mifa A10 Plus Speaker Bluetooth Portable Wireless Stereo User Manual
- June 13, 2024
- MiFa
Table of Contents
A10+ SPEAKER
USER MANUAL
01 Warning
- To ensure proper use and trouble-free operation, please carefully read this user manual first.
- For The First Use, a full charge is recommended.
- Please Use And Store The Product At Room Temperature.
- Do Not Throw And Drop The Product To Avoid Damages.
- Do not expose the product to fire, high temperature, direct sunlight, etc.
- Do not use organic solvents or other chemicals to clean the product.
- Do not allow small particles to get into the Product.
- Please keep volumes of the speaker mode rate avoid temporary or permanent hearing impairment.
- Do not disassemble the product, or make any modifications to the structure or any parts of it.
- Keep the product out of children’s reach.
02 Packing list
1 × A10+ Bluetooth Speaker
1 × Detachable Strap
1 × USB Type-C Charging Cable 1 × 3.5 mm Audio Cable
1 × User Manual
03 Keys Functions
-
Short Press: Decrease volume
Long Press: Play previous song -
Short Press: Play or pause
-
Bluetooth Button: Press And Hold The Button For 2 seconds to disconnect the paired device and the speaker enters pairing mode. Short press it again to reconnect it to the last-connected device.
-
Indicator Play Mode (micro SD card or USB flash driver should be inserted)
-
Play Mode Button: Short press it to play songs randomly and indicator flashes; press again to put a song on repeat and the indicator stays on; press again to play all the songs in a loop and indicator turns off.
-
LED Indicator
White light flashes after powered on
White light stays on after connected to a device
White light stays on while playing
White light flashes slowly when playing is paused
White light flashes rapidly at the max/min volume -
Built-in Microphone
-
Power Button: Press and hold the button for 2 seconds turn on turn off; press and hold the button for 8 seconds to reset.
Mode Button: Short press to switch the mode in the powered-on status
If it is inserted with a Micro SD card, an USB flash drive and an audio cable, modes switching turns: Bluetooth mode → Micro SD card mode → USB flash driver mode → Aux-in mode -
Call Answer Button: Short press to answer or hang up; long press to reject.
-
Short Press: Increase volume
Long Press: Play next song
04 Ports Functions
-
Aux-in jack
Inserted an audio cable in the powered-on state, it will enter the Aux-in mode automatically.
Built-in reset button: Press the reset button in the jack with a needle to reset speaker. -
USB flash driver Port
Inserted an USB flash driver in the powered-on state, it will play the music stored in the driver automatically after beeps. -
USB Type-C Port: Use C 5V/ 1A adaptor to charge the speaker
-
Charging Indicator: Red light will stay on when charging, turn off after finish charging.
-
Micro SD Card Slot
In the powered-on state, insert a Micro-SD card, it will play the music stored in the card automatically after beeps.
05 Bluetooth Connection
1. Turn on the speaker
Press and hold the power button for 2 seconds to turn on the speaker with a
prompt sound. And the white LED light flashes indicating it is in the pairing
mode.
2. Connect it to your device
Turn on the Bluetooth of your device and select Mifa_A10+. Once the
connection is completed, it will beep and the white LED light will stay on.
The speaker will connect to the last-connected device automatically once the device’s Bluetooth is turned on.
Other Instructions
To connect to another device, press and hold the Bluetooth button for 2
seconds to disconnect the paired one and the speaker will enter the pairing
mode. To reconnect it to the last used device, short press the Bluetooth
button.
06 True Wireless Stereo Function
Speaker 1
Speaker 2
1. Set up the TWS system
Turn on two A10+ speakers and make sure no device connects with either of
them. Double press one speaker’s Bluetooth button and there will be a beep
sound to indicate pairing is taking place. Once pairing is complete, there
will be another beep sound.
2. Pair two TWS speakers with a Bluetooth device
Select Mifa_A10+ in the Bluetooth settings menu of the Bluetooth device.
There will be a sound indicating a successful connection and the blue LED
indicator keeps on.
3. Stop the TWS
Double press either speaker’s button to disconnect it with the other one.
Tips:
- For the first time of setting up the TWS system, the speaker you press the Bluetooth button one will work as the main speaker and the other one as the dependent speaker.
