TARAMPS BLOCK PART G2 Automotive Alarms User Manual

: June 13, 2024
: TARAMPS

Table of Contents

TARAMPS BLOCK PART G2 Automotive Alarms
Product Information
Product Usage Instructions
Installation Scheme
Operation
Warranty terms
Read User Manual Online (PDF format)
Download This Manual (PDF format)

TARAMPS BLOCK PART G2 Automotive Alarms

Product Information

Product Name: BLOCK PART
Manufacturer: TARAMPS ELECTRONICS LTDA
Model Number: MN_012493_R02

Technical Features

Supply Voltage: 9 to 15 Volts
Consumption: 1 to 6 mA
Engine Lock: Max. 20A
Siren Output: Only Use Dedicated Siren

Warranty Terms
Any damages resulting from problems with the product, as well as losses caused by discontinuation of use, are not covered under warranty.

Product Usage Instructions

Installation Scheme

1 – Green/White: Positive Signal Door Switch
4 – Green: Ground Signal Door Switch
5 – Black/Yellow: Alarm Siren Output
BLOCK MAX 20A
6 – Red: +12V RESET BUTTON
7 – Black: GND
2 – White/Black: Reset Button
10 – Blue: POST IGNITION
9 – Black: GND
3 – White/Black: LED +
8 – Black: LED GND

Operation Block Function

Activates when opening and closing the door with the ignition on and not pressing the RESET button.
After 50 seconds, the LED flashes and the siren goes off if installed (not included), another 20 seconds the progressive block initiates.
Definitive blockage occurs after another 30 seconds.
To CANCEL the LOCKOUT, press the RESET button at any time, the LED will flash 1(once) to indicate the lockout cancellation.

VALET Function

Temporarily cancels the Lock function.
It is used when leaving the vehicle in a parking lot, without the need to indicate the location of the Reset button (secret) to the valet.
With the ignition off, hold the Reset button until the LED flashes 2 times (5 seconds).
To cancel the valet function, turn on the ignition and press the Reset button for 1 second. The LED will flash 1x (once) confirming cancellation.

Technical Support
TARAMPS provides technical support for this product. Contact their customer service for assistance.

Installation Scheme

TARAMPS-BLOCK-PART-G2-Automotive-Alarms-

Operation

Block Function

Activates when opening and closing the door with the ignition on and not pressing the RESET button.
After 50 seconds, the LED ﬂashes and the siren goes oﬀ if installed (not included), another 20 seconds the progressive block initiates. Deﬁnitive blockage occurs after another 30 seconds.
To CANCEL the LOCKOUT, press the RESET button at any time, the LED will ﬂash 1(once) to indicate the lockout cancellation..

VALET Function

Temporarily cancels the Lock function. It is used when leaving the vehicle in a parking lot, without the need to indicate the location of the Reset button (secret) to the valet.
With the ignition oﬀ, hold the Reset button until the LED ﬂashes 2 times (5 seconds). To cancel the valet function, turn on the ignition and press the Reset button for 1 second, The LED will ﬂash 1x (once) conﬁrming cancellation.

Technical Features

TARAMPS-BLOCK-PART-G2-Automotive-Alarms-02

Warranty terms

TARAMPS, located at Rua Abílio Daguano, 274 Res. Manoel Martins – Alfredo Marcondes – SP, ZIP 19.180-000, guarantees this product against design, manufacturing, assembly and/or joint and several defects due to design flaws that make it unsuitable or inappropriate for its intended use, for a period of 24 months from the date of purchase. In the event of a defect within the warranty period, TARAMPS’ liability is limited to repairing or replacing the device manufactured by it.

This warranty excludes

Products damaged by incorrect installation, water infiltration, tampering by unauthorized individuals;
Scratched or torn warranty seal;
Cases where the product is not used under regular conditions;
Defects caused by accessories, modifications or equipment attached to the product; Natural wear components, such as batteries and others;
The product presents damage resulting from drops, impacts or the action of agents of nature (floods, lightning, etc.);
Costs of removal and reinstallation of the equipment, as well as its transport to the technical assistance post;
Damages of any type, resulting from problems with the product, as well as losses caused by discontinuation of use.

Technical Support

Factory technical assistance department
Taramps Electronics – Rua : Abílio Daguano, nº 274 – ZIP 19.180-000
Phone Number + 55(18) 3266-4050 / 99749-3391
E-mail: service@taramps.com.br

A Taramps reserves the right to change the contents of this manual without prior notice or obligation to apply the modiﬁcations to previously produced units.

Fabricado por / Manufactured by