Juniper NETWORKS AP45 Wireless Access Point Installation Guide

Juniper NETWORKS AP45 Wireless Access Point

Product Information

The AP45 is a high-performance Access Point that is equipped with four IEEE 802.11ax radios. These radios deliver 4×4 MIMO with four spatial streams, allowing for efficient multi-user (MU) or single-user (SU) mode operation. The AP45 is capable of operating simultaneously in the 6GHz band, 5GHz band, and 2.4GHz band, and it also includes a dedicated tri-band scan radio. The AP45 features several I/O ports, including a reset button, Eth0+PoE-in port for power and data transfer, Eth1+PSE-out port for power sourcing, and a USB2.0 support interface.

Product Usage Instructions

Resetting to Factory Default Settings

To reset the AP45 to its factory default settings, locate the reset button on the device. Press and hold the reset button for a few seconds until the device restarts. The AP45 will then be restored to its original factory settings.

Antenna Attachment

To attach antennas to the AP45, refer to the AP45E Antenna attachment section of the hardware installation guide for detailed instructions.

Mounting the AP45

If you are planning to mount the AP45 on a wall, make sure to use screws with a 1/4in. (6.3mm) diameter head and a length of at least 2 in. (50.8mm). The APBR-U bracket included in the AP45(E) box contains a set screw and an eyehook that can be used for wall mounting.

Overview

The AP45 contains four IEEE 802.11ax radios that deliver 4×4 MIMO with four spatial streams when operating in multi-user (MU) or single-user (SU) mode. The AP45 is capable of operating simultaneously in the 6GHz band, 5GHz band, and 2.4GHz band along with a dedicated tri-band scan radio.

I/O ports

802.3at/802.3bt PoE PD
Eth1+PSE-out| 10/100/1000BASE-T RJ45 interface + 802.3af PSE (if PoE- in is 802.3bt)
USB| USB2.0 support interface

AP45E Antenna attachment

• Step 1
  • Unscrew the antenna port covers using a T8 security torx bit.
• Step 2
  • Connect antenna to the AP
• Step 3
  • Bend the breakoff tab on the covers.
• Step 4
  • Attach the antenna port cover on the AP using a T8 security torx bit
• Step 5
  • Put a few drops of the provided glue on the 6-pin port cover screws
• Step 6
  • Place the provided lexan labels on the port cover screws with the glue

AP45 Mounting

APBR-U Mounting box options

• In a wall mount installation, please use screws that have a 1/4in. (6.3mm) diameter head with a length at least 2 in. (50.8mm).
• APBR-U that is in the AP45(E) box includes a set screw and an eyehook.

Mounting to a 9/16 inch or 15/16 inch T-bar

• Step1
  • Mount APBR-U to the t-bar
• Step2
  • Rotate APBR-U to lock to the t-bar
• Step3
  • Slide the AP with shoulder screws on the APBR-U until the lock is engaged

US single gang, 3.5 or 4 inch round junction box

• Step 1
  • Mount APBR-U to the box using two screws and the #1 holes. Make sure Ethernet cable extends thru the bracket.
• Step 2
  • Slide the AP with shoulder screws on the APBR-U until the lock is engaged

US double gang junction box

• Step 1
  • Mount APBR-U to the box using two screws and the #2 holes. Make sure Ethernet cable extends thru the bracket.
• Step 2
  • Slide the AP with shoulder screws on the APBR-U until the lock is engaged

US 4 inch square junction box

• Step 1
  • Mount APBR-U to the box using two screws and the #3 holes. Make sure Ethernet cable extends thru the bracket.
• Step 2
  • Slide the AP with shoulder screws on the APBR-U until the lock is engaged

EU junction box

• Step 1
  • Mount APBR-U to the box using two screws and the #4 holes. Make sure Ethernet cable extends thru the bracket.
• Step 2
  • Slide the AP with shoulder screws on the APBR-U until the lock is engaged

Recessed 15/16 inch T-bar

• Step 1
  • Mount the APBR-ADP-RT15 to the t-bar
• Step 2
  • Mount the APBR-U to the APBR-ADP-RT15. Rotate the APBR-U to lock to the APBR- ADP-RT15
• Step 3
  • Slide the AP with shoulder screws on the APBR-U until the lock is engaged

