AVIGILON Ava Flex Camera User Guide
- June 13, 2024
- aVIGILON
Table of Contents
MOUNTING GUIDE
AVIGILON AVA FLEX CAMERA
AVA FLEX CAMERA
MOUNTING GUIDE
Avigilon Alta Cloud Security
IMPORTANT WARNINGS AND SAFETY INSTRUCTIONS
Avoid exposing the camera to shocks, high pressure or temperatures above
40°C.
Avoid placing the camera near fans, ventilation or other noise sources.
This will degrade audio performance.
Avoid placing the camera near fans, ventilation or other heat sources.
This will degrade sensor performance.
Avoid scratching or leaving fingerprints on the lens, this degrades image
quality. If possible, keep the protective plastic on the lens cover during
installation.
Do not clean the camera with harsh detergents, gasoline or chemicals such
as Acetone.
Do not try to repair the unit yourself. Refer all servicing of the camera to
Ava or contact a reseller.
Prolonged use of the white LEDs may affect sensor readings.
This product should be supplied by a Power over Ethernet (PoE) Power Sourcing
Equipment (PSE) compliant with IEEE 802.3af or USB-C power source rated 5V
1.5A. The power supply should be UL-listed and marked “Limited Power Source”or
“LPS”.
The camera and the PoE PSE must be installed within the same building, as
described by Environment A of the IEEE 802.3af standard.
The PoE PSE must be properly grounded.
IF T: SEAVFL23-21878
BOX CONTENTS
Cable routing alternatives
Installing the bracket
Attaching the camera and connecting the ethernet cable
ADJUSTING CAMERA ORIENTATION BY USING THE BALL JOINT
Federal Communication Commission Interference Statement
This device complies with Part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
NOTE: This equipment has been tested and found to comply with the limits for a Class A digital device, pursuant to part 15 of the FCC Rules. These limits are designed to pro-vide reasonable protection against harmful interference when the equipment is operated in a commercial environment. This equipment generates, uses, and can radiate radiofrequency energy and, if not installed and used in accordance with the instruction manual, may cause harmful interference to radio communications. Operation of this equipment in a residential area is likely to cause harmful interference in which case the user will be required to correct the interference at his own expense.
FCC Caution:
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate this equipment. This
transmitter must not be co-located or operating in conjunction with any other
antenna or transmitter.
Radiation Exposure Statement:
This equipment complies with FCC radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
minimum distance 20cm between the radiator & your body.
Industry Canada statement
This device complies with ISED’s licence-exempt RSSs. Operation is subject to
the following two conditions: (1) This device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Caution:
(i) the device for operation in the band 5150-5250 MHz is only for indoor use
to reduce the potential for harmful interference to co-channel mobile
satellite systems;
Radiation Exposure Statement:
This equipment complies with ISED radiation exposure limits set forth for an
uncontrolled environment. This equipment should be installed and operated with
greater than 20cm between the radiator & your body.
To learn more, visit: www.avigilon.com
Motorola Solutions, Inc. 500 West Monroe Street, Chicago, IL 60661 U.S.A.
motorolasolutions.com
© 2023, Avigilon Corporation. All rights reserved. MOTOROLA, MOTO, MOTOROLA
SOLUTIONS and the Stylized M Logo are trademarks or registered trademarks of
Motorola Trademark Holdings, LLC and are used under license. All other
trademarks are the property of their respective owners. 07-2023 [DS01]