.
5. Refer to the grounding instructions below to complete all electrical connections.

Grounding Instructions:

Flush Mount Fixtures:

For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) to the fixture mounting strap (M) with the ground screw (S).

Chain Hung Fixtures:

Loop the fixture ground wire (E) under the head of the ground screw (S) on the fixture mounting strap (M). Connect the loose end of the fixture ground wire directly to the ground wire of the building system using appropriately sized twist-on connectors.

Post-Mount Fixtures:

Connect the fixture ground wire (E) to the power supply ground with an appropriately sized twist-on connector inside the post.
Cover the open end of the connector with silicone sealant to form a watertight seal.

Assembly Instructions

1. Find a clear area in which you can work.
2. Unpack fixture from the carton.
3. Carefully review instructions prior to assembly.

Drawing 1-shade assembly

1. Place shade (5) over nipple (4) at the top of fixture
2. Thread check ring (3) onto nipple (4) to secure shade (5)
3. Secure stem (2) to nipple (4)
4. Secure top loop (1) to stem (2)

Wiring Grounding Instructions

SAFETY WARNING: READ WIRING AND GROUNDING INSTRUCTIONS (IS 18) AND ANY ADDITIONAL DIRECTIONS.
TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED, CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS

Wiring Instructions

Indoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth, unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector – see Drawings 1 or 2.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Please refer to the grounding instructions below to complete all electrical connections

Outdoor Fixtures

1. Connect positive supply wire (A) (typically black or the smooth unmarked side of the two-conductor cord) to positive fixture lead (B) with appropriately sized twist on connector — see Drawings 2 or 3.
2. Connect negative supply wire (C) (typically white or the ribbed, marked side of the two-conductor cord) to negative fixture lead (D).
3. Cover open end of connectors with silicone sealant to form a watertight seal.
   • If installing a wall mount fixture, use caulk to seal gaps between the fixture mounting plate (backplate) and the wall. This will help prevent water from entering the outlet box. If the wall surface is lap siding, use caulk and a fixture mounting platform specially.
4. Please refer to the grounding instructions below to complete all electrical connections.

Grounding Instructions

Flush Mount Fixtures
For positive grounding in a 3-wire electrical system, fasten the fixture ground wire (E) (typically copper or green plastic coated) to the fixture mounting strap (M) with the ground screw (S) – see Drawing 1.

Note: On straps for screw supported fixtures, first install the two mounting screws in strap. Any remaining tapped hole may be used for the ground screw.

Chain Hung Fixtures
Loop fixture ground wire (E) (typically copper or green plastic coated) under the head of the ground screw (S) on fixture mounting strap (M) and connect to the loose end of the fixture ground wire directly to the ground wire of the building system with appropriately sized twist-on connectors – see Drawing 2.

Post-Mount Fixtures
Connect fixture ground wire (E) (typically copper or green plastic coated) to power supply ground with appropriately sized twist-on connector inside post. Cover open end of connector with silicone sealant to form a watertight seal – see Drawing 3.

Hanging Instructions

SAFETY WARNING: READ WIRING AND GROUNDING
INSTRUCTIONS (I.S. 18) AND ANY ADDITIONAL DIRECTIONS. TURN POWER SUPPLY OFF DURING INSTALLATION. IF NEW WIRING IS REQUIRED,CONSULT A QUALIFIED ELECTRICIAN OR LOCAL AUTHORITIES FOR CODE REQUIREMENTS.

1. Shut off electrical current before starting. If the fixture you are replacing is turned on and off by a wall switch, simply turn the switch off. If not, remove the appropriate fuse (or open the circuit breakers) until the fixture is dead.

DO NOT restore current – either by fuse, breaker or switch – until the new fixture is completely wired and in place.

1. Fasten mounting strap (1) to outlet box (A) with the two 8-32 screws (2) — see Drawing 1.

2. Thread 2 – hex nuts (3a) and (3b) onto threaded tubing (4).

3. Thread one end of threaded tubing (4) into loop (5) a minimum of 1/2’’ to 3/4’’.
   Tighten hex nut (3a) against loop (5) to lock loop in position.

4. Thread other end of threaded tube (4) into mounting strap approximately 1/2’’.

5. Slip canopy (B) over loop (5) and adjust height of loop so half of the threaded area on the loop is exposed – see Drawing 2 below. After loop height is adjusted, tighten hex nut (3b) up against mounting strap, tighten against mounting strap to lock loop and threaded tube in position.

6. Remove mounting strap (1) from junction box (A), and thread third hex nut (3c) onto end of threaded tube (4) above the mounting strap, tighten against mounting strap to lock assembly in position.

7. Remount mounting strap to junction box.

1. Taking the chain, determine the length you require to hang the fixture.

2. Attach one end of the chain to the top loop of the fixture.

3. Now slip loop collar (6) and canopy (B) onto chain. — see Drawing 2

4. Attach other end of chain to loop (5). Get assistance for this step since fixture may be heavy and difficult to hold while attaching the chain.

5. Unwrap fixture lead wire and ground wire and weave them up through the chain.

6. Slip fixture lead wire and ground wire through center of loop (5).

7. Connect ground wire to mounting strap (1) using green ground screw (GS).

8. Make electrical connections from supply wire to fixture lead wires. Refer to instruction sheet (I.S. 18) and follow all instructions to make all necessary wiring connections.

9. Slip canopy up firmly against the ceiling and secure by turning the threaded collar (6) on loop (5) until tight.

HINKLEY LIGHTING 33000 Pin Oak Parkway Avon Lake, OH 44012 800.446.5539 / 440.653.5500 hinkleylighting.com

References

• HINKLEY - Lighting and Ceiling Fans

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>