Infinix X6711 Note 30 5G Smartphone User Manual

Infinix X6711 Note 30 5G Smartphone

Product Information

• Product Name: Infinix X6711
• Model: I
• Operating System: AndroidTM
• Front Camera : Located at the top of the phone
• Volume Keys: Located on the side of the phone, with Volume + and Volume – keys
• Power Key & Side Fingerprint Sensor: Located on the side of the phone, serves as both the power button and fingerprint sensor
• NFC: Supported

Product Usage Instructions

SIM/SD Card Installation

1. Power off the mobile phone.
2. Refer to the provided picture for SIM/SD card installation.

Charging the Phone
You can charge your device using a charger or by connecting it to a computer using a USB cable (included with the phone). It is important to use only INFINIX charger and cables, as other chargers or cables may damage the device and void your phone warranty.

Explosion diagram specification

ASM

21| RCAM LOCATION FRAME ASM| 22| F CAM FIXED FRAME ASM
23| CARD HOLDER| 24| MC SCREW M1.42.5
25| MC SCREW M1.43.0| 26| CP B-COV ASM
27| BAT| 28| FPCA MAIN
29| PCBA SUB| 30| MOTOR LINEAR
31| SPK| 32| CAP FP
33| COA CABLE 2| 34| COA CABLE 1
35| R VICE CAM CON FB| 36| R CAM RUBBER 2M
37| R CAM RUBBER QVGA| 38| SPK FRAME ASM
39| CAM FPC FOAM 2M| 40| RUBBER LT SENSOR
41| RUBBER USB| 42| RUBBER EARPHONE
---|---|---|---
43| ANT FPC MYLAR| 44| MB WP FRAME MYLAR
45| MC SCREW M1.4*3.5|  |

Know your phone

1. Front Camera
2. Volume + key
3. Volume – key
4. Power key & side fingerprint sensor
5. NFC

SIM/SD card installation

1. Power off mobile.
2. Refer to the following picture for SIM / SD card installation.

Charging the phone

• You can charge your device using a charger or by connecting it to the computer using a USB cable (which comes with the phone).
• Use only the INFINIX charger and cables. Other chargers or cables may damage the device. This will invalidate your phone warranty.

FCC

FCC Caution
Labeling requirements.
This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference.
2. This device must accept any interference received, including interference that may cause undesired operation.

Information to the user.
Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate the equipment.

Information to the user.
Note: This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one or more of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and the receiver.
• Connect the equipment to an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

Specific Absorption Rate (SAR) information
This mobile phone meets the government’s requirements for exposure to radio waves. The guidelines are based on standards that were developed by independent scientific organizations through

periodic and thorough evaluation of scientific studies. The standards include a substantial safety margin designed to assure the safety of all persons regardless of age or health.
FCC RF Exposure Information and Statement The SAR limit of the USA (FCC) is 1.6 W/kg averaging over one gram of tissue. Device type: X6711 (FCC ID: 2AIZN-X6711) has also been tested against this SAR limit. The highest SAR value reported under this standard during product certification for use at the ear is 1.121W/kg and when properly worn on the body is 0.763W/kg. This device was tested for typical body-worn operations with the back of the handset kept 10 mm from the body. To maintain compliance with FCC RF exposure requirements, use accessories that maintain a 10 mm separation distance between the user’s body and the back of the handset. The use of belt clips, holsters, and similar accessories should not contain metallic components in its assembly. The use of accessories that do not satisfy these requirements may not comply with FCC RF exposure requirements and should be avoided.

Body-worn Operation
This device was tested for typical body-worn operations. To comply with RF exposure requirements, a minimum separation distance of 1.0 cm must be maintained between the user’s body and the handset, including the antenna. Third-party belt clips, holsters, and similar accessories used by this device should not contain any metallic components. Body-worn accessories that do not meet these requirements may not comply with RF exposure requirements and should be avoided. Use only the supplied or approved antenna.

For DTS patents, see http://patents.dts.com. Manufactured under license from DTS Licensing Limited. DTS, the Symbol, & DTS and the Symbol together are registered trademarks or trademarks of DTS, Inc. in the United States and/or other countries. © DTS, Inc. All Rights Reserved.

• Operating System: AndroidTM
• Android is a trademark of Google LLC.

References

• Patents - DTS

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>