SHANGZHAOYUAN X99 P4 Motherboard User Manual

X99 P4
User Manual

Specifications

X99 P4

Processor| Intel Xeon E5 V3 V4 LGA2011-3 series processor
Southbridge| H81 Chipset
RAM| Technology| Dual-channel DDR4 2133/2400MHz
Maximum Capacity| 128GB (32GB4)
Memory Slot| 4 DDR4
Rear I/O| USB| 4 USB 2.0: 2 USB3.0
Ethernet| 1 Gigabit LAN Card
Video| 0
PS/2| 2
AUDIO| 1 (Mic-in, Line-out, Line-in)
Internal connector| CFAN| 1 4PIN
SYSFAN| 1 3PIN
ATXPWR Interface| 1 SPIN Power Socket: 1 24PIN Power Socket
USB2.0| 1
USB3.0| 1
M.2| 1(NVME M.2/SATA M.2)
SATA Interface| 2 SATA 2.0; 1 SATA 3.0
JAUDIO| 1 2x5Pin
PCIe| 1 PCIe x16; 1 PCIe x1
JCMOS Port| 1
JLPC| 1
SPK Port| 1
Environment| Temperature Range| Working Environment| Storage Environment
Temperature：0～50°C
Humidity：5%~95%| Temperature: -20~70°C
Humidity: 5%~95%
Physical Size| Size| 215mm185mm / 8.46in7.28in

Overview of Components

Package List:
X99 P4 Motherboard 1
SATA Cable 1
I/O Blocking 1
LGA2011-3 Cooler Bracket Mounting Kit 1

Install CPU & Fan
Please install the CPU into the CPU socket (LGA 2011-3) as shown below.

Important

• Make sure that the motherboard supports the CPU.
• Always unplug the power cord from the power outlet before installing or removing the CPU to prevent hardware damage.
• Please retain the CPU protective cap after installing the processor.
• Do not turn on the computer if the CPU cooler is not installed, otherwise overheating and damage to the CPU may occur.
• Confirm that the CPU heatsink has formed a tight seal with the CPU before booting your system.
• Apply an even layer of thermal paste (or thermal tape) between the CPU and the heatsink to enhance heat dissipation.
• Whenever the CPU is not installed, always protect the CPU socket pins by covering the socket with a plastic cap.
• Locate the pin one of the CPU socket and the CPU. Once the CPU is positioned into its socket, place one finger down on the middle of the CPU, lowering the locking lever and latching it into the fully locked position.
• Do not force the CPU into the CPU socket before the CPU socket locking lever is lifted up, or damage to the CPU and CPU socket may occur.
• Connect the CPU heatsink’s 4pin fan power connector to the 4pin CPU fan header on the motherboard.
• Please be sure to plug in the 8-PIN power supply to power the CPU.

Install Memory
The motherboard provides 4 DDR4 DIMM slots, each with a maximum capacity of 32GB.

1. Wrench the latches on both sides of the memory slot outwards.
2. Insert the memory into the slot by aligning it with the notch in the slot.
3. Flip the latches on both sides of the slot to lock the memory.

Important

• Make sure that the motherboard supports the memory. It is recommended that memory of the same capacity, brand, speed, and chips be used.
• Always turn off the computer and unplug the power cord from the power outlet before installing the memory to prevent hardware damage.
• Memory modules have a foolproof design. A memory module can be installed in only one direction. If you are unable to insert the memory, switch the direction.
• The stability and compatibility of the installed memory module depend on the installed CPU and devices when overclocking.
• This motherboard provides 4 memory sockets and supports quad-channel Technology. Install 2 to enable dual-channel mode.
• When installing memory, please install the slot close to the CPU first, as following:

| DIMM1| DIMM2| DIMM3| DIMM4
---|---|---|---|---
1 Module| —| —| Y| —
2 Modules| Y| —| Y| —
4 Modules| Y| Y| Y| Y

(“Y”=Install memory, “- -“=No Memory)
Install Expansion Card
The motherboard provides 1 PCI Express 3.0 x16 expansion slot and 1 PCI Express 3.0 x1 expansion slot.
Place the expansion card in an available PCI Express slot and press the expansion card until it is fully inserted into the slot.

Important

• When adding or removing expansion cards, always turn off the power supply and unplug the power supply power cable from the power outlet to prevent hardware damage.
• If the expansion card is not installed correctly, it may cause a short circuit throughout the metal pins, which could burn out the expansion card or the motherboard.

Back Panel Connectors

USB 2.0 Port
The USB port supports the USB 2.0 specification. Use this port for USB devices.
USB 3.0 Port
The USB 3.0 supports the USB 3.0 specification and is compatible to the USB 2.0 specification. Use this port for USB devices.
RJ45 LAN Port
The Gigabit Ethernet LAN port provides Internet connection at up to 1000Mbps/s data rate.
The following describes the states of the LAN port LEDs.

Audio Port
Line-in Port
The line in jack. Use this audio jack for line in devices such as an optical drive, walkman, etc.
Line-out Port
The line out jack.
Mic-in Port
The Mic in jack.
PS/2 Port
The PS/2 port of the mouse is green, and the PS/2 port of the keyboard is blue.

