TARAMPS HD 2000 Amplifier Free Shipping Worldwide Instruction Manual

TARAMPS HD 2000 Amplifier Free Shipping Worldwide

Product Information

The Amplifier is a high-power audio amplifier with a power output of 2000W. It is designed to operate at both 2 ohms and 4 ohms impedance. The amplifier features a built-in crossover, high pass and low pass filters, and a bass boost function. It has a maximum frequency response of 10Hz to 80Hz and can provide up to 10dB of boost. The amplifier has a high signal-to-noise ratio of over 88dB and a power consumption of 78% efficiency.

Specifications:

• Power Output: 2000W RMS
• Impedance: 2 ohms / 4 ohms
• Crossover Frequencies: 10Hz – 80Hz
• Frequency Response: 10Hz – 20KHz (-3dB)
• Bass Boost: 0 – 10.5dB (50Hz)
• Signal-to-Noise Ratio: >88dB
• Power Consumption: 78%

Product Usage Instructions

Before using the amplifier, make sure to read and follow these instructions:

1. Ensure that the amplifier is connected to a power source with the correct voltage (12V).
2. Connect the amplifier to the audio source (CD/DVD Player) using RCA cables.
3. Make sure to connect the amplifier’s ground (GND) wire to a suitable ground point.
4. Set the crossover settings according to your preference. The high pass filter (HPF) and low pass filter (LPF) can be adjusted to control the frequency range of the amplifier’s output.
5. If desired, activate the bass boost function to enhance the low-frequency response of the amplifier.
6. Monitor the amplifier’s power consumption and adjust if necessary.
7. Ensure that the amplifier is properly cooled during use. Avoid blocking the heat sink, as it serves as a heat dissipator.

For further details on installation and warranty information,refer to the user manual provided with the product.

Term of warranty

TARAMPS, located on Abilio Daguano Street 274, Res. Manoel Martins – Alfredo Marcondes, SP – Brazil, ZIP CODE 19180-000, guarantees this product against any defects on terms of project, making, assembling, and/or with solidarity, due to project vices which cause it improper or inadequate to its original use within 12 months from the date of purchase. In case of defect during the warranty period, TARAMPS responsibility is limited to the repairing or substitution of the device of its own making.

This warranty excludes:

• Damaged products by improper installation, water infiltration, violation by unauthorized individuals;
• Tamper or torn warranty seal;
• Cases in which the product is not used in adequate conditions;
• Defects caused by accessories, modifications or features attached to the product;
• The product with damage from falling, bumps or nature related problems (flooding, lightning, etc.);
• Warranty card is not properly filled or torn;
• Costs involving uninstallation, reinstallation of equipment as well as shipment to the factory;
• Damage of any kind, due to problems in the product, as well as losses caused by discontinued use of the product.

Technical assistance

For international support, check on our website: www.taramps.com.br/en/rede- de-assistencias-tecnicas or contact direct the factory support:
Phones: +55 18 3266-4050 / +55 18 99749-3391
E-mail: service@taramps.com.br

Introduction

Congratulations on your purchase of a Taramps product.
It was developed in a modern laboratory and with the latest technology.
This manual covers all features, operations and instructions to solve any doubt that may arise during the installation. Please take some time to read it carefully in order to ensure the proper installation and the use of all benefits that this product can offer.
For questions, please call +55 (18) 3266-4050, e-mail support@taramps.com.br or visit www.taramps.com.br.

Safety requirements

To ensure proper use, please read through this manual before using the amplifier. It is specially important that you know the WARNINGS and CAUTIONS contained here.

• The installation of this amplifier must be done by a qualified professional.

• Wear safety glasses, insulated gloves and correct tools for installing this product.

• This amplifier is for use with 12V batteries. Always check the voltage before installing.

• This amplifier must be installed in a firm place with at least 1″ space around the heasink for proper heat spreading.

• Never install the amplifier in places exposed to dust, humidity and water. Pay attention to install it far from fuel tank, fuel lines, heat sources and other parts of vehicle.

• Be sure to install protection fuse or a circuit braker near to battery. Follow the ampere rating as indicated here in this manual. Use of improper fuse or circuit breaker could result in overheat, smoke, damage to product, injury or burns.

• Avoid running wires over or through sharp edges. Use rubber or plastic grommets to protect any wires routed through car’s body.

• Before make any connection to amplifier, disconnect the battery negative terminal.

• When in use, the external surface of may amplifier becomes hot. Avoid touching the heatsink area and keep childrens far from the amplifier.

• This amplifier may produce high sound pressure levels. Avoid continuous exposure to levels over 85dB to prevent permanent hearing loss.

• Output connections for speakers may have voltage levels when the amplifier is operating.
  Make sure that the amplifier is turned OFF before proceed any connection or disconnection in this terminals.

• If you want to dispose this amplifier, don’t throw it on domestic waste. It must be collected by an used electronic product disposal service for proper recycling.

Safety

As you read this manual, pay attention to the safety symbols.

CAUTION
This symbol with “CAUTION” is intended to alert the user to the presence of important instructions. Failure to heed the instructions will result in risk of injury to user or product damage.