Recessed 9/16 inch T-bar or channel rail

• Step 1
  • Mount the APBR-ADP-CR9 to the t-bar
• Step 2
  • Mount the APBR-U to the APBR-ADP-CR9. Rotate the APBR-U to lock to the APBR- ADP-CR9
• Step 3
  • Slide the AP with shoulder screws on the APBR-U until the lock is engaged

1.5 inch T-bar

• Step 1
  • Mount the APBR-ADP-WS15 to the t-bar
• Step 2
  • Mount the APBR-U to the APBR-ADP-WS15. Rotate the APBR-U to lock to the APBR-ADP-WS15
• Step 3
  • Slide the AP with shoulder screws on the APBR-U until the lock is engaged

Threaded rod adapter (1/2″, 5/8″, or M16)

• Step 1
  • Install the APBR-ADP-T12 to the APBR-U. Rotate to lock.
• Step 2
  • Secure the APBR-ADP-T12 to the APBR-U with the provided screw
• Step 3
  • Install the bracket assembly to the 1/2″ threaded rod and secure with the provided lock washer and nut.
• Step 4
  • Slide the AP with shoulder screws on the APBR-U until the lock is engaged
  • The same instructions work for the APBR-ADP-T58 or APBR-ADP-M16

The threaded rod adapter attaches to a rod that is either 1/2″-13, 5/8″-11, or M16-2.

Technical Specifications

AP45E: 1.30 kg (2.86 lbs)

Operating temperature| AP45: 0° to 40° C

AP45E: -10° to 50° C

Operating humidity| 10% to 90% maximum relative humidity, non-condensing
Operating altitude| 3,048m (10,000 ft)
Electromagnetic emissions| FCC Part 15 Class B

I/O

| 1 – 100/1000/2500/5000BASE-T auto-sensing RJ-45 with PoE 1 – 10/100/1000BASE-T auto-sensing RJ-45

USB2.0

RF

| 2.4GHz or 5GHz – 4×4:4SS 802.11ax MU-MIMO & SU-MIMO

5GHz – 4×4:4SS 802.11ax MU-MIMO & SU-MIMO

6GHz – 4×4: 4SS 802.11ax MU-MIMO & SU-MIMO

2.4GHz / 5GHz /6GHz scanning radio 2.4GHz BLE with Dynamic Antenna Array

Maximum PHY rate

| Total maximum PHY rate – 9600 Mbps

6GHz – 4800 Mbps

5GHz – 2400 Mbps

2.4GHz or 5GHz – 1148 Mbps or 2400Mbps

Indicators| Multi-color status LED

Safety standards

| UL 62368-1

CAN/CSA-C22.2 No. 62368-1-14

UL 2043

ICES-003:2020 Issue 7, Class B (Canada)

Suitable for use in environmental air space in accordance with Section 300-22(C) of the National Electrical Code, and Sections 2-128, 12-010(3), and 12-100 of the Canadian Electrical Code, Part 1, CSA C22.1.

Warranty Information

The AP45 family of Access Points comes with a limited lifetime warranty.

Ordering Information:

Access Points

Mounting brackets

APBR-U| Universal AP Bracket for T-Rail and Drywall mounting for Indoor Access Points
---|---
APBR-ADP-T58| Adapter for 5/8-inch threaded rod bracket
APBR-ADP-M16| Adapter for 16mm threaded rod bracket
APBR-ADP-T12| Adapter for 1/2-inch threaded rod bracket
APBR-ADP-CR9| Adapter for channel rail and recessed 9/16” t-rail
APBR-ADP-RT15| Adapter for recessed 15/16″ t-rail
APBR-ADP-WS15| Adapter for recessed 1.5″ t-rail

Power Supply options

• 802.3at or 802.3bt PoE power

FCC STATEMENT

Regulatory Compliance Information

This product and all interconnected equipment must be installed indoors within the same building, including the associated LAN connections as defined by the 802.3at Standard. Operations in the 5.15GHz – 5.35GHz band are restricted to indoor usage only. If you need further assistance with purchasing the power source, please contact Juniper Networks, Inc.

FCC Requirement for Operation in the United States of America:

FCC Part: 15.247, 15.407, 15.107, and 15.109

FCC Guideline for Human Exposure

This equipment complies with FCC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance between the radiator & your body; AP45 – 50cm and AP45E – 59cm. This device complies with Part 15 of the FCC Rules. Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

This equipment has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful interference in a residential installation. This equipment generates, uses and can radiate radio frequency energy and, if not installed and used in accordance with the instructions, may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment off and on, the user is encouraged to try to correct the interference by one of the following measures:

• Reorient or relocate the receiving antenna.
• Increase the separation between the equipment and receiver.
• Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.
• Consult the dealer or an experienced radio/TV technician for help.

FCC Caution

• Any changes or modifications not expressly approved by the party responsible for compliance could void the user’s authority to operate this equipment.
• This transmitter must not be co-located or operating in conjunction with any other antenna or transmitter.
• For operation within 5.15 ~ 5.25GHz / 5.47 ~5.725GHz / 5.925 ~ 7.125GHz frequency range, it is restricted to indoor environment.
• The 5.925 ~ 7.125GHz operation of this device is prohibited on oil platforms, cars, trains, boats, and aircraft, except that operation of this device is permitted in large aircraft while flying above 10,000 feet.
• Operation of transmitters in the 5.925-7.125 GHz band is prohibited for control of or Communications with unmanned aircraft systems.

Industry Canada

This device contains license-exempt transmitter(s)/receiver(s) that comply with Innovation, Science and Economic Development Canada’s license-exempt RSS(s). Operation is subject to the following two conditions:

1. This device may not cause harmful interference
2. This device must accept any interference received, including interference that may cause undesired operation.

This radio transmitter [22068-AP45] has been approved by Innovation, Science and Economic Development Canada to operate with the antenna types listed below, with the maximum permissible gain indicated. Antenna types not included in this list that have a gain greater than the maximum gain indicated for any type listed are strictly prohibited for use with this device.

Approved antenna(s) list

AP45

|

Note1

2| Juniper| AP45| PIFA
3| Juniper| AP45| PIFA
4| Juniper| AP45| PIFA
5| Juniper| AP45| PIFA
6| Juniper| AP45| PIFA
7| Juniper| AP45| PIFA
8| Juniper| AP45| PIFA
9| Juniper| AP45| PIFA
10| Juniper| AP45| PIFA
11| Juniper| AP45| PIFA
12| Juniper| AP45| PIFA
13| Juniper| AP45| PIFA
14| Juniper| AP45| PIFA
15| Juniper| AP45| PIFA| AP45, AP45E

16

|

AccelTex

|

ATS-OO-2456-466-10MC-36

|

OMNI

|

AP45E

17

|

AccelTex

|

ATS-OP-2456-81010-10MC-36

|

Panel

18

|

AccelTex

|

ATS-OO-2456-466-10MC-36

|

OMNI

19

|

AccelTex

|

ATS-OP-2456-81010-10MC-36

|

Panel

Note 1

Ant.

| Antenna Gain (dBi)
---|---
WLAN 5GHz

(Radio 1)

|

WLAN 2.4GHz

(Radio 2)

| WLAN 5GHz

(Radio 2)

| WLAN 6GHz

(Radio 3)

|

WLAN 2.4GHz

(Radio 4)

| WLAN 5GHz

(Radio 4)

| WLAN 6GHz

(Radio 4)

|

Bluetooth (Radio 5)