Internal Connectors
F_PANEL1 Connector

SPEAK Connector

JAUDIO1 Connector
This connector allows you to connect audio jacks on the front panel.

| 1| MIC L| 2| Ground
---|---|---|---|---
3| MICR| 4| NC
5| Head Phone R| 6| IVIIC Detection
7| SENSE SEND| 8| No Pin
9| Head Phone L| 10| Head Phone Detection

Important

• An incorrect connection between the module connector and the motherboard header will make the device unable to work or even damage it.

SATA1: SATA 3.0 Connector; SATA3~4: SATA 2.0 Connectors
These SATA 3.0 connectors are SATA 6Gb/s interface ports. Each SATA connector supports a single SATA device.

M.2 Slot
This motherboard has 1 M.2 slot, support NVME M.2/NGFF M.2 SSD.

Insert your M.2 SSD into the M.2 slot at a 30-degree angle. Secure the M.2 SSD in place with the screw.

JCMOS1: CMOS Discharge

1. JCOMS1 (Initial state)
   The initial state covers “1” and “2”.
   If you want to discharge, please go to the next step.

2. JCOMS1 (Discharge)
   Pull out the cap to cover ”2” and 3”, and wait for about 3 minutes for the discharge to complete.

3. JCOMS 1(restitute)
   After the discharge is completed, restore the initial state of the first step

Important

• Always turn off the computer and unplug the power cord from the power outlet before discharging.

ATXPWR1, JATXPWR1: Power Connectors
With the use of the power connector, the power supply can provide enough stable power to all the components on the motherboard. Before connecting the power connector, make sure the power supply is turned off and all devices are properly installed.
24PIN for motherboard power supply.
8PIN for CPU power supply.
Important

• It is recommended that a power supply that can withstand high power consumption be used (at least 500W). If a power supply is used that does not provide the required power, the result can lead to an unstable or unbootable system.

CPU_FAN1, SYS_FAN1: Fan Connectors
CPU_FAN is a interface for CPU radiator. The 4pin fan has PWM intelligent speed regulation function, which can intelligently control the fan speed based on load and temperature changes.
SYS_FAN is the system cooling fan interface, which is generally connected to the case fan.
The 3pin fan has no PWM adjustment capability.

FUSB3: USB 3.0 Connector
The header conforms to USB 3.0 and USB 2.0 specification. This connector allows you to connect USB 3.0 ports on the front panel.

| 1| VBUS| 11| D2+
---|---|---|---|---
2| SSRX1-| 12| D2-
3| SSRX1+| 13| Ground
4| Ground| 14| SSTX2+
5| SSTX1-| 15| SSTX2-
6| SSTX1+| 16| Ground
7| Ground| 17| SST2+
8| D-| 18| SST2-
9| D+| 19| VBUS
10| NC| 20| No Pin

JUSB2: USB 2.0 Connector
The headers conform to USB 2.0 specification. This connector allows you to connect USB 2.0 port on the front panel.

| 1| VCC| 2| VCC
---|---|---|---|---
3| USBO-| 4| USB1-
5| USBO+| 6| USB1+
7| Ground| 8| Ground
9| No Pin| 10| NC

BIOS Setup

BIOS (Basic Input and Output System) records hardware parameters of the system in the CMOS on the motherboard. BIOS identifies, configures, tests and connects computer hardware to the OS immediately after a computer is turned on.
Its major functions include conducting the Power-On Self-Test (POST) during system startup, saving system parameters and loading the operating system, etc. BIOS includes a BIOS Setup program that allows the user to modify basic system configuration settings or to activate certain system features.
When the power is turned off, the battery on the motherboard supplies the necessary power to the CMOS to keep the configuration values in the CMOS.
Important

• Because BIOS flashing is potentially risky if you do not encounter problems using the current version of BIOS, it is recommended that you not flash the BIOS. To flash the BIOS, do it with caution. Inadequate BIOS flashing may result in system malfunction.

BIOS Setup
The default settings offer the optimal performance for system stability in normal conditions. It is recommended that you not alter the default settings (unless you need to) to prevent system instability or other unexpected results. Inadequately altering the settings may result in the system’s failure to boot.
Important

• BIOS items are regularly updated for better system performance. The items may be slightly different from the latest BIOS; therefore, the description is for reference only.

Enter BIOS Setup
When the computer starts up, BIOS enters the self-test process. When the self- test is completed, the following message is displayed: Press DEL key to enter Setup Menu. At this time, Press key to enter the BIOS setup.
If this message disappears before you press key, you can turn it off and then turn on your computer or press on the case to restart your computer. You can also press ++ at the same time to restart your computer.
Important

• Functions may vary depending on the product you have.

Reset BIOS
When you need to restore the default BIOS settings to resolve certain issues, there are several ways to reset the BIOS:

• Go to BIOS and press F6 to load optimized defaults.
• Short the Clear CMOS jumper on the motherboard.

Important

• Be sure the computer is off before clearing CMOS data. Please refer to the Clear CMOS jumper section for resetting BIOS.

Any problem, please feel free to contact us.

References

• JGINYUE Offcial Website

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>