Functions & inputs

1. INPUT (R and L): Inputs of signals to be amplified. Connect these signals to RCA outputs of Head Unit, using good quality shielded cables to avoid noise influence.

2. LEVEL: It sets the amplifier input sensitivity, which allows an optimal adjustment to the output signals levels of nearly all models of Head Unit found in the market.

3. CROSSOVER
   HIGH PASS: Variable adjustment from 10Hz to 80Hz, which determines the beginning of the amplifier operating frequency
   LOW PASS: Variable adjustment from 80Hz to Full, which determines the end of the amplifier operating frequency.

4. BASS BOOST: Boost for bass levels in 50Hz, with variable gain up to 10.5 dB.

5. MONITOR: Connection to an accessory, which function is to monitor the amplifier and it is where all information from the indicator LEDs, such as distortion (CLIP/TEMP) and protection actuation (PROT), will be displayed simultaneously.

LEDS indicators & protection systems

• Blue LED steady on:
  Indicates that the amplifier is turned on.

• Flashing yellow LED: Excessive temperature (May be caused by obstruction of the internal cooler,improper installation or poorly ventilated location).
  The HD 2000 has a thermal protection system controlled by a micro-controller, (TEMPERATURE MONITOR).
  When the amplifier reaches the temperature of approximately 85°C (185°F), the thermal protection starts working, the audio is interrupted and the yellow LED will start flashing. The fan will be functioning, in order to cool down the components quickly. Only when the amplifier reaches a safe temperature level, the audio is released and the amplifier gets back to its normal functioning.

We recommend don’t turn off the amplifier, so that the cooling time will be shorter, through the ventilation of fan.

• Blinking yellow LED according to music: Indicates that the amplifier is operating at the threshold of distortion. If the red LED also blinks, it indicates excessive distortion.

• Red LED steady on:
  Short-circuit or impedance lower than that supported at output.

• RED LED flashes 2x:
  Supply voltage less than 9V.

• RED LED flashes 3x:
  Power supply voltage greater than 16V.

Output & power supply connector

1. FAN: This amplifier has one internal ventilation fan. For perfect functioning, the amplifier must be installed in a cool and aired place with at least 1″ (25mm) space around the heasink for proper heat spreading. The usually working temperature of amplifier is 65°C.
   CAUTION The fan and ventilation openings are responsible for cooling the amplifier when itis in use, so it cannot be obstructed.

2. SPEAKER: Output (positive and negative) to transducers connection (speakers). Follow the polarity described and the minimum impedance recommended.
   To combine speakers, the resulting impedance must be taken into consideration.
   See the examples below:
   CAUTION Due to the presence of voltage at the output terminals when the product is turned on, avoid contact with them. Risk of electric shock .

3. POSITIVE POWER SUPPLY TERMINAL: Use a 4 AWG (21mm?) cable directly from the positive battery terminal with fuse (115A), as close as possible from the battery.

4. REMOTE TERMINAL: The remote Head Unit output must be connected by a 0,75mm? (18 AWG) cable.

5. NEGATIVE POWER SUPPLY TERMINAL: A 4 AWG (21 mm?) cable as short as possible must be used, connected to the negative battery pole.
   It is recommended that all cables must have tinned ends to improve electrical contact.

CAUTION Before making any connections to the power terminals, make sure that the negative () of the vehicle battery is disconnected.

Installation

CAUTION: All connections to power supply, input and output connectors must be carried out only with amplifier off.

Recommended wire gauge & fuse

• Positive/negative power supply cable……………………4 AWG
• Output cables wire gauge……………………………………….9 AWG
• Remote cable………………………………………………………18 AWG
• Protection fuse or circuit breaker……………………………115A

CAUTION
Using wire gauges below the recommendation will result in power loss and overheating of wiring.

Check polarity and never reverse power supply cables due to the risk of damage to the amplifier.
It is compulsory to install a protection fuses or circuit breakers as close as possible from batteries.

Note: In case of horns and tweeters you must install a passive filter in the positive terminal of the same ones (Consult transducer’s manufacturer manual).

CAUTION
The entire aluminum surface of the amplifier serves as a heat sink. The usually working temperature is 65°C. So, avoid contact with this surface when the amplifier is in use.

Examples of connections in the power supply input.

Note: Required battery bank capacity: At least 115Ah

Technical features

Rated power with 60Hz to 1KHz sinusoidal signal and THD <= 1%, with resistive loads, measured with Audio Precision APx525 audio analyzer or equivalent and the product at lower than 50°C case temperature and 12.6V supply voltage.
Frequency response measured at 2 times the minimum impedance.
The values as above are typical and may vary, due to electronic components tolerance or manufacturing process.
For further informations or questions, visit our website or contact TARAMPS support.

+55 18 3266-4050
Fabricado por / Manufactured by:
TARAMPS ELECTRONICS LTDA
CNPJ / TAX ID: 11.273.485/0001-03
R. João Silvério, 121 • Res. Manoel Martins
Alfredo Marcondes – SP
Indústria Brasileira – Made in Brazil
www.taramps.com.br

References

• Taramps
• Taramps | WARRANTY & REPAIR CENTERS
• Taramps | Rede de Assistências Técnicas

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>