UNII 1| UNII 2A| UNII 2C| UNII 3| UNII 1| UNII 2A| UNII 5| UNII 6| UNII 7| UNII 8| UNII 1| UNII 2A| UNII 2C| UNII 3| UNII 5| UNII 6| UNII 7| UNII 8
1| 2.89| 3.7| 3.46| 2.39| 2.01| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –
2| 2.61| 2.55| 3.04| 3.8| 0.66| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –
3| 1.94| 2.2| 2.82| 2.54| 2.04| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –
4| 3.27| 4.06| 2.87| 2.17| 1.17| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –
5| –| –| –| –| –| 3.2| 3.56| –| –| –| –| –| –| –| –| –| –| –| –| –| –
6| –| –| –| –| –| 2.85| 3.77| –| –| –| –| –| –| –| –| –| –| –| –| –| –
7| –| –| –| –| –| 3.37| 3.23| –| –| –| –| –| –| –| –| –| –| –| –| –| –
8| –| –| –| –| –| 3.11| 3.68| –| –| –| –| –| –| –| –| –| –| –| –| –| –
9| –| –| –| –| –| –| –| 4.9| 5.4| 5.4| 5.6| –| –| –| –| –| –| –| –| –| –
10| –| –| –| –| –| –| –| 4.9| 5.4| 5.4| 5.6| –| –| –| –| –| –| –| –| –| –
11| –| –| –| –| –| –| –| 4.9| 5.4| 5.4| 5.6| –| –| –| –| –| –| –| –| –| –
12| –| –| –| –| –| –| –| 4.9| 5.4| 5.4| 5.6| –| –| –| –| –| –| –| –| –| –
13| –| –| –| –| –| –| –| –| –| –| –| 5.0| 5.4| 5.4| 5.5| 5.3| 4.7| 4.8| 4.8| 4.1| –
14| –| –| –| –| –| –| –| –| –| –| –| 5.0| 5.4| 5.4| 5.5| 5.3| 4.7| 4.8| 4.8| 4.1| –
15| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –| 4.5
16| 6| 6| 6| 6| 4| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –
17| 10| 10| 10| 10| 8| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –| –
18| –| –| –| –| –| –| –| 6| 6| 6| 6| 4| 6| 6| 6| 6| 6| 6| 6| 6| –
19| –| –| –| –| –| –| –| 10| 10| 10| 10| 8| 10| 10| 10| 10| 10| 10| 10| 10| –

IC Caution

1. The device for operation in the band 5150-5250 MHz is only for indoor use to reduce the potential for harmful interference to co-channel mobile satellite systems;
2. The maximum antenna gain permitted for devices in the bands 5250-5350 MHz and 5470-5725 MHz shall be such that the equipment still complies with the e.i.r.p. limit;
3. The maximum antenna gain permitted for devices in the band 5725-5850 MHz shall be such that the equipment still complies with the e.i.r.p. limits specified for point-to-point and non-point-to-point operation as appropriate; and
4. Operation shall be limited to indoor use only.
5. Operation on oil platforms, cars, trains, boats and aircraft shall be prohibited except for on large aircraft flying above 10,000 ft.

Radiation Exposure Statement

• This equipment complies with IC RSS-102 radiation exposure limits set forth for an uncontrolled environment.
• This equipment should be installed and operated with minimum distance 24cm (AP45), 34cm (AP45E) between the radiator & your body.

EU Declaration

CE

Hereby, Juniper Networks, Inc. declares that the radio equipment types (AP45, AP45E) are in compliance with Directive 2014/53/EU. The full text of the EU declaration of conformity is available at the following: https://www.mist.com/support/

The frequency and maximum transmitted Power in EU:

Bluetooth

WLAN

This equipment complies with EU radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. The device is restricted to indoor use only when operating in 5150 to 5350 MHz and 5945 to 6425MHz frequency ranges.

| AT| BE| BG| CZ| DK| EE| FR| DE| IS
---|---|---|---|---|---|---|---|---|---
IE| IT| EL| ES| CY| LV| LI| LT| LU
HU| MT| NL| NO| PL| PT| RO| SI| SK
TR| FI| SE| CH| HR| UK(NI)| |

UK

Hereby, Juniper Networks, Inc. declares that the radio equipment types (AP45, AP45E) are in compliance with Radio Equipment Regulations 2017. The full text of the UK declaration of conformity is available at the following: https://www.mist.com/support/

The frequency and maximum transmitted Power in UK:

Bluetooth:

WLAN

This equipment complies with UK radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator & your body. The device is restricted to indoor use only when operating in 5150 to 5350 MHz and 5925 to 6425MHz frequency ranges.

| UK(NI)
---|---

Japan

AP45 and AP45E Access Points are restricted to indoor use only when operating in 5150-5350MHz and 5925 to 6425MHz frequency ranges.

Juniper Networks (C) Copyright 2021-2023. All Rights Reserved

References

• Support - Mist

Read User Manual Online (PDF format)

Read User Manual Online (PDF format)  >>

Download This Manual (PDF format)

Download this manual  >>