TARAMPS TMV 307 Automotive Alarms User Manual

June 13, 2024
TARAMPS

TARAMPS TMV 307 Automotive Alarms User Manual

TMV 307

Technical Features:

  • Anti-crushing system, in compliance with CONTRAN (national traffic council) resolution, No. 468 OF 2013;
  • Opens the windows through the auxiliary alarm signal;
  • Closes the windows through the alarm signal, turning lights or lock, with pulse or negative level;
  • Smart window opening and closing, with just 1 touch on the window button;
  • Interrupts the smart closing when turning off the ignition or pressing the window button;
  • Alternating pressure relief. Open the window + – 5 cm when opening the door, and close the window when closing the door;
  • Central for conventional buttons (high current reversible with negative rest), low current positive pulse (GM), Resistive (VW and FIAT);
  • 1 minute Timer after turning off the ignition;
  • Volkswagen and FIAT rear window lock activated by the original button;
  • Transformation of the LOCK and UNLOCK signal of the original VW button into a signal for the universal electric lock kit.
  • Connection compatible with most of the main electric windows kits on the market.

ATTENTION:

You must do the JUMPERS setting before connecting the TMV 307 control unit to the harness, according to the type of button.

Note: CONVENTIONAL, COMMON, or REVERSIBLE button, it is the button that is directly connected to the electric window engine. For this type, all JUMPERS must be removed.

FIG 1.JPG

Installation sequence:

  1. Connect all wires;
  2. Set the Jumpers according to the type of BUTTON;
  3. Connect the control unit to the harness;
  4. Program the anti-crush function.

Anti-crush setting:

  1. Switch on the ignition;
  2. Close the windows with short touches on the buttons, if they are open;
  3. With the windows closed, keep the 2 buttons (driver and passenger) activated to close the windows until the automatic setting starts.
    The setup process is done in one window at a time, fully opening and closing it. At the end, the 2 windows will be closed. If any of them remain open, it indicates that the system has not been set correctly and the process must be repeated.
    If the setting failure persists, check the installation and especially the voltage of the supply that goes to the TMV, if there is a very large drop in voltage, the system will not be set correctly.

FIG 2 Anti-crush setting.JPG

Common or GM

FIG 3 Common or GM.JPG

FIAT – Rear resistive button

FIG 4 FIAT - Rear resistive button.JPG

FIAT – Front Resistive Button

FIG 5 FIAT - Front Resistive Button.JPG

VW – Rear resistive button

FIG 6 VW - Rear resistive button.JPG

VW – Front resistive button

FIG 7 VW - Front resistive button.JPG

Warranty Terms

TARAMPS, located at Rua Abílio Daguano, 274 Res. Manoel Martins – Alfredo Marcondes – SP, ZIP 19.180-000, guarantees this product against design, manufacturing, assembly and/ or joint and several defects due to design flaws that make it inappropriate for its intended use, for a period of 24 months from the date of purchase. In the event of a defect within the warranty period, TARAMPS’ liability is limited to repairing or replacing the device manufactured by it.

This warranty excludes :

  • Products damaged by incorrect installation, water infiltration, tampering by unauthorized persons;
  • Scratched or torn warranty seal;
  • Cases where the product is not used under regular conditions;
  • Malfunction caused by accessories, modifications or equipment attached to the product;
  • Natural wear components, such as batteries and others;
  • The product presents damage resulting from drops, impacts or the action of agents of nature (floods, lightning, etc.);
  • Costs of removal and reinstallation of the equipment, as well as its transport to the technical assistance post;
  • Damages of any kind, resulting from problems with the product, as well as losses caused by discontinuation of use

Factory technical support department:
Taramps Electronics: nº 274 Abílio Daguano street, – ZIP: 19.180-000 Phone numbers: (18) 3266-4050 / 99749-3391
E-mail: service@taramps.com.br

Taramps reserves the right to change the content of this manual without prior notice or obligation to apply the modifications to previously produced units

+55 18 3266-4050
0800 777 0990

Fabricado por / Manufactured by: TARAMPS ELECTRONICS LTDA
CNPJ / TAX ID: 11.273.485/0001-03
R. João Silvério, 121• Res. Manoel Martins
Alfredo Marcondes – SP
Indústria Brasileira – Made in Brazil

www.taramps.com.br

Read More About This Manual & Download PDF:

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>

Related Manuals