- After the first connection, the main speaker will keep working as the main speaker and the dependent one will keep working as the dependent one in the future connection.
- After setting up the TWS system, the dependent speaker’s blue LED indicator stays on and the main one’s LED indicates your operation.
- The true wireless stereo function supports only 2 speakers.
- After the TWS system is set up successfully, you just need to operate either speaker. The other one will do the same operation simultaneously.
07 Specifications
Technical Parameters
Speaker Type| Portable Bluetooth Speaker
Speaker System| Dual-channel + 2 Low frequency amplifiers
Loudspeaker| Dual internal magnetic speakers + 2 Low frequency amplifiers
Output Power| 20W
Frequency Response| 20 Hz – 20 Khz
Supported Storage| Up to 32 GB storage device
Bluetooth Version| Bluetooth 5.0
Bluetooth Range| 10 Meters
Battery| Built-in 2600 mAh Lithium battery
Input| 5V/ 1A
Function
Link two A10+ speakers in Bluetooth mode to form true wireless stereo system
Support voice chat or phone call with the built-in mic
Support single cycle play or order play in Micro SD card mode and USB flash
driver mode
Supported Media Type| APE/ FLAC/ WAV/ WMA/ MP3
Bit Rate| MP3: 8Kbps-320Kbps
WMA: 5Kbps-384Kbps
APE: 100Kbps-1200Kbps
FLAC: 100Kbps-1200Kbps
WAV: 32Kbps-384Kbps
Size: 188 70 73 mm
Weight: 531g (including the built-in Lithium battery)
08 Trouble Shooting
FAQ
|
Solutions
---|---
Not able to connect to your device| 1. Restart the speaker and try again
2. If your device requires a Pin Code, please enter 0000
Keeps cutting out when playing| Please ensure the speaker is within the
operating range and there are no obstacles between the speaker and the device
Not able to play the music in Micro SD card|
- Please ensure the format of the Micro SD card is FAT32. It only supports FAT32 Micro SD card
- Please ensure the formats of the music files are APE, FLAC, WAV, WMA or MP3
No sound when playing|
- Please adjust the volume of the speaker
- Please adjust the volume of your device
- Please check if the speaker is paused
No sound in AUX-in mode| Please ensure the audio cable is connected well
Not able to turn on| Please try to charge the speaker for about 3 hours
No respond to any operation| Please try to reset the speaker by pressing the
reset button in the AUX-in jack
MIFA INNOVATIONS LLC
www.mifa.net Designed in US Made in China
Copyright © MIFA. All rights reserved.
MIFA, the MIFA logo and other MIFA marks are all owned and registered by MIFA
INNOVATIONS LLC. All other trademarks are the property of their respective
owners. The information contained here is subject to change without prior
notice.
This device complies with part 15 of the FCC Rules. Operation is subject to
the following two conditions: (1) this device may not cause harmful
interference, and (2) this device must accept any interference received,
including interference that may cause undesired operation.
Any changes or modifications not expressly approved by the party responsible
for compliance could void the user’s authority to operate the equipment.
NOTE: This equipment has been tested and found to comply with the limits for a
Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are
designed to provide reasonable protection against harmful interference in a
residential installation. This equipment generates, uses and can radiate radio
frequency energy and, if not installed and used in accordance with the
instructions, may cause harmful interference to radio communications. However,
there is no guarantee that interference will not occur in a particular
installation.
If this equipment does cause harmful interference to radio or television
reception, which can be determined by turning the equipment off and on, the
user is encouraged to try to correct the interference by one or more of the
following measures:
— Reorient or relocate the receiving antenna.
— Increase the separation between the equipment and receiver.
— Connect the equipment into an outlet on a circuit different from that to
which the receiver is connected.
— Consult the dealer or an experienced radio/TV technician for help. The
device has been evaluated to meet general RF exposure requirement. The device
can be used in portable exposure condition without restriction
FCC ID: 2AF7A-A100
MIFA INNOVATIONS LLC
www.mifa.net Designed in US Made in China
Copyright © MIFA. All rights reserved.
MIFA, the MIFA logo and other MIFA marks are all owned and registered by MIFA
INNOVATIONS LLC. All other trademarks are the property of their respective
owners. The information contained here is subject to change without prior
notice.
References
Read User Manual Online (PDF format)
Read User Manual Online (PDF format